• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2002년도 추계학술발표논문집
• /
• pp.81-90
• /
• 2002

Air entrainment of a winding roll with a nip roller was studied numerically. The amount of air entrainment between two rotating rollers was obtained by solving lubrication equation, Reynolds equation, which neglect the existence of a web. However, the numerical model of this study included the web existence, therefore it considered the two lubricating air films between a winding roll and a web and also between a nip roller and the web. The pressure profiles and gap profiles of the two films were obtained by solving lubrication equation for the two air films and force balance equation of the web. Ballooning phenomenon was examined in terms of nip force, wrap angle, web stiffness, web speed, and web tension. This ballooning phenomenon caused by the back flow of the air film blocked by the nip roller. Air entrainment of the two numerical models was compared.

• 대한기계학회논문집A
• /
• 제30권10호
• /
• pp.1328-1334
• /
• 2006

In the rolling mills for sheet metal rolling, paper rolling and etc., the impurities of roller surface have crucial effects on the surface quality of the products obtained by rolling. The Roll Cleaner is a device to remove impurities on roller surface during a rolling operation. Nip Pressure means the line pressure interacted between the roll cleaner blade and the roller surface. The nip pressure is the most important parameter which decides the performance of roll cleaner, and it depends upon several factors including the cleaner design and its blade stiffness. This study, first, analyzes the mechanism of the nip pressure generation for a roll cleaner designed commercially, which is an crucial process for effective design of roll cleaners. Second, the technique for the measurement of nip pressure is developed, which is useful to verify the performance of roll cleaners and to setup them properly at factory floor.

• International Journal of Aeronautical and Space Sciences
• /
• 제9권1호
• /
• pp.137-146
• /
• 2008

Proper amount of entrained air and nip force should be also considered to minimize ballooning phenomenon since tight contact between a roller and web is required. In this paper, various web materials, PET(Polyester) and OPP(Oriented Poly Propylene) have been selected and investigated to satisfy high-speed printing requirement. Several web speeds, web tensions, and temperature conditions are imposed on each web materials and the pressure and gap profiles as well as nip force have been calculated. Increase of both the winding roller radius and the incoming wrap angle is considered under proper taper tension at 500 m/min of rewinding roller. By solving coupled Reynolds equation and web deflection equation simultaneously, the fluid-structure interaction process has been developed and is applied to the rewinding roller to investigate the ballooning phenomenon which causes guiding problems in high-speed printing performance conditions. By adjusting the linear taper tension, stress distribution between rewinding webs can be remarkably reduced and stable pressure and gap profile with ignorable ballooning phenomenon have been found.

• 한국안전학회지
• /
• 제18권2호
• /
• pp.22-27
• /
• 2003

The roller machines installed in the industrial field are operated under hazardous conditions due to no safety devices available, human error during operation, defective safety devices, and inadequate regulation even in case that safety devices are provided. Up to now, most roller machines installed in domestic field are provides with band breaking system as a safety device. In this study, the emergency stop distance is measured within the limit of domestic regulation but violates a foreign regulation(EN1417). Consequently, it is concluded that the roller machines with a band breaking system have high possibility of death or serious injury of the operator and the system should be improved with the introduction of additional safety devices. This thesis suggests the safety measures suitable for the roller machines with different drive systems based on the experiment results. The use of the newly developed safety system has been tested on many cases.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.30-37
• /
• 2004

This thesis develops a fuzzy-PID control algorithm for control the filament winding tension. It is developed by applying classical PID control technique to a fuzzy logic controller. It is composed of a fuzzy-PI controller and a fuzzy-D controller. The fuzzy-PI controller uses error and integrated error as inputs, and the fuzzy-D controller uses derivative of error as input. The fuzzy-PI controller uses Takagi-Sugeno fuzzy inference system, and the fuzzy-D controller uses Mamdani fuzzy inference system. The fuzzy rule base for the fuzzy-PI controller is designed using 19 rules, and the fuzzy rule base for the fuzzy-D controller is designed using 5 rules. A test-bed is set-up for verifying the effectiveness of the developing control algorithm in control the filament winding tension. It is composed of a mandrel, a carriage, a force sensor, a driving roller, nip rollers, a creel, and a real-time control system. Nip rollers apply a vertical force to a filament, and the driving roller drives it. The real-time control system is developed by using MATLAB/xPC Target. First, experiments for showing the inherent problems of an open-loop control scheme in a filament winding are performed. Then, experiments for showing the robustness of the developing fuzzy-PID control algorithm are performed under various working conditions occurring in a filament winding such as mandrel rotating speed change, carriage traversing, spool radius change, and reference input change.

• 한국인쇄학회지
• /
• 제23권2호
• /
• pp.129-141
• /
• 2005

The liquid film behavior between two rotating rollers has been analyzed for many years. Their contributions were, however, limited almost within the areas of polymer laminar flow in there. When the slip contact of two rotating rollers is used as a role of vehicle to distribute the liquid discharged on to each roller after splitting from the nip, there was few available relationship to control the roller speed and to design system. On this work it was possible to get out a certain relationship between the discharged film thickness ratio and the roller surface seeds without any help of pressure limit at the splitting point. The hydrodynamic analyzation of Newtonian liquid behavior around the point was well proved on some manipulative experiment. The thickness ratio increases along with the roll surface speed ratio increases. And the discharged volume flow rate ratio on each roller surface varies with square of the speed ratio. Both of these relationship have a decision factor also made up by the speed ratio.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1131-1140
• /
• 2011

A new rotary gravure-offset printing unit is constructed by paralleling a gravure plate cylinder, a blanket cylinder and a impression roller. A Muti-Unit Gravure-Offset Printing Press(MUGOP) equipped with a series of the 3 printing units is utilized for roll-to-roll fine printing. Its core technology is precise over-piling printing of fine patterns. The severe problems of 'slurring' and 'doubling' in typical offset printing are unavoidable, which can be eliminated by applying a soft pad-type blanket cylinder and the unique 'true rolling' technique. Nip pressure between the blanket cylinder and the plate cylinder is measured by the constant pressure control system which equipped with load cells attached on the cylinders' axes. The running circumference of the blanket cylinder is increased to reach the same circumference of the plate cylinder as the pressure increasing, so that the specifications of the blanket cylinder is determined by the relationships of its shore hardness, diameter and nip pressure. When a softer blanket is used, a blanket cylinder of smaller diameter could give higher nip pressure. Realization of the true rolling technique on the MUGOP makes multilayer printing possible as well as fine printing in printed electronics.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.241-245
• /
• 2004

Among the various manufacturing processes of composites, the tape lay-up process of thermoset prepreg has many advantages compared to autoclave or hot press forming. It has a high potential to process automation and continuous fabrication .. Fiber placement developed as a logical combination of filament winding and automated tape placement to overcome some of the limitations of each manufacturing method. Fiber placement uses a compaction device to apply direct contact between the incoming materials in the fiber placement head and Heat is added to the materials at the nip point of the compaction roller. This paper will discuss property of thermoset composite as compaction and heat effect in Automated fiber placement

• 대한기계학회논문집A
• /
• 제36권10호
• /
• pp.1255-1260
• /
• 2012

분말직송압연에 따른 티타늄 분말 집합체의 치밀화 거동을 연구하였다. 이와 관련하여 실험 시 나타나는 롤-밀림 현상을 분석하기 위한 이론적 모델을 개발하였으며, 이를 통해 보다 실질적인 유한요소 해석을 수행하였다. 개발된 롤-밀림 모델을 통해 공정변수에 따른 롤-밀림의 경향을 정량적으로 파악하였으며, 분말직송압연 공정의 유한요소 해석을 통해 판재의 위치 별 최종 상대 밀도를 비교적 정확히 예측할 수 있었다. 아울러 공정 시 분말집합체의 치밀화 현상을 이해하기 위해 분말-롤 간 접촉 압력 및 전단응력을 계산하였으며 이를 통해 분말의 물림현상이 나타나는 영역을 보다 명확히 확인할 수 있었다.