• 대한조선학회논문집
• /
• 제56권4호
• /
• pp.352-360
• /
• 2019

International Maritime Organization (IMO) regulates an emission of greenhouse gases by creating an Energy Efficiency Design Index (EEDI) to reduce environmental pollution. In propulsion system field, studies are under way on Energy Saving Device (ESD), which can improve propulsion efficiency with the propeller, to reduce the EEDI. Among the studies, the study of Pre-Swirl Stator (PSS) has been actively conducted from long time ago. Recently the variable pith angle type pre-swirl stator has been studied to improve the propulsion efficiency in non-uniform flow fields of the Stern. However, for traditional design methods, no specific design method has been established on the blade or location of radius. In this study, proper design method is proposed for each blade or location for radius according to hydrodynamic pitch angle.

• 한국정밀공학회지
• /
• 제28권1호
• /
• pp.63-72
• /
• 2011

In recent years, hot-stamped components are more increasingly used in the automotive industry in order to reduce weight and to improve the strength of vehicles. In hot stamping process, blank is hot formed and press hardened in a tool. However, in hot stamping without cooling channel, temperature of the tool increases gradually in mass production thus cannot meet the critical cooling rate to obtain high strength over 1500MPa. Warpage occurs in the hot stamped component due to non-uniform stress state caused by unbalanced cooling. Therefore, tools should be uniformly as well as rapidly cooled down by the coolant which flows through cooling channel. In this paper, optimal design method of cooling channel to obtain uniform and high strength of the component is proposed. Optimized cooling channel is applied to the hot press V-bending process. As a result of measuring strength, hardness and microstructure of the hot formed parts, it is known that the design methodology of cooling channel is effective to the hot stamping process.

• KIEAE Journal
• /
• 제7권5호
• /
• pp.29-34
• /
• 2007

Discomfort glare from windows is an important issue in window and daylighting design. This study aims to investigate the effect of luminance difference between the lower and the upper part of a large glare source. Experiments were conducted using a luminous body divided into two parts, the upper part and the lower part. The degree of discomfort glare from the luminous body was examined. The result shows that the part with lower luminance is perceived as a glare source when the part has higher luminance then the background luminance. The degree of discomfort glare was estimated for the experimental conditions, and compared to the observations. The estimation was made using two methods: one summed the glare sensation for each section, and the other used the average luminance of the whole luminous body. The result of the comparison shows that the method using the average luminance has approximate values to the observations. Consequently, the use of the average luminance was proposed for evaluation of discomfort glare from non-uniform large glare sources.

• Geomechanics and Engineering
• /
• 제13권5호
• /
• pp.757-774
• /
• 2017

The subgrade reaction modulus of a large mat foundation was investigated by using a numerical analysis and a field case study. The emphasis was on quantifying the appropriate method for determining the subgrade reaction modulus for the design of a flexible mat foundation. A series of 3D non-linear FE analyses are conducted with special attention given to the subgrade reaction modulus under various conditions, such as the mat width, mat shape, mat thickness, and soil condition. It is shown that the distribution of the subgrade reaction modulus is non-uniform and that the modulus of subgrade reaction at both the corners and edges should be stiffer than that at the center. Based on the results obtained, a simple modification factor for the subgrade reaction modulus is proposed depending on the relative positions within the foundation in weathered soil and rocks.

• 한국생활과학회지
• /
• 제14권6호
• /
• pp.995-1006
• /
• 2005

The purpose of this study was to investigate the wearing sensation and satisfaction of high school girls' winter uniform jackets according to the fabrics and the shapes. The fabrics were divided into four parts of stretch and non-stretch woven fabrics. The shapes were divided into two parts of tight and general types. The results were as followings: 1. In the aspect of the appearance evaluation for the uniform jackets, silhouette and length item showed significant differences in fabric and shape. The non-stretch woven fabric and tight type was more satisfying than the stretch fabric and general type because its silhouette and length were shorter and fitter than the stretch one and general type. The jackets of non-stretch woven fabric of tight type were evaluated as the thinnest in the silhouette and were evaluated as the shortest in the length. Conversely, the jackets of stretch woven fabric of general type were evaluated as the thickest and longest. 2. As for the wearing sensation of school uniform jacket, all test items showed significant differences in fabric and shape. The stretch fabric and general type was more satisfying than the non-stretch woven fabric and tight type because the jacket of stretch fabric and general type was felt more comfortable in activities, and wearing. Accordingly, the appearance evaluation for uniforms' jacket is in sharp contrast with that of wearing sensation.

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.367-376
• /
• 2016

This paper presents a cell balancing method for a single switch flyback converter with a multi-winding transformer. The conventional method using a flyback converter with a multi-winding transformer is simple and easy to control, but the voltage of each secondary winding coil might be non-uniform because of the unequal effective turn-ratio. In particular, it is difficult to control the non-uniform effect using turn-ratios because secondary coil has a limited number of turns. The non-uniform secondary voltages disturb the cell balancing procedure and induce an unbalance in cell voltages. Individual cell control by adding a switch for each cell can reduce the undesirable effect. However, the circuit becomes bulky, resulting in additional loss. The proposed method here uses the conventional flyback converter with an adjustment made to the output filters of the cells, instead of the additional switch. The magnitude of voltage applied to a particular cell can be reduced or increased according to the adjusted filter and the selected switching frequency. An analysis of the conventional converter configuration and the filter design method reveals the possibility of adequate cell balancing control without any additional switch on the secondary side.

• Steel and Composite Structures
• /
• 제18권2호
• /
• pp.375-394
• /
• 2015

This paper presents the results of four long-term experiments carried out to investigate the time-dependent behaviour of composite floor slabs with particular attention devoted to the development of non-uniform shrinkage through the slab thickness. This is produced by the presence of the steel deck which prevents moisture egress to occur from the underside of the slab. To observe the influence of different drying conditions on the development of shrinkage, the four 3.3 m long specimens consisted of two composite slabs cast on Stramit Condeck $HP^{(R)}$ steel deck and two reinforced concrete slabs, with the latter ones having both faces exposed for drying. During the long-term tests, the samples were maintained in a simply-supported configuration subjected to their own self-weight, creep and shrinkage for four months. Separate concrete samples were prepared and used to measure the development of shrinkage through the slab thickness over time for different drying conditions. A theoretical model was used to predict the time-dependent behaviour of the composite and reinforced concrete slabs. This approach was able to account for the occurrence of non-uniform shrinkage and comparisons between numerical results and experimental measurements showed good agreement. This work highlights the importance of considering the shrinkage gradient in predicting shrinkage deformations of composite slabs. Further comparisons with experimental results are required to properly validate the adequacy of the proposed approach for its use in routine design.

• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.75-80
• /
• 2015

Nowadays, flat-shaped cover glass is widely used for mobile devices. However, for its good design and convenience of use, curved cover glass has been demanded. Thus, many companies have tried to produce curved cover glass through the shaving technique, but the production efficiency is very low. Therefore, the molding technique has been adopted to increase the efficiency for the curved-glass production system. For a glass-molding system, several heating blocks are installed, and the flat cover glass is sequentially heated and molded. The production time for the cover glass is very different depending on the heating conditions; thus, the prediction of the production time for different heating conditions should be needed. Therefore, in this study, the computations were performed with different heating conditions (uniform and non-uniform) in the present cover glass-molding machine. For uniform and non-uniform heating conditions, the simple correlation between the heating time and the heater capacity and the heating time to achieve higher durability can be suggested, respectively.

• 한국소음진동공학회논문집
• /
• 제19권6호
• /
• pp.620-627
• /
• 2009

Shaking table test was carried out to obtain dynamic characteristics of TLCDs with uniform and non-uniform sections for both horizontal and vertical tubes. The input to the table is harmonic acceleration with constant magnitude. The output is horizontal dynamic force which is measured by load cell installed below the TLCD. Transfer functions are experimentally obtained using the ratio of input and output. Natural frequency, the most important design factor, is compared to that by theoretical equation for TLCDs with five different water levels. System identification process is performed for experimentally obtained transfer functions to find the dynamic characteristics of head loss coefficient and effective mass of TLCDs. It is found that their magnitudes are larger for a TLCD with non-uniform section than with uniform section and natural frequencies are close to theoretical ones.

• 대한가정학회지
• /
• 제50권7호
• /
• pp.37-48
• /
• 2012

The purpose of this study was conducted to improve middle and high school students' satisfaction on their uniforms and to provide basic information for their better size systems. This study analyzed the purchasing and modification behavior, fitting evaluation, and size decision aspect of students. This study was surveyed middle and high schools students in Daegu City. The collected data were analyzed by frequency analysis, percentage, t-test, chisquare test. The results of this study are as follows; 61.3% of the students interviewed have experienced to modify their uniforms. Since the unfittable size and non-fashionable design caused the students to modify their uniforms, it seems necessary to set up the various uniform sizes, as well as figuring out its aesthetic characteristic. Between middle school and high school students, and students with a uniform modification and students without a uniform modification, there were partially differences in fitting evaluation, and size decision.