• Journal of KSNVE
• /
• v.6 no.6
• /
• pp.749-754
• /
• 1996

In this paper, a design method of matching layers is presented for the sandwich type broad band underwater acoustic vibrators. The characteristic impedances of matching layers are determined to be matched to the characteristic impedance of head mass material. For the dynamic characteristic analysis of the sandwich type transducers, one dimensional FEM technique is also introduced. A test vibrator with the quarter wave matching layers has been designed to verify the proposed method. And the wide band characteristics of the input impedance and transmitting voltage response (TVR) are investigated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.2
• /
• pp.172-178
• /
• 2016

The location template matching (LTM) method is a technique of identifying an impact location on a structure, and is often applied to structural health monitoring and large scale human-computer interface (HCI) systems. The LTM method utilizes a certain measure of similarity between two time signals. The correlation coefficient is most widely used for this purpose, and the group delay based method is recently proposed to improve the accuracy of finding the best matching pair of signals. In practice, one of key essential consideration for implementing the LTM method is to guarantee that a sufficient number of vibration modes must be contained in the measured signal, and yet the lower sampling rate is needed for a real-time implementation. In this paper, the properties of correlation coefficient and group delay with respect to the number of vibration modes are investigated. A few important results are obtained through extensive computer simulations and experiments. If the number of vibration modes contained in the measured signal is more than four it is sufficient for the correlation based LTM method, while the group delay based LTM method requires smaller number of vibration modes.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.3-6
• /
• 2007

In this paper, a hybrid dual band LNA(Low Noise Amplifier) with a tunable matching circuit using varactor is designed for 433MHz and 912MHz RFID reader. The operating frequency is controlled by the bias voltage applied to the varactor. The measured results demonstrate that S21 parameter is 16.01dB and 10.72dB at 433MHz and 912MHz, respectively with a power consumption of 19.36mW. The S11 are -11.88dB and -3.31dB, the S22 are -11.18dB and -15.02dB at the same frequencies. The measured NF (Noise Figure) is 15.96dB and 7.21dB at 433MHz and 912MHz, respectively. The NF had poorer performance than the simulation results. The reason for this discrepancy was thought that the input matching is not performed exactly and a varactor in the input matching circuit degrades the NF characteristics.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.155-160
• /
• 2001

Actual engineering structure is frequently very complex, and parts of structure are designed independently by different engineers. Also each structure contains so many degree of freedom. For these reason, methods have been developed which permits the structure to be divided into components or substructures, with analysis being done on a small substructure in order to obtain a full structural system. In such case, because of different mesh size among finite element model (FEM) or different matching points among FEM models and experimentally obtained models, their interfacing points may be non-matching. Solving this non-matching problem is useful to other application such as structural dynamic modification or model updating. In this work, virtual node concept is introduced. Lagrange multipliers are used to enforce the interface compatibility constraint, and interface displacement is approximated by polynomial presentation. The governing equation of whole structure is derived using hybrid variational principle. The eigenvalue of whole structure are calculated using the determinant search method. The number of degree of freedom in the eigenvalue problem can be drastically reduced to just the number of interface degree of freedom. Some numerical simulation is performed to show usefulness of synthesis method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.666-671
• /
• 2002

For a large structure, substructure based SDM(structural dynamics modification) method is very effective to raise its dynamic characteristics. Dividing into smaller substructures has a major advantage in the aspect of computation especially for getting sensitivities, which are in the core of SDM process. But quite often, non-matching nodes problem occurs in the process of synthesizing substructures. The reason is that, in general, each substructure is modelled separately, then later combined together to form a entire structure model under interface constraint conditions. Without solving the non-matching nodes problem, the substructure based SDM can not be processed. In this work, virtual node concept is introduced. Lagrange multipliers are used to enforce the interface compatibility constraint. The governing equation of whole structure is derived using hybrid variational principle. The eigenvalues of whole structure are calculated using determinant search method. The number of degrees of freedom of the eigenvalue problem can be drastically reduced to just the number of interface degree of freedom. Thus, the eigenvalue sensitivities can be easily calculated, and further SDM can be efficiently performed. Some numerical problems are tested to show the effectiveness of handling non-matching nodes.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.2
• /
• pp.145-151
• /
• 2024

Recently, ship hull-mounted passive sonar system solution is needed in the perspective of improving target detection and elimination of vibration-induced noise. Our research team suggests acousticvibration matching method using front and rear signal of a sensor as the improvement of the problem above. Thus in this paper, theoretical background about matching method and its application on finite element method based multi-physics simulation are described. Furthermore, it is shown that target detection and hull vibration performance are improved by using matching method under the condition of our sensor system. Finally, practicality and future research are discussed.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.112-116
• /
• 2005

This paper presents a broadband two-stage low noise amplifier(LNA) operating from 3 to 10 GHz, designed with 0.18 ${\mu}m$ RF CMOS technology, The cascode feedback topology and broadband matching technique are used to achieve broadband performance and input/output matching characteristics. The proposed UWB LNA results in the low noise figure(NF) of 3.4 dB, input/output return loss($S_{11}/S_{22}$) of lower than -10 dB, and power gain of 14.5 dB with gain flatness of $\pm$1 -dB within the required bandwidth. The input-referred third-order intercept point($IIP_3$) and the input-referred 1-dB compression point($P_{ldB}$) are -7 dBm and -17 dBm, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.277-284
• /
• 2012

In this paper, we analyzed various noise in the video stream system that have largely influence on EMI noise. We presented the remedy for these various noises and then designed the wireless video streaming system for a vehicle. To minimize EMI noise, we derived the improvement of noise characteristic from impedance matching, new design of the inner layer of the PCB line design and new design of high-speed data Interfaces. As a result, the final system showed 40[dBuV/m] and 47[dBuV/m] dB in the each regulation band.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.2-61
• /
• 2006

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.2
• /
• pp.105-110
• /
• 2015

This paper relates with the eualization performance of Constellation Matching-MMA (CM-MMA) in order to the consists of optimum receiver for the minimization of intersymbol interference and additive noise effects that is occurs in the nonlinear communication channel. The error signal were obtained that combines the Constellation Matching technique that inserts the zero point between the signal point of equalizer for improving the residual isi and convergence speed compared to the currently used MMA algorithm. In the initial state of adaptive equalization, it depends on the MMA characteristics mainly. And in the steady state, it depends on the CM characteristics mainly. In order to analyzing the equalization performance, the output signal constellation, residual isi, maximum distortion, MSE and SER were applied, then it were compared with the present MMA algorithm. As a result of computer simulation, the CM-MMA has more better performance in the every performance index, and it was also confirmed that the constellation matching effect can be obtained in the greater than 20dB signal to noise ratio.