• 대한기계학회논문집B
• /
• 제25권4호
• /
• pp.507-513
• /
• 2001

Time averaged pressure distributions in a high-speed centrifugal compressor channel diffuser at design and off-design flow rates are investigated. Pressure distributions from the impeller exit to the channel diffuser exit are measured for various flow rates from choke to near surge condition, and the effects of operating condition are discussed. The strong non-uniformity in the pressure distribution is obtained over the vaneless space and semi-vaneless space caused by the impeller-diffuser interaction. As the flow rate increases, flow separation near the throat, due to large incidence angle at the vane leading edge, increases aerodynamic blockage and reduces the aerodynamic flow area downstream. Thus the minimum pressure location occurs downstream of the geometric throat, and it is named as the aerodynamic throat. And at choke condition, normal shock occurs downstream of this aerodynamic throat. The variation in the location of the aerodynamic throat is discussed.

• 설비공학논문집
• /
• 제13권1호
• /
• pp.38-47
• /
• 2001

The operation characteristics of variable conductance heat pipe(VCHP) were numerically investigated by using 1-dimensional diffuse-front model. For different boundary conditions, the amount of non-condensible gas charge and dimension of gas reservoir were obtained by iterative calculation. It is found that the amount of non-condensible gas charge and dimensions of gas reservoir have an effect on the temperature control of condenser for the given operating condition of VCHP. The numerical results show that VCHP has an excellent capability of temperature control when subjected to a change in the heat input.

• Journal of Welding and Joining
• /
• 제11권3호
• /
• pp.22-33
• /
• 1993

Arc sensor is indispensable to arc welding robot systems for compensating the joint misalignment such as mismatch of the workpiece, ill-conditioned positioner and thermal deformation during welding. Furthermore, the amount of these mismatches cannot be preivously expected, and changes from time to time. There are many kinds of seam trackers for correcting the welding path of the robot, where non-contact type sensors arc prevalently used in arc welding robot systems. In this study, an arc sensor was developed for GMA and FCA welding robot system. Since the arc sensor uses the arc characteristics during welding, the operating principle of the arc sensor must be adjusted according to the welding condition. Especially in GMA welding with the $CO_{2}$ shielding gas, the welding arc is not stable because of the short circuit and non-axial globular transfer mode of the molten droplet. In this study, the 2nd order least square curve fitting algorithm was adopted and the applicability of this algorithm was investigated for robot welding systems. For easy usage of the arc sensor, the operating parameters for arc sensor were limited to eight which can be easily determined by the operator.

• Journal of Power Electronics
• /
• 제5권1호
• /
• pp.20-28
• /
• 2005

This paper presents a fuzzy predictive sliding mode control for high performance induction motor position drives. A new simplified inner-loop sliding-mode current control scheme based on a nonlinear mathematical model of an induction motor is introduced. Novel predictive fuzzy logic PI and PID controllers are used in speed and position loops, respectively. Sliding-mode current controllers and fuzzy predictive logic controllers are designed based on indirect vector control. The overall system performance is examined under different dynamic operating conditions. The performance of the drive system is robust and stable, and insensitive to parameters and operating condition variations even though non-exact system parameters are used in the implementation of the proposed controllers.

• 한국유체기계학회 논문집
• /
• 제1권1호
• /
• pp.64-71
• /
• 1998

The non-uniform pressure generated in the volute generally are propagating upstream. As a result, outlet conditions of rotaing impeller are changed and the performance degrades. The major object of this research is to develop the numerical method which can calculate the effects of impeller and volute flow field interactions. Under the assumption of steady three-dimensional incompressible turbulent flow, the time averaged N-S equations involving $k-{\epsilon}$ turbulent model was solved by the F.V.M. To verify the computational method, the calculations are compared with experimental results published in literature and show satisfactory agreement with them, The three-dimensional flow characteristics within the volute of a centrifugal fan at design and off-design operating points have also been studied.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.189-194
• /
• 2004

As a disk drive becomes widely used in portable environments, one of the important requirements is durability under severe environmental condition, especially, resistance to mechanical shock. An important challenge in the disk recording is to improve disk drive robustness in shock environments. If the system comes In contact with outer shock disturbance, the system gets critical damage in head-gimbal assembly or disk. This paper describes analysis of a HGA(head-gimbal assembly) in micro MO drives to shock loading during both non-operating state and operating state. A finite element model which consists of the disk, suspension, slider and air bearing was used to find structural response of micro MO drives. In the operational case. the air bearing is approximated with four linear elastic springs. The commercially available finite element solver, ANSYS/LS-DYNA, is used to simulate the shock response of the HGA in micro MO drives. In this paper, the mechanical robustness of the suspension is simuiated considering the shock responses of the HGA.

• 대한조선학회논문집
• /
• 제44권4호
• /
• pp.408-416
• /
• 2007

This paper summarizes an experimental study on the marine propeller BPF noise. The main objective of this study is to show the worthiness of the noise measurement at the MOERI middle size cavitation tunnel and to acquire useful propeller noise data. Background noise of MOERI(Maritime and Ocean Engineering Research Institute) cavitation tunnel is experimentally analyzed. Experiment carried out in the MOERI cavitation tunnel with wake screen or dummy body, which is simulated the wake. Propeller BPF noise is measured under various operating conditions. In order to secure the reliance of measured propeller noise dada, background noise of each operating conditions are measured and analyzed. The noise characteristics are analyzed according to the operating condition.

• The Journal of Asian Finance, Economics and Business
• /
• 제8권10호
• /
• pp.87-95
• /
• 2021

This study aims to demonstrate the impact of BPR in reducing cost in international business organizations by analyzing the impact of decentralization, re-engineering organizational structures, re-engineering human resources, industrial process technology, improving total quality standards, and value engineering. The study population includes all the international business organizations operating in the Middle East, with the condition that they operate in at least four countries. The results showed that there is a significant effect of all dimensions of BPR in reducing costs in international business organizations operating in the Middle East. When studying the impact of the dimensions combined, the moral effect appeared at each processes (decentralization, re-engineering of human resources and industrial process technology), while the moral effect did not appear in (rebuilding organizational structures, improving total quality standards, and value engineering). This does not negate the importance of the impact of these dimensions, but rather shows a disparity between dimensions in reducing cost, when studying its combined effect. The study recommends that organizations should adopt modern management accounting methods, including value engineering, in order to identify and enhance activities that add value to the organization's operations, as well as identify and eliminate non-value adding activities, in order to reduce costs.

• 한국유체기계학회 논문집
• /
• 제16권2호
• /
• pp.21-26
• /
• 2013

Super-cavitating vehicle which is operating under water speeds up to 100m/s. In this process super-cavitation around body reduces frictional resistance. This paper introduces experimental study on different width of suction path as there is a warhead in the torpedo. Hydraulic performances of turbopump at non-cavitating condition does not display a significant differences depending on different width of suction path. However, cavitation performance of each model shows obvious differences in the same condition of experience. In case of radial inlet, the value of critical NPSH(which indicates 3% head drop) increases about 20% in comparison of axial inlet.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.693-696
• /
• 2003

Hermetic Compressor circulates refrigerant with constant flow rate regardless of operation condition. so, at the operating condition requiring low cooling capacity, too much refrigerant flow deteriorates seasonal energy efficiency ratio(SEER). In this reason, modulated compressor is needed to improve SEER. Among many types of modulated compressor, non-inverter type modulated compressor is required for its low cost and easy to development. In the modulated scroll compressor by bypass method, EER steeply decreases for many loss like re-compression, changes of volume ratio, decrease of motor efficiency by torque variation. So. the range of modulation ratio for optimized SEER must be selected accompany with air conditioner set development.