• Analytical Science and Technology
• /
• v.23 no.4
• /
• pp.383-388
• /
• 2010

Catalytic dissociation reaction was studied in order to transform waste plastics to oil by using noble metal supported catalysts. XRD, SEM, and GC/MSD analysis were performed to find the crystalline structure and shape, and product distribution. Generally, dissociation reaction occurs at low temperature compared to pyrolysis. Dissociation reaction has advantage of gasoline yield with respect to pyrolysis which products mainly $C_1\simC_4$. The result of dissociation reaction, gasoline was obtained much as a product. $C_5\simC_{11}$ compounds were produced as a gasoline product on Pt-zeolite among noble metal catalysts at $340^{\circ}C$. The conversion of dissociation reaction of waste plastics on the prepared catalyst was above 70% over $340^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.552-556
• /
• 2007

In this study, noble metals (Pd, Ru, Ir) were supported to $TiO_2$ catalyst. In order to distribute metals uniformly, $H_2O-H_2$ pretreatment technique was used. Xylene, toluene, and MEK were used as reactants. The monometallic or bimetallic catalysts were prepared by the excess wetness impregnation method and were characterized by XRD, and XPS analysis. Pd-Ru, Pd-Ir bimetallic catalysts had multipoint active sites which improved the range of Pd metal state. Bimetallic catalysts had a higher conversion of VOCs than that of monometallic one. The effect of $H_2O-H_2$ pretreatment technique was the enhancement of uniform distribution of Pd particles and promotion of catalytic efficiency. In this study, addition of Ru and Ir metals to Pd promoted oxidation conversion of VOCs. In addition, $H_2O-H_2$ pretreatment promoted removal efficiency of VOCs on the $TiO_2$ support.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.1
• /
• pp.51-59
• /
• 2011

Sulfur-Iodine (SI) cycle, which thermochemically splits water to hydrogen and oxygen through three stages of Bunsen reaction, HI decomposition, and $H_2SO_4$ decomposition, seems a promising process to produce hydrogen massively. Among them, the decomposition of $H_2SO_4$ ($H_2SO_4=H_2O+SO_2+1/2O_2$) requires high temperature heat over $800^{\circ}C$ such as the heat from concentrated solar energy or a very high temperature gas-cooled nuclear reactor. Because of harsh reaction conditions of high temperature and pressure with extremely corrosive reactants and products, there have been scarce and limited number of data reported on the pressurized $H_2SO_4$ decomposition. This work focuses whether the $H_2SO_4$ decomposition can occur at high pressure in a noble-metal reactor, which possibly resists corrosive acidic chemicals and possesses catalytic activity for the reaction. Decomposition reactions were conducted in a Pt-lined tubular reactor without any other catalytic species at conditions of $800^{\circ}C$ to $900^{\circ}C$ and 0 bar (ambient pressure) to 10 bar with 95 wt% $H_2SO_4$. The Pt-lined reactor was found to endure the corrosive pressurized condition, and its inner surface successfully carried out a catalytic role in decomposing $H_2SO_4$ to $SO_2$ and $O_2$. This preliminary result has proposed the availability of noble metal-lined reactors for the high temperature, high pressure sulfuric acid decomposition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.636-636
• /
• 2013

Since first discovery of strong Raman spectrum of molecules adsorbed on rough noble metal, surface enhanced Raman scattering (SERS) has been widely used for detection of molecules with low concentration. Surface plasmons at noble metal can enhance Raman spectrum and using Au nanostructures as substrates of SERS has advantages due to it has chemical stability and biocompatibility. However, the photoluminescence (PL) background from Au remains a problem because of obtaining molecular vibration information. Recently, graphene, two-dimensional atomic layer of carbon atoms, is also well known as PL quenchers for electronic and vibrational excitation. In this study, we observed SERS of single layer graphene on or under monolayer of Au nanoparticles (NPs). Single layer graphene is grown by chemical vapor deposition and transferred onto or under the monolayer of Au NPs by using PMMA transfer method. Monolayer of Au NPs prepared using Langmuir-Blodgett method on or under graphene surface provides closed and well-packed monolayer of Au NPs. Scanning electron microscopy (SEM) and Raman spectroscopy (WItec, 532 nm) were performed in order to confirm effects of Au NPs on enhanced Raman spectrum. Highly enhanced Raman signal of graphene by Au NPs were observed due to many hot-spots at gap of closed well-packed Au NPs. The results showed that single layer graphene provides larger SERS effects compared to multilayer graphene and the enhancement of the G band was larger than that of 2D band. Moreover, we confirm the appearance of D band in this study that is not clear in normal Raman spectrum. In our study, D band appearance is ascribed to the SERS effect resulted from defects induced graphene on Au NPs. Monolayer film of Au NPs under the graphene provided more highly enhanced graphene Raman signal compared to that on the graphene. The Au NPs-graphene SERS substrate can be possibly applied to biochemical sensing applications requiring highly sensitive and selective assays.

• Applied Chemistry for Engineering
• /
• v.35 no.2
• /
• pp.134-139
• /
• 2024

In the steam reforming of methane reactions, the effect of adding noble metals Ru and Pd to a Ni-based catalyst as promoters was analyzed in terms of catalytic activity and hydrogen production. The synthesized catalysts were coated on the surface of a honeycomb-structured metal monolith to perform steam methane reforming reactions. The catalysts were characterized by XRD, TPR, and SEM, and after the reforming reaction, the gas composition was analyzed by GC to measure methane conversion, hydrogen yield, and CO selectivity. The addition of 0.5 wt% Ru improved the reduction properties of the Ni catalyst and exhibited enhanced catalytic activity with a methane conversion of 99.91%. In addition, reaction characteristics were analyzed according to various process conditions. Methane conversion of over 90% and hydrogen yield of more than 3.3 were achieved at a reaction temperature of 800 ℃, a gas hourly space velocity (GHSV) of less than 10000 h^-1, and a ratio of H₂O to CH₄ (S/C) higher than 3.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.2
• /
• pp.139-146
• /
• 2000

Cavitation can occur in pipes when liquid is moving at high velocity, especially at pittings where the smooth bore of the pipe is interrupted. The effect is usually to produce pitting on the downstream side of the turbulence. However, stress corrosion cracking behavior under cavitation erosion-corrosion was neatly unknown. In this study, therefore, some were investigated of stress corrosion cracking behavior, others were stress corrosion cracking behavior under cavitation erosion-corrosion of water injection. And datas obtained as the results of experiment were compared between the two. Mainresult obtained are as follows: 1) Stress corrosion cracking growth rate of heat affected zone under cavitation erosion-corrosion becomes most rapid, and stress intensity factor $K_1$becomes most high. 2) Stress corrosion cracking growth mechanism by cavitation erosion-corrosion is judgement on the strength of the film rupture model and the tunnel model. 3) The range of potential as passivation of heat affected zone is less noble than that of base metal, and that value is smaller. 4) Corrosion potential under cavitation erosion-corrosion in loaded stress is less noble than that of stress corrosion, and corrosion current density is higher.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.2
• /
• pp.76-84
• /
• 1992

In this study, corrosion fatigue test of SAPH45 steel was performed by the use of plane behavior of base metal (BM) and heat affected zone (HAZ) of SAPH45. The main results obtained are as follows: 1) The more aspect ratio (b/t) of corner crack decreases, the more aspect ratio (b/a) takes greatly effect by corrosion. 2) The correlation between the stress intensity factor range ($\Delta$k) and crack growth rate (da/dN) for weldment in seawater is given by Paris rule as follow: da/dN=C($\Delta$K) super(m). Where m is constant, and the value is 3.82-3.84. 3) The accelerative factor ($\alpha$) of BM and HAZ under seawater is about 1.1-1.9, and ($\alpha$) of HAZ increases more and more under the low $\Delta$K region. 4) HAZ is more susceptible to corrowion than BM because of potential of electrode (E sub(c)) of HAZ becomes more less noble potential than that of BM.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.1
• /
• pp.19-24
• /
• 2001

A solvent sublation has been studied for the determination of trace Au(III), Pt(IV) and Pd(II) in waste water with their complexes of 2-mercaptobenzothiazole (MBT). Experimental conditions such as the concentration of HCl, the amount of MBT as a ligand, the type and amount of surfactants, bubbling rate and time, and the type of organic solvent were optimized for the solvent sublation, i.e., 25.0 mL of 2.0 M HCl solution and 30mL of 0.4%(w/v) MBT ethanolic solution were added to a 1.0 L sample to form stable complexes. The addition of 4.0 mL of 1 ${\times}$$10^{-3}$ M CTAB (cetyltrimehtylammonium bromide) solution was needed for the effective flotation accomplished by bubbling nitrogen gas at the rate of 40.0 mL/min for 35 minutes. As a solvent, 20.0 mL of MIBK (methylisobuthylketone) was used to extract the floated complexes. The procedure was applied to three kinds of waste waters. Au(III) was determined as 0.68 ng/mL and 0.98 ng/mL respectively for final washed water of two plating industries in Banwol. Pd(II) and Pt(IV) were not detected in any of the three samples. The recovery, which was obtained with analyte-spiked samples, were 95-120%.

• Toxicological Research
• /
• v.32 no.2
• /
• pp.95-102
• /
• 2016

In the recent years, noble nanoparticles have attracted and emerged in the field of biology, medicine and electronics due to their incredible applications. There were several methods have been used for synthesis of nanoparticles such as toxic chemicals and high energy physical procedures. To overcome these, biological method has been used for the synthesis of various metal nanoparticles. Among the nanoparticles, silver nanoparticles (AgNPs) have received much attention in various fields, such as antimicrobial activity, therapeutics, bio-molecular detection, silver nanocoated medical devices and optical receptor. Moreover, the biological approach, in particular the usage of natural organisms has offered a reliable, simple, nontoxic and environmental friendly method. Hence, the current article is focused on the biological synthesis of silver nanoparticles and their application in the biomedical field.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.356-359
• /
• 2005

Ionic-polymer-metal-composite(IPMC), one of new actuation materials of electroactive polymers plated with noble metallic electrodes is known for the fast bending upon electric field. The IPMC strip bends towards anode under electrical field. It has many merits of low driving voltage, quick responsiveness, high durability, possibility of miniaturizability. In this paper, we studied for developing the large deflection of IPMC according several fabricating parameters. We measured the large deflection by the different process of sandpaper and sandblasting in surface treatment, the initial compositing process and the surface electroding process, and the different counter ions in ion exchanging process. In fundamental, the displacement of IPMC strip depends on voltage magnitude and applied signal frequency and its maximum deformation is observed at a critical frequency, resonant frequency.