• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.7
• /
• pp.741-746
• /
• 2004

Agglomerated and non-agglomerated SiO$_2$ particles are synthesized in a furnace by oxidation of TEOS vapor. These polydispersed particles are classified with DMA to extract particles. Then these particles are introduced into a thermal precipitator through the ESP(Electrostatic Precipitator) to investigate the themophoretic particle deposition using CNCs(Condensation Nuclei Counter). The efficiency of themophoretic particle deposition according to agglomerated and non-agglomerated particles in the thermal precipitator has been studied as a function of particle size and TEOS mole concentration using monodisperse particles classified by DMA. The results show that the particle deposition efficiency decreases as TEOS mole concentration increases and particle size increases. Thereffre, it is concluded that the thermophoretic deposition efficiency is dependent of the particle morphology.

• Journal of the Korean Ceramic Society
• /
• v.46 no.3
• /
• pp.249-252
• /
• 2009

Nanocrystalline ceria particles were prepared by using the ultrasonic spray pyrolysis method. The prepared ceria particles were found to be spherical and non-agglomerated by the SEM and TEM analyses. It was found that carrier gas influences the size and morphology. It was found that the air stream of carrier gas results in porous agglomerated structure of ceria abrasives, whereas solid nano-sphere can be obtained in a more oxidizing atmosphere.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.2
• /
• pp.207-217
• /
• 2015

The influence of powdered and colloidal nano-silica (NS) on the mechanical properties of cement mortar has been investigated. Powdered-NS (~40 nm) was synthesized by employing the sol-gel method and compared with commercially available colloidal NS (~20 nm). SEM and XRD studies revealed that the powdered-NS is non-agglomerated and amorphous, while colloidal-NS is agglomerated in nature. Further, these nanoparticles were incorporated into cement mortar for evaluating compressive strength, gel/space ratio, portlandite quantification, C-S-H quantification and chloride diffusion. Approximately, 27 and 37 % enhancement in compressive strength was observed using colloidal and powdered-NS, respectively, whereas the same was up to 19 % only when silica fume was used. Gel/space ratio was also determined on the basis of degree of hydration of cement mortar and it increases linearly with the compressive strength. Furthermore, DTG results revealed that lime consumption capacity of powdered-NS is significantly higher than colloidal-NS, which results in the formation of additional calcium-silicate-hydrate (C-S-H). Chloride penetration studies revealed that the powdered-NS significantly reduces the ingress of chloride ion as the microstructure is considerably improved by incorporating into cement mortar.

• Journal of the Korean Ceramic Society
• /
• v.35 no.10
• /
• pp.1078-1084
• /
• 1998

lanthanum chromite(LaCrO3) powder was synthesized by the combustion of a solution of metal nitrates La(NO3).6H2O and Cr(NO3)3.9H2O and urea. The pH of solution affected a yield of the combustion products but did not influence the morphology of the products. When the pH of the solution was in the range of 0.7-4, the yield of the combustion products was more than 90% The morphology of the combustion products was af-fected by heating methods for the solution. The hot-plate induced heating of the solution yielded powders hav-ing two-dimensionally interconnected agglomerates whereas microwave-induced heating produced a fine and non-agglomerated powders. The specific surface area(BET) of the combustion products using microwave-in-non-agglomerated powders. The specific surface area(BET) of the combustion products using microwave-in-duced heating method were larger(25~32m2/g) than that of hot plate heating method(10-14m2/g)

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.180-185
• /
• 2000

Nano crystalline or non-crystalline particles have been widely used in various industrial area, such as ceramics, catalysis, electronics, metallurgy and optic device. In all applications, synthesizing the particles as small as possible and controlling the crystalline phase according to its purpose are necessary for the enhancement of processing performance. In some cases, non-agglomerated particles may be necessary for solving the packing problems. This motivates our attempt of controlling size, morphology, phase of nano titania and silica particles. If one can enhance sintering rate of small aggregates independently of collision rate, one may expect that original aggregates can be changed into volume equivalent spheres and thereby the decrease of collision frequency due to the change leads to much smaller rate of growth of the particles. This is the basic idea of our control strategy.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.445-451
• /
• 2016

It is very important to obtain non-agglomerated nano particle state for practical application of nano technology. In order to improve the functionality of products using nano particles, more precise control of particle size distribution is required in their synthesis process. However, synthesized nano particles are agglomerated easily due to physical and chemical reasons, and it then veils unique properties of the nano particles and causes some troubles in their practical application. In this study, a separation method for nano particles from suspension by using the droplets as the separation space was proposed. Using the suspension of 0.002 wt. % with $TiO_2$ powder, the particle size distribution of nano particles in the recollected suspension was measured. From the results, it was confirmed that it is possible to separate and to recollect the nano particles monodispersed by using the suggested method.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.131-137
• /
• 1998

A composite copper coated powder was generated by pressure hydrogen stripping copper from Kelex 100 solvent extractant in the presence of silica powder. Within the limitation of solvent extraction under constant conditions, both loading level and stripping rate were reproducible. The stripping copper kinetics are reduced from a divalent state to a metallic state and then deposited on the surface of the silica powder. Copper nucleates heterogeneously on the seed particles. They are giving an agglomerated and non - uniform powder.

• Journal of the Korean Ceramic Society
• /
• v.29 no.12
• /
• pp.919-925
• /
• 1992

Continuous synthesis process for monodispersed zirconia powders with ultrasonic wave mixing was developed. Reactant solutions were flowed through a T-tube with small diameter and then mixed in a microscale with ultrasonification. Reaction and aging were followed during the mixed solution of reactants is in plug flowing through a narrow long teflon tubing. Zr(n-OC4H9)4 in ethanol and H2O in ethanol were used as reactants. From this process monodispersed, spherical, non-agglomerated, singlet hydrated zirconia powders with 0.6 $\mu\textrm{m}$ average size were obtained. Geometrical standard deviation of the particle size distribution was less than 1.2 with ultrasonic mixing, and the geometrical standard deviation was not affected by the flow rate of the reactants.

• Journal of Powder Materials
• /
• v.10 no.5
• /
• pp.310-317
• /
• 2003

Two-component ceramic (alumina-zirconia) composites were fabricated by a soft-solution process in which polyethylene glycol (PEG) was used as a polymeric carrier. Metal salts and PEG were dissolved in ethyl alcohol without any precipitation in 1:1 volume ratio of alumina and zirconia. In the non-aqueous system, the flammable solvent made explosive, exothermic reaction during drying process. The reaction resulted in formation of volume expanded, porous precursor powders by a vigorous decomposition of organic components in the precursor sol. The PEG content affected the grain size of sintered composites as well as the morphology of precursor powders. The difference of microstructure in sintered composite was attribute to the solubility and homogeneity of metal cations in precursor sol. At the optimum amount of the PEG polymer, the metal ions were dispersed effectively in solution and a homogeneous polymeric network was formed. It made less agglomerated particles in the precursor sol and affected on uniform grain size in sintered composite.

• Journal of Powder Materials
• /
• v.9 no.5
• /
• pp.346-351
• /
• 2002

Pure and fine, two-component titanate powders (barium titanate, calcium titanate etc.) were synthesized by an ethylene glycol method. Titanium isopropoxide and other metal ionic salts were dissolved in liquid-type ethylene glycol without any precipitation. In non-aqueous system, the amount of ethylene glycol affected the solubility and homogeneity of metal cation sources in the solution. At the optimum amount of the polymer, the metal ions were dispersed effectively in solution and a homogeneous polymeric network was formed. Most of the synthesized powders had sub-micron or nano-size primary particles after calcination and the agglomerated calcined powders were easily ground by ball milling process. All synthesized titanate powders had stable crystallization behavior at low temperature and high specific surface area after ball milling. The crystallization behavior and the microstructures of the calcined powders were affected on the ethylene glycol content.