• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.1
• /
• pp.1-6
• /
• 2002

Cogging torque is often a principal source of vibration and acoustic noise in high precision spindle motor applications. In this paper, cogging torque is analytically calculated using energy method to show that Fourier spectra of airgap permeance function and airgap MMF function are the most important design parameters to control cogging torque. To control these functions, stator pole shoe pairing and magnet arc design are proposed to minimize cogging torque. As for optimization technique, genetic algorithm is applied to handle trade-off effects of design parameters. Results show that the proposed method can reduce the cogging torque effectively.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.351-360
• /
• 2004

An optimal robust design methodology has been developed to minimize the warpage in a decorating panel of monitor molded by the plastic injection. For the associated methodology, the Taguchi's Design Of Experiment (DOE) based on orthogonal arrays and Signal-to-Noise Ratio is combined with commercial simulation tools f3r injection molding. An optimal robust design solution is statistically resulted from the computational simulation. The related experiment was done for evaluations of the warpage in the decorating panel part of monitor. This research showed that the warpage under the applied optimal design conditions was comparatively reduced.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.6
• /
• pp.417-426
• /
• 2006

A Digital X-ray imaging system using Compton backscattering has been developed to obtain a cross-sectional profile and mass loss of corroded lap-splices of aging aircraft from density variation. A slit-type camera was designed to focus on a small scattering volume inside the material, from which the backscattered photons are collected by a collimated scintillator detector for interpretation of material characteristics. The cross section of the lap-joint is scanned by moving the scattering volume through the thickness direction of the specimen. The mass loss of each layer has been estimated from a Compton backscatter A-scan to obtain the thickness of each layer including the aluminum sheet, the corrosion layer and the sealant. Quantitative information such as location and width of planar corrosion in the lap splices of fuselages is obtained by deconvolution using a nonlinear least-square error minimization method(BFGS method): A simple reconstruction model is also introduced to overcome distortion of the Compton backscatter data due to attenuation effects attributed to beam hardening and quantum noise.

• Journal of KSNVE
• /
• v.6 no.3
• /
• pp.305-315
• /
• 1996

Present paper aims at the correlation of modal characteristics of folding fin between test and analysis using an optimization theory. Folding fin is composed of a movable fin, a base fin, and many functional components related to the folding mechanism. Joint parts of folding fin in FEM are initially modeled as rigid elements resulting some difference between test and analysis in modal characteristics. Therefore, some equivalent springs representing joint parts are introduced to improve the FEM model. The springs were set as design variables, while the frequency difference between test and analysis was set as the object function. Bayesian procedure was ujsed for the minimization.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.795-805
• /
• 1999

Rubber mounts so called grommets and pipes are two major paths of vibration transmission from a compressor, an important vibration source in an air conditioner, to the whole unit. A procedure of configuring the suction and discharge pipes of the compressor was developed in this paper so as to reduce the vibration transmission through the pipes as well as the grommets. Through investigating the effects of shapes and connecting disrections of pipe elements on vibration transmission, a guideline to configure the pipe layout, which enables to reduce vibration transmission, was proposed. The initial pipe layout by the guideline was optimized with the objective function, minimization of boty vibration transmission and the cost, and with the constraints to yield the final dimensions of the pipes. The procedure not only minimizes the transmitted force to the circumferential devices but enables to eliminate rubber blocks or dampers, which are generally used to avoid resonances of the pipe system.

• Proceedings of the KOSOMBE Conference
• /
• v.1994 no.12
• /
• pp.131-133
• /
• 1994

뇌전위 측정에 의해 흥분 뉴런군의 위치를 추정하는 source localization problem은 Evoked Potential 해석법에 있어서 매우 중요한 의미를 갖는다. 이번 논문에서는 EEG실험에서의 전극 배치가 S/N(signal to noise ratio)과 추정 오차 사이에 어떤 영향을 미치는 가를 Monte Carlo 시뮬레이션으로 조사하였다. 머리 모델은 3중 구각 모델을 사용하였고 이론 이용하여 forward problem을 계산하였다. 쌍극자 파라미터를 minimization 하는 문제는 simplex method를 이용하여 계산하였다. 컴퓨터 시뮬레이션 결과, 특이한 점은 전극의 밀도와 입체각에 의해 쌍자 파라미터 오차가 변화했다는 사실이다. 이것은 곧바로 전극 배치와 연관이 된다. 실제 EEG 실험에서 전극 배치를 어떻게 했는가에 따라 그에 따른 오차가 변화한다. 이러한 오차의 원인을 제거하기 위해서 새로운 전극 배치를 모델링하여 기존의 전극 배치와 비교해 보았다. 그 결과 전극 밀도와 입체각에 대한 오차를 크게 줄일 수 있었다.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.349-352
• /
• 1997

The EEG amplifier satisfies high gain, high common mode rejection ratio(CMRR), high input impedance, low thermal drift, low noise and good d.c. performance. The Bipolar amplifier of this paper safisfies above categories and aim at minimization of the ESU(electric surgical unit) interference.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.10
• /
• pp.80-88
• /
• 1997

This paper describes a design of a Wavelet Adaptive Filter(WAF) for the removal of the baseline wandering and the minimization of the signal distortion using by wavelet transform and adaptive filter in the ECG signal. WAF consists of two parts. The first part is wavelet transform that decomposes the ECG signal into seven frequency bands using Vaidyanathan and Hoang wavelet. The second part is adaptive filter that uses the signal of seventh low frequency band among the wavelet transformed signals as primary input and a unit impulse sequence as reference input. For the evaluation of the performance of WAF, we used several baseline wandering elimination filters such as commerical standard filter with cutoff frequency of 0.5Hz and general adaptive filter. We made use of MIT/BIH database and real patient data for the evaluation. In conclusion, WAF showed a lower ST segement distortion than standard filter and adaptive filter and has a higher eliminated noise power than standard filter and adaptive filter.

• Economic and Environmental Geology
• /
• v.28 no.4
• /
• pp.433-438
• /
• 1995

The most popular minimization method is based on the least-squares criterion, which uses the $L_2$ norm to quantify the misfit between observed and synthetic data. The solution of the least-squares problem is the maximum likelihood point of a probability density containing data with Gaussian uncertainties. The distribution of errors in the geophysical data is, however, seldom Gaussian. Using the $L_2$ norm, large and sparsely distributed errors adversely affect the solution, and the estimated model parameters may even be completely unphysical. On the other hand, the least-absolute-deviation optimization, which is based on the $L_1$ norm, has much more robust statistical properties in the presence of noise. The solution of the $L_1$ problem is the maximum likelihood point of a probability density containing data with longer-tailed errors than the Gaussian distribution. Thus, the $L_1$ norm gives more reliable estimates when a small number of large errors contaminate the data. The effect of outliers is further reduced by M-fitting method with Cauchy error criterion, which can be performed by iteratively reweighted least-squares method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.8
• /
• pp.798-803
• /
• 2007

In case of minimized digital camera and mobile digital camera, it's difficult to get the high quality image by conventional AE(Auto Exposure) algorithm because of restriction of system organization. In this paper, a new algorithm that adopts a target setting, a compensation of feedback delay and a gamma correction, etc, are suggested for improving a noise increase and an output sensitivity decrease due to system minimization. We also suggest a method using fuzzy logic which can decide more effectively the ES(Electric Shutter) value and the AGC(Analog Gain Control) value than conventional system.