• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.3
• /
• pp.288-293
• /
• 2009

This study presents the active noise control of duct noise. The duct was excited by a steady-state harmonic and white noise force and the control was performed by one control speaker attached to surface of the duct. An adaptive controller based on filtered x LMS(FXLMS) algorithm was used and controller was defined by minimizing the square of the response of the error microphone. The assemble controller, which is called a hybrid ANC(active noise control) system, was combined with feedforward and feedback controller. The feedforward ANC attenuates primary noise that is correlated with the reference signal, while the feedback ANC cancels the narrowband components of the primary noise that are not observed by the reference sensor. Furthermore, in many ANC applications, the periodic components of noise are the most intense and the feedback ANC system has the effect of reducing the spectral peaks of the primary noise, thus easing the burden of the feedforward ANC filter.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.4
• /
• pp.310-318
• /
• 2016

This study deals with a method to localize a noise source occuring in a marine vehicle in a 3D environment. Even when access to the noise source is limited for a marine vehicle, such as a ship or a submarine in operation, the signal received on a hydrophone located elsewhere contains Doppler effected noise by moving relatively. This study suggests noise localization algorithm in 3D based on Doppler effect by moving marine vehicle. Using a known source mounted on the vehicle, the noise source was estimated by reducing the range of Doppler center and closest point of approach via the least square method. The algorithm was verified through various simulations and it was shown that the noise could be localized in 3D based on Doppler effect by employing two fixed hydrophones located at the vehicle's exterior points and a known reference signal generator located somewhere on the vehicle.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.103-110
• /
• 2016

PURPOSES: In this paper, the effectiveness of speed-maintained standardization in road geometry on environmental impact at a downward slope location, based on greenhouse gas (GHG) emission indicators, was studied. Specifically, the aim of this study was to ascertain whether speed-maintained standardization resulted in decreased $CO_2$ emissions as well as noise pollution, due to reduced vehicle speeds. METHODS : In this study, speed-maintained standardization in road geometry was proposed as a means to reduce vehicle speeds, with a view to reducing $CO_2$ emissions and noise pollution. This technique was applied at a downward slope location. The vehicle speeds, $CO_2$ emissions, and noise levels before and after application of speed-maintained standardization were compared. RESULTS: It was found that speed-maintained standardization was effective as a means to reduce speed, as well as $CO_2$ emissions and noise pollution. By applying speed-maintained standardization, it was confirmed that vehicle speeds were reduced consistently. As a result, $CO_2$ emissions and noise levels were decreased by 9% and 11%, respectively. CONCLUSIONS : This study confirmed that speed-maintained standardization in road geometry is effective in reducing vehicle speeds, $CO_2$ emissions, and noise levels. Moreover, there is further scope for the application of this method in the design of roads in urban and rural areas, as well as in the design of highways.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.11a
• /
• pp.123-134
• /
• 2000

In this study, adapted Turbo Coding Algorithm for reducing communication error of fire detection system for marine vessels, especially image transmission. and proposed decoding speed increasing method of Turbo Coding Algorithm. The results are as follows : 1) Confirmed that a Turbo Code is so useful methods for reducing communication error in lots of noise environments. 2) Proposed technology in this study of speed increasing method of Turbo Coding Algorithm proved 2 times speed up effect than normal Turbo Code and communication error reducing as well in the board made by VHDL software & chips of ALTER Company.

• Journal of KSNVE
• /
• v.3 no.4
• /
• pp.325-330
• /
• 1993

The longitudinal vibration of the tape in the tape transport system influences the performance of the nagnetic tape-recording system. Generally it is controlled by a passive method with impedance roller which is easy to implement and cost-effective. Therefore the effect of the impedance roller in reducing the tape vibration was analyzed in this paper. The practical tape transport system was modelled mathematically as a mass-spring system. Both simulation and experimental study were carried out in order to show the vibration reduction effect of the impedance roller.

• Journal of the Society of Disaster Information
• /
• v.8 no.1
• /
• pp.27-35
• /
• 2012

The main objective of this paper is to evaluate the field applications and the noise reductions of micro surfacing pavement, which is often used to reduce environmental problems. A traffic noise mechanism was analyzed and a modified mix design method was proposed for nighttime constructions. Results on noise measurements using the statistical pass-by method showed noise reductions of 2.0 to 7.1 dB were observed. In addition, results on noise measurements using the close proximity method demonstrated that noise reductions of 5.6 to 6.7 dB were recorded under vehicle speed of 80km/h. The noise measurements revealed that the close proximity method was more stable than the statistical pass-by method. As a result, the effect of micro surfacing pavement on noise reductions was proved through the research. It is considered that the micro surfacing pavement method could be used as a preventive maintenance method and a comfortable noise reducing pavement technique.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1463-1466
• /
• 2007

Visco-elastic damping material for reducing heavy-weight floor impact noise and vibration in reinforced concrete structures was tested according to its thickness in the damping layer. The effect of damping material was compared with 20, 15, 10 and 5mm thickness. The wave propagation characteristics was measured for suggestion of an efficient method to reduce the floor impact noise. The method was proposed using the flexural wave propagation characteristics. The result showed that reduction of the thickness of damping layer made a slight difference; the natural frequency moved to higher frequency and the amplitude increased at low frequencies with 5mm thickness of damping material.

• Journal of the Korea Computer Industry Society
• /
• v.8 no.2
• /
• pp.81-88
• /
• 2007

The dissertation which it sees in communication the noise . it will be able to occur confirms the effect which it gives to this videotex and it the Nagao filter it will be able to reduce a noise in one original videotex which is possible and nearly it analyzes the Nagao filter of existing compared to compared to a different divided territory and for the efficiency which restores it sets the filter which is the possibility of reducing the MSE (Mean Square Error) it proposes simulation and the result it leads and the superiority of this method it confirms.

• Journal of Biomedical Engineering Research
• /
• v.28 no.6
• /
• pp.732-743
• /
• 2007

Background noise is one of the major complaints of not only hearing impaired persons but also normal listeners. This paper describes the results of two experiments in which speech recognition performance was determined for listeners with normal hearing and sensorineural hearing loss in noise environment. First, we compared speech enhancement algorithms by evaluation speech recognition ability in various speech-to-noise ratios and types of noise. Next, speech enhancement algorithms by reducing background noise were presented and evaluated to improve speech intelligibility for sensorineural hearing impairment listeners. We tested three noise reduction methods using single-microphone, such as spectrum subtraction and companding, Wiener filter method, and maximum likelihood envelop estimation. Their responses in background noise were investigated and compared with those by the speech enhancement algorithm that presented in this paper. The methods improved speech recognition test score for the sensorineural hearing impaired listeners, but not for normal listeners. The results suggest the speech enhancement algorithm with the loudness compression can improve speech intelligibility for listeners with sensorineural hearing loss.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.607-612
• /
• 2004

Disc brake noise continues to be a major concern throughout the automotive industry despite efforts to reduce its occurrence. Eliminating vibrations during braking is an important task for both vehicle passenger comfort and reducing the overall environmental noise levels. There are several classes of disc brake noise, the major ones being squeal, judder, groan, and moan. In this study, analytical model for moan noise of rear disk brake is investigated. Modeling of the disc brake assembly to take account of the effect of different geometrical and contact parameters is studied through the use of multi-body model. The contact stiffness of the caliper and torque member plays an important role in controlling brake vibration. Therefore, a suitable material pair at the caliper/body contact has been made. An ADAMS model of a rear disc brake system was integrated with a flexible suspension trailng arm from MSC/NASTRAN. A fully non-linear dynamic simulatin of brake system behavior, containing rigid and flexible bodies, was performed for a Prescribed set of operating conditions. Simulation results were validated using data from vehicle experimental testing.