• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.216-224
• /
• 2009

The endless scaling down of the semiconductor process made the impact of the power network noise on the performance of the state-of-the-art chip a serious design problem. This paper compares the performances of two popular circuit reduction approaches used to improve the efficiency of power network noise analysis: moment matching-based model order reduction (MOR) and node elimination-based MOR. As the benchmarks, we chose PRIMA and R2Power as the matching-based MOR and the node elimination-based MOR. Experimental results indicate that the accuracy, efficiency, and memory requirement of both methods very strongly depend on the structure of the given circuit, i.e., numbers of the nodes and sources, and the number of moments to preserve for PRIMA. PRIMA has higher accuracy in general, while the error of R2Power is also in the acceptable range. On the other hand, PRIMA has the higher efficiency than R2Power, only when the numbers of nodes and sources are small enough. Otherwise, R2Power clearly outperforms PRIMA in efficiency. In the memory requirement, the memory size of PRIMA increases very quickly as the numbers of nodes, sources, and preserved moments increase.

• International Journal of Highway Engineering
• /
• v.17 no.5
• /
• pp.19-24
• /
• 2015

PURPOSES : The noise, which is typically generated by fast moving vehicles, can be intercepted by installing a noise barrier with a soundproof panel. However, reflections from the panels cause secondary noise, and hence lower the effectiveness of the panels. In this study, the reduction of reflection noise by considering the shape, especially zigzag one, of the soundproof panel have been evaluated. METHODS : The simulation model used in this study was Nord2000, which simulates real-road situations effectively. Based on the simulation results, the joining angle of $133^{\circ}$ with the pattern width (a) equal to 2 m and the projection height (b) equal to 0.5 m was adapted in the zigzag shape as the best profit designing factors. RESULTS: The measuring results at middle height, 15 m showed reduction at all points except the point with average -1.6 dB. At a greater height of 30 m, 2 points showed reduction. A real-sized facility was constructed to investigate the reflected sound from a zigzag shaped panel up to the height of 5 m. CONCLUSIONS: The reduction effects were detected in all the receive points in the range of 2-6 m distances and 1-5 m heights comparing the plane panel. Compared to plane panel, the noises are reduced at an average of 2.4 dBA.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.5
• /
• pp.687-693
• /
• 2000

Recently, a scroll compressor is widely used, because a scroll compressor features low noise, due to less pulsation of gas pressure, than that of the rotary compressor. The major source of noise in air-conditioner is a compressor. Therefore, noise reduction in a compressor is quite significant as an element technology in air-conditioner field. For a reduction of noise, the source of noise must be identified. This paper presents detailed analyzes for the major noise source (fluid-borne noise and structure-borne noise) causes in a scroll compressor, which will make possible a low noise and vibration design of a scroll compressor.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1891-1895
• /
• 2003

Switch-mode power supplies (SMPS) have become a major source of conducted electromagnetic interference (EMI) which is the combination between differential mode (DM) noise and common mode (CM) noise. This paper presents the conducted EMI reduction approach in flyback switched mode power supply by rerouting for circuit balance to reduce common mode noise. And differential mode noise can be reduce by adding $c_x$ capacitor across the input power line, and passive element to the gate drive of switching device MOSFET to slow down the switching times. This combination of our approach is the effective way to reduce the conducted EMI and it is also a cost effective for product design

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.128-132
• /
• 2008

The noise levels and individual employee noise exposure levels within a factory will determine the need for hearing conservation program. The difficulty in not having an effective hearing conservation program is the risk of hearing loss that employees may sustain. In the last few years the claims for hearing loss compensation have grown due to class action litigation brought against the employer and companies that have equipment in the factory alleged to have caused hearing loss. The Blower in the factory generates the noise of 98.3dB(A) in the frequency range of 2,000Hz, which may cause occupational hearing loss. By designing close type enclosures which are made of absorption material, about 24.4dB(A) reduction has been in the factory. It is demonstrated that this kind of enclosures can be effectively used to reduce the noise in the factory.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.6
• /
• pp.117-122
• /
• 2017

Cabin noise due to the electric powertrain of electrical vehicle may consists of motor noise caused by electrical mismatch and gear noise coming from reduction gearbox. These sound may be considered rather small noise compared to those of internal combustion engine, but without masking effect, the noise can be more annoying for customer. Thus, this paper demonstrates the characteristics of electrical vehicle powertrain noise, and the effect of passive damping material for the noise reduction. The typical motor noise can be affected by the motor torque. Also, it is demonstrated that the reduction gearbox may be a weak point for the noise path compared to the motor housing. With vehicle test, it is shown that the damping patch is more effective for noise reduction with deceleration condition than with acceleration condition.

• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.75-82
• /
• 2007

This paper presents practical work on the reduction of gear whine noise. In order to identify the source of the gear whine noise, transfer paths are searched and analyzed by operational deflection shape analysis and experimental modal analysis. It was found that gear whine noise has an air-borne noise path instead of structure-borne noise path. The main sources of air-borne noise were the two global modes caused by the resonance of an axle system. These modes created a vibro-acoustic noise problem. Vibro-acoustic noise can be reduced by controlling the vibration of the noise source. The vibration of noise source is controlled by the modification of structure to avoid the resonance or to reduce the excitation force. In the study, the excitation force of the axle system is attenuated by changing the tooth profile of the hypoid gear. The modification of the tooth profile yields a reduction of transmission error, which is correlated to the gear whine noise. Finally, whine noise is reduced by 10 dBA.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.117-123
• /
• 2003

This paper deals with pressure ripple and noise reduction characteristics for a hydrostatic transmission(HST) consisting of a variable axial piston pump connected in an open loop to a fixed displacement axial piston motor. Pressure ripples in HST is major source of vibration, which can lead to fatigue failure of components and cause noise. In order to reduce the pressure ripple, an annular tube type hydraulic filter proposes to absorb pressure ripples with the high frequencies components to achieve better noise attenuation in HST. The basic principle tube is applied to propagation of pressure wave, reflection, absorption in cross section of discontinuity and resonance in the hydraulic pipeline. It is experimently confirmed that a hydraulic filter is absorbed to be about 30∼40dB of pressure ripple with high frequencies. These results will assist in modeling and design of noise reduction in hydraulic control systems, and here, should provide a means of designing a quieter HST.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.6
• /
• pp.91-96
• /
• 2008

As a remarkable reduction of the vehicle noise, the important of tire noise which is generated from the vehicle and the necessity of the research for the noise reduction is being emphasized. In this study, the road noise which is excited by the interaction between tire and road has been studied. The subjective test(feeling test) according to SAE J1060 rating scale is applied to the evaluation of the road noise. The combination of the several tires and vehicles are made to consider the effect of the vehicle suspension and the tire structure for road noise. The vehicles with 3-different suspension system are applied to road noise test and the eight kinds of tires are selected. As the results, the effects of the vehicle suspension and tire structure which affects on road noise are investigated.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.506-510
• /
• 2005

This study shows work on the properties of noise and vibration in Whirlpool bath and plan for its reduction. Totally through 3 steps. we found out the properties of noise and vibration. various anti-vibration design for an effeciency test is conducted. By Anti-vibration for the pump causing vibration, about 4dB(A) was reduced. Moreover. by anti-vibration construction fixing the bathtub frame. about 3db(A) could be reduced. In the case of anti-vibration construction about the wall around the bathtub. and spreading damping paint on the bathtub. the noise was reduced.