• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.1831-1838
• /
• 1991

The deformation of coil spring with noncircular section, which is used in the engine valve of automobiles under the applied load is usually accompanied by sectional warping and additional displacements of geometric center. In this study the isoparametric beam element formulations are modified and expanded to consider these two effects. To verify these formulations, simple torsion tests are made and compared with the analysis results. For the case of the zero-pitch spring, the stress distributions of oval and circular section are coincided with those of the analysis using the solid elements. Cylindrical coil springs with oval section are analyzed. These results are agreed with those of Nagaya.

• Fibers and Polymers
• /
• v.4 no.4
• /
• pp.199-203
• /
• 2003

In order to investigate the effects of cross-sectional shapes on the sound characteristics of polyester fibers, 10 specimens were woven into a twill structure made of round, hollow, triangular, u-shape, cruciform, and composite cross-sectional (▲/▲ ,()/▲, Y/Y) fibers. Their rustling sounds were recorded, and their sound spectra were obtained from FFT analysis. Physical sound parameters (LPT, ΔL, Δf) and Zwicker's psychoacoustic parameters of the loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z) were calculated from the sound spectra. According to noncircular cross-section fibers, the hollow shaped fiber had the highest value of LPT, ΔL, loudness(Z), and fluctuation strength(Z). The triangular shaped fiber had a lower value of LPT, ΔL, loudness(Z), and roughness(Z) than those of the round shaped fiber. Among composite cross-section fibers, C1(▲/▲) and C3 (Y/Y) had higher values of LPT, ΔL, Δf and loudness(Z) but C2(()/▲) had lower values. Also the LPT, ΔL, sharpness(Z), and roughness(Z) values of different denier were similar to each other, but the Δf and loudness(Z) values increased as the denier increased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.743-749
• /
• 2014

In this study, a noncircular drawing (NCD) sequence for manufacturing high-strength and high-ductility pearlitic steel wires was investigated. Multipass NCD was conducted up to the 12th pass at room temperature with two processing routes (defined as the NCDA and NCDB), and compared with the wire drawing (WD). During the torsion test, delamination fracture in the drawn wire was observed in the 10th pass of the WD whereas it was not observed until the 12th pass of the NCDB. From X-ray diffraction, the circular texture component that increases the likelihood of delamination fracture of the drawn wire was rarely observed in the NCDB. Thus, the improved ability of the multipass NCDB to manufacture high-strength pearlitic steel wires with high torsional ductility compared to the WD (by reducing the likelihood of delamination fracture) was demonstrated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.8
• /
• pp.1150-1157
• /
• 2003

Nonlinear relationship between Reynolds stresses and the rate of strain of nonlinear k-$\varepsilon$models is evaluated theoretically by using the boundary layer assumptions against the turbulence-driven secondary flows in noncircular ducts and then their prediction performance is validated numerically through the application to the fully developed turbulent flow in a square duct. Typical predicted quantities such as mean axial and secondary velocities, turbulent kinetic energy and Reynolds stresses are compared with available experimental data. The nonlinear k-$\varepsilon$ model adopted in a commercial code is found to be unable to predict accurately duct flows with the prediction level of secondary flows one order less than that of the experiment.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1814-1820
• /
• 2003

Nonlinear relationship between Reynolds stresses and the rate of strain of nonlinear ${\kappa}-{\epsilon}$ models is evaluated theoretically by using the boundary layer assumptions against the turbulence-driven secondary flows in noncircular ducts and then their prediction performance is validated numerically through the application to the fully developed turbulent flow in a square duct. Typical predicted quantities such as mean axial and secondary velocities, turbulent kinetic energy and Reynolds stresses are compared with available experimental data. The nonlinear model adopted in a commercial code is found to be unable to predict accurately duct flows with the prediction level of secondary flows one order less than that of the experiment.

• The Journal of Information Technology
• /
• v.6 no.4
• /
• pp.113-123
• /
• 2003

This paper is the study for code generation using attribute grammar without cycle. For the purpose of this study, we designed metalanguage SDL which describes an attribute grammar and, represented attribute grammar to SDL. This attribute grammar is based on L-attributed grammar without cycle. This system consists of attributed-grammar analyzer and attribute evaluator. Attributed grammar analyzer takes a semantic description language and then generates useful informations that are needed by attribute evaluator. The evaluator calculates an attribute values using these information.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.45-51
• /
• 1995

자동차 엔진의 피스톤은 핀 구멍의 복잡한 형상과 2사이클 엔진의 경우 실린더쪽 흡기 및 배기 포트의 위치에 따라 균일하지 않은 열이나 응력 등의 영향에 의한 변형을 고려하여, 상온에서의 형상이 각종 평가 시험을 거쳐 엔진마다 다양한 형상을 갖는 피스톤으로 결정된다. 본 연구에서는 컴퓨터 제어에 의한 방법으로서 타원형상을 갖는 임의의 피스톤을 고속, 고정도로 가공할 수 있는 CNC(Computer Numerical Control)선반 개발에 관하여 연구 하였다. 피스톤 데이터를 퍼스널 컴퓨터로 입력하고 CNC 제어하므로 마스터캠의 제작 불필요, Recess 등과 같은 미세가공 가능, 피스톤의 형상변경 용이, 고속가공 등으로 모방절삭 방식보다 훨씬 높은 생산성 향상이 기대된다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.193-199
• /
• 2000

Control system for cutting piston used in vehicle that is one of the 3D shape cutting using CNC lathe is presented. In order to cut the hybrid piston shape using CNC lathe, defined piston shape and change into machine code. The control software was developed for the high speed piston shape cutting. In this paper, the performance of this software was evaluated practically. As a result, the evaluated cutting precision was quantitatively compared with theoretical precision. Also the productivity and the quality by using CNC lathe with control software were evaluated those by using profiling.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.3094-3104
• /
• 1993

The five punch and die sets are selected as the examples of arbitrary cross sections which have two opposite inclined sides. Two kinds of blank shapes are designed for all cross sections. One(h-b1.) is determined by slip-line theory and the other (G-b1.) is determined conventionally as the similar shapes with the cross sections which were used by Gopinathan. As a result of the experimental procedures, the superiority of the blank shapes designed by slip-line theory is verified in the limiting drawing ratio, the uniformity of cup height and the thickness distributions.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.4
• /
• pp.152-162
• /
• 1996

The purpose of this study is the development of a lathe which can cut any pistons of oval shape with high speed, accuracy and precision by CNC (Computer Numerical Control) method. Y axis which is the position determinating mechanism with high speed response was added to the CNC lathe and the ovality and profile was cut under the control of C-Y-Z axes at same time. In the case of ovality of .phi. 0.2mm, the productivity can be improved up to 2500rpm(Y axis:83Hz) by high speed cutting than modeling method. Since a personal computer is used, it is easy to change the shape of pistion and can be applied promptly to many types of piston shppe by only changing data files.