• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.617-626
• /
• 2011

Seven post-tensioned lightweight concrete (LWC) beam specimens were tested under a symmetrical two-point top loading system. The parameters investigated were the amounts of mild longitudinal reinforcement and effective prestressing. The design compressive strength and dry density of the LWC tested were 30 MPa and 1,770 $kg/m^3$, respectively. Similar to post-tensioned normal weight concrete (NWC) beams, the crack propagation and stress increase of the unbonded tendons were significantly affected by the amounts of mild longitudinal reinforcement and effective prestressing. With the increase in the amounts of mild longitudinal reinforcement and effective prestressing, the serviceability and flexural capacity of the beams were enhanced whereas the stress increase in the unbonded tendons decreased. To control the crack width in post-tensioned LWC beams, a minimum amount of mild longitudinal reinforcement specified in ACI 318-08 provision is required. The flexural behavior of post-tensioned LWC beams and stress increase of the unbonded tendons could be rationally predicted by the proposed non-linear two-dimensional analysis. On the other hand, ACI 318-08 flexure provision was too conservative about the post-tensioned LWC beams.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.3
• /
• pp.255-265
• /
• 2009

Recently many studies have been published on application of immediate loaded implants. However, the immediate loading protocol has not been well documented. The purpose of the present study was to evaluate the stress distribution between bone-implant interfaces and the effect of implant length in the anterior maxilla using 3 dimensional finite element analyses. The diameter 4.0 mm threaded type implants with different length(8.5 mm, 10.0 mm, 11.5 mm, 13.0 mm, 15.0 mm) were used in this study. The bone quality of anterior maxillary bone block was assumed to D3 bone. Bone-implant interfaces of immediately loaded implant were constructed using a contact element for simulating the non osseointegration status. For simplification of all the processing procedures, all of the material assumed to be homogenous, isotropic, and linearly elastic. The 178 N of static force was applied on the middle of the palatoincisal line angle of the abutment with $120^{\circ}$ angle to the long axis of abutment. Maximum von Mises stress were concentrated on the labial cortical bone of the implant neck area, especially at the cortical-cancellous bone interfaces. Compared the different length, highest peak stress value was observed at the 8.5 mm implants and the results indicated a tendency towards favorable stress distribution on the bone, when the length was increased. Presence of cortical bone was very important to immediate loading, and it appears that implants of a length more than 13 mm are preferable for immediate loading at the anterior maxilla.

• Journal of dental hygiene science
• /
• v.9 no.2
• /
• pp.161-167
• /
• 2009

The purpose of this Study was to examine the effect of perfectionism on stress and anxiety during scaling practice in an effort to find efficient way of helping students with getting good skills. The subjects in this study were students who practiced a scaling at the oral hygiene practice lab in the Department of dental hygiene in S college from May 1 to May 31, 2008. They were divided into four groups based on their subscales of perfectionism : mixed perfectionist group, achievement striving perfectionist group, failure avoidance perfectionist group and non-perfectionist group. The measurements used were Two-Dimensional Perfectionism Scale, Stress level, Trait anxiety, State anxiety. There were no significant differences in the stress level before practice between 4 groups. There were significant differences in trait anxiety, state anxiety, total anxiety before scaling practice between 4 groups. However, these results were due to differences between mixed perfectionist group and non-perfectionist group. After practice, total anxiety was decreased from 93.71 to 89.66 and state anxiety was decreased from 45.49 to 43.38. These results were statistically significant. In order to investigate the influence of achievement striving factor and failure avoidance factor on the change of state anxiety during the scaling practice Standard Multiple Regression were employed for the statistical analysis. Failure avoidance factor was related with the increase of state anxiety during the scaling practice. So leachers have to give all effort to reduce the anxiety of students during scaling practice and provide students with motivation of achievement.

• Journal of Biomedical Engineering Research
• /
• v.25 no.4
• /
• pp.295-300
• /
• 2004

Coil embolization technique has been used recently to treat cerebral aneurysms. When a giant or a multilobular aneurysm are treated by roils, filling an aneurysm sac completely with coils is difficult and partial blocking of an aneurysm sac is inevitable. Blood flow characteristics, which nay affect the embolization process of an aneurysm sac, are changed by the locations of coils for the Partially blocked aneurysms. Blood flow fields are also influenced by the geometry of a parent vessel. In order to suggest the coil locations effective for aneurysm embolization, the blood flow fields of lateral aneurysm models were analyzed for the different coil locations and parent vessel geometries. Three dimensional pulsatile flow fields are analyzed by numerical methods considering non-Newtonian viscosity characteristics of blood. Flow rate into the aneurysm sac (inflow rate) and wall shear stress, which are suspected as flow dynamic factors influencing aneurysm embolization, are also calculated. Inflow rates were smaller and the low wall shear stress zones were larger in the neck blocked models compared to the dome blocked models. Smaller inflow and larger low wall shear stress zones in the distal neck blocked model imply that the distal neck should be the effective coil locations for aneurysm embolization.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.21 no.1
• /
• pp.1-14
• /
• 2005

The purpose of this study was to assess the loading distributing characteristics of implant prosthesis of internal connection system(ITI system) according to position and direction of load, under vertical and inclined loading using finite element analysis (FEA). The finite element model of a synOcta implant and a solid abutment with $8^{\circ}$ internal conical joint used by the ITI implant was constructed. The gold crown for mandibular first molar was made on solid abutment. Each three-dimensional finite element model was created with the physical properties of the implant and surrounding bone. This study simulated loads of 200N at the central fossa in a vertical direction (loading condition A), 200N at the outside point of the central fossa with resin filling into screw hole in a vertical direction (loading condition B), 200N at the centric cusp in a $15^{\circ}$ inward oblique direction (loading condition C), 200N at the in a $30^{\circ}$ inward oblique direction (loading condition D) or 200N at the centric cusp in a $30^{\circ}$ outward oblique direction (loading condition E) individually. Von Mises stresses were recorded and compared in the supporting bone, fixture, and abutment. The following results have been made based on this study: 1. Stresses were concentrated mainly at the ridge crest around implant under both vertical and oblique loading but stresses in the cancellous bone were low under both vertical and oblique loading. 2. Bending moments resulting from non-axial loading of dental implants caused stress concentrations on cortical bone. The magnitude of the stress was greater with the oblique loading than with the vertical loading. 3. An offset of the vertical occlusal force in the buccolingual direction relative to the implant axis gave rise to increased bending of the implant. So, the relative positions of the resultant line of force from occlusal contact and the center of rotation seems to be more important. 4. In this internal conical joint, vertical and oblique loads were resisted mainly by the implant-abutment joint at the screw level and by the implant collar. Conclusively, It seems to be more important that how long the distance is from center of rotation of the implant itself to the resultant line of force from occlusal contact (leverage). In a morse taper implant, vertical and oblique loads are resisted mainly by the implant-abutment joint at the screw level and by the implant collar. This type of implant-abutment connection can also distribute forces deeper within the implant and shield the retention screw from excessive loading. Lateral forces are transmitted directly to the walls of the implant and the implant abutment mating bevels, providing greater resistance to interface opening.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.37-42
• /
• 1984

This paper deals with the characterics of the stability of uncontinuous plate structures with cracks. The relation between the J-intergal of the cracks existing in the stress-concentrated regions and local strain are investigated experimentally and theoretically. The BEM(boundary element method)analysis and test results lead to the follow conclusions: 1. A non-dimensional J was computed in a plate stress and strain condition for several kind of loads and crack types. The J design curves are defined as follows: J sub(E)/$\sigma$ sub(y) super(2) a=3.345(e/e sub(y) ) super(2) at e/e sub(y)$\leq$1 J sub(E)/$\sigma$ sub(y) super(2) a=3.345(e/e sub(y) ) at e/e sub(y)$\geq$1 2. Use of this curve provides a good estimation for the uncontinuous plate structures with cracks existing in the stress and strain concentrated region. 3. The stability of the characteristics is mainly depenent upon not the length of cracks but the type of the cracks.

• Journal of Biomedical Engineering Research
• /
• v.25 no.6
• /
• pp.489-496
• /
• 2004

Insertion of cannulae into vessels may disturb the blood flow doing non-physiological load and stress on blood cells such that ADP may increase and result in hemolysis. Authors used the computational method to simulate the 3-dimensional blood flow inside of the cannula using numerical method. We limited the research to within the drainage cannulae with side holes inserted through the human vein. In this paper, 9 different cannulae with side holes categorized by the number of side holes of 4, 12, and 20, and also categorized by the array type of side holes of staggered array, in-line array, and alternative in-line array were studied and compared to the cannula with no side holes by using CFD analysis. We evaluated the flow rate, the wall shear stress, and the shear rate and compared them with one another to estimate the effect of the side holes. The flow rate is not proportional to the number of the side holes. However, larger number of side holes can reduce the mean shear rate. Both the number and the array type of side holes play an important role on the fluid dynamics of the blood flow in cannulae.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.288-296
• /
• 2003

Generally, application of steel pipe pile as deep foundation member needs special requirement for the connection method between steel pipe pile and concrete footing. Even though two types of connection method are suggested in the related specification, type B-method is provident. To investigate real structural behavior of type B connection, several load tests are done with carefully designed experimental system. The purpose of this experiment is mainly focused on the understanding of actual behavior which can be predicted by design theory. At this research stage, vertical and lateral loading test are done for three types of specimen to review stress concentration, formation and behavior of imaginary RC column in the footing and effect of non-slip device installed in the steel pipe pile. The load resistance mechanism in these specific connection method is predicted based on both experimental results. The three-dimensional finite element modeling is also done for the purpose of comparison between numerical and experimental result. With all the results gained from experiment the structural behavior of imaginary RC column in the design concept is confirmed. The role of non-slip device is very important and it affects the resistance capacity with help of composite action of concrete and steel pipe pile.

• The Plant Pathology Journal
• /
• v.24 no.2
• /
• pp.191-201
• /
• 2008

Bacillus sp. SB-007 was isolated from pea leaves harvested from the southwestern parts of South Korea through screening on a minimal medium containing 0.2% purified cutin for its ability to induce the cutinase production. However, no cutinase was produced when it was grown in a minimal medium containing 0.2% glucose. A proteomic approach was applied to separate and characterize these differentially secreted proteins. The expression level of 83 extracellular proteins of the cutinase-producing Bacillus sp. strain SB-007 incubated in a cutinase-induced medium increased significantly as compared with that cultured in a non cutinase-induced medium containing glucose. The extracellular proteome of Bacillus sp. SB-007 includes proteins from different functional classes, such as enzymes for the degradation of various macromolecules, proteins involved in energy metabolism, sporulation, transport/binding proteins and lipoproteins, stress inducible proteins, several cellular molecule biosynthetic pathways and catabolism, and some proteins with an as yet unknown function. In addition, the two protein spots showed little similarities with the known lipolytic enzymes in the database. These secreted proteome analysis results are expected to be useful in improving the Bacillus strains for the production of industrial cutinases.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1997.10a
• /
• pp.7-7
• /
• 1997

During sintering of very porous green bodies, as obtained by compaction of hard powders - such as tungsten carbide or ceramics - or by injection moulding, important shrinkage occurs. Due to heterogeneous green density field, gravity effects, friction on the support, thermal gradients, etc., this shrinkage is often non-uniform, which' may induce significant shape changes. As the ratio of compact dimension to powder size is very high, the mechanics of continuum is relevant to model such phenomena. Thus numerical techniques, such as the finite element method can be used to simulate the sintering process and predict the final shape of the sintered part. Such type of simulation has much been developed in the last decade firstly for hot isostatic pressing and next for die compaction. Finite element modelling has been recently applied to free sintering. The simulation of sintering should be based on constitutive equations describing the thermo-mechanical behaviour of the material under any state of stress and any temperature which may arise within the sintering body. These equations can be drawn either from experimental data or from micromechanical models. The experiments usually consist in free sintering and sinter-forging tests. Indeed applying more complex loading conditions at high temperature under controlled atmosphere is delicate. Micromechanical models describe the constitutive behaviour of aggregates of spheres from the deformation of two-sphere contact either by viscous flow or grain boundary diffusion. Such models are not able to describe complex microstructure and mechanisms as observed in real materials but they can give some basic information on the formulation of constitutive equations. Practically both experimental and theoretical approaches can be coupled to identify the constitutive equations. Such procedure has been performed for modelling the sintering of compacts obtained by die pressing of a mixture of tungsten carbide and cobalt powders. The constitutive behaviour of this material during sintering has been described by a linear viscous constitutive model, whose functions have been fitted from results of free sintering and sinter-forging experiments. This model has next been introduced in ABAQUS finite element code to simulate the sintering of heterogeneous green compacts of various geometries at constant temperature. Examples of simulations are shown and compared with experiments.