• 대한수의학회지
• /
• 제25권2호
• /
• pp.145-148
• /
• 1985

Nickel toxicity and interactions of nickel with zinc, copper, and lead were studied in glowing chicks fed supplemented diet. Feed intake and growth rate of the chick were reduced by 250mg nickel as a sulfate salt per kg of feed. The toxicity of nickel was decreased by zinc or copper supplementation, but not lead. High nickel feed increased nickel level in kidney and decreased zinc levels in tibia and plasma. However, low zinc levels in tibia and in plasma were reversed by zinc supplementation. Hemoglobin, packed cell volume, and aortic elastin content were increased in chicks fed nickel. These results suggest that nickel toxicity is induced by interference with zinc metabolism.

• 한국응용과학기술학회지
• /
• 제27권3호
• /
• pp.273-281
• /
• 2010

Nickel recovery method was studied by the wet process from the catalyst used in hydrogenation process. Nickel content in waste catalyst was about 16%. At the waste catalyst leaching system by the alkaline solution, selective leaching of nickel was possible by amine complex formation reaction from ammonia water and ammonium chloride mixed leachate. The best leaching condition of nickel from mixed leachate was acquired at the condition of pH 8. LIX65N as chelating solvent extractant was used to recover nickel from alkaline leachate. The purity of recovered nickel was higher than 99.5%, and the whole quantity of nickel was recovered from amine complex.

• 전기화학회지
• /
• 제13권4호
• /
• pp.270-276
• /
• 2010

기공 경사화된 마이크론 단위의 구조 틀 및 나노 수지상 구조 벽을 가지는 니켈-구리 거품 전극을 전기화학적인 방법으로 합성하였다. 전해 도금 시 순수한 니켈은 치밀한 층으로 성장하는 양상을 보였으나, 구리와 함께 도금시키는 경우 그 성장 양상이 순수한 니켈과는 매우 다르게 관찰되었다. 특히, 첨가제로써 염소 이온의 농도가 증가함에 따라 니켈-구리 도금 층의 수지상 성장이 뚜렷해지는 모습을 보였다. 또한, 기재와 먼 부분일수록 도금 층 내 구리 대비 니켈의 상대적인 양이 감소하였으며, 염소 이온 농도가 높아짐에 따라 전 도금 층에 걸쳐 니켈의 양이 증가하였다. 수지상 구조 벽의 가지 내부 조성을 분석한 결과, 중심부로 갈수록 구리 함량이 점차 높아지는 조성 구배를 확인하였으며, 적절한 열처리를 통해 상호 확산을 유도하여 균일한 조성의 니켈-구리 합금을 얻어낼 수 있었다. 본 연구를 통해 제작된 재료는 기능성 전기 화학 장치용 고성능 전극에 활용될 수 있을 것으로 기대된다.

• Corrosion Science and Technology
• /
• 제6권3호
• /
• pp.133-139
• /
• 2007

Nickel powder was coated with aluminum nitrate solution to increase the thermal stability of a porous nickel support and control the nickel content in the Pd-Cu-Ni ternary alloyed membrane. Raw nickel powder and alumina coated nickel powder were uniaxialy pressed by home made press with metal cylindrical mold. Though the used nickel powder prepared by pulsed wire evaporation (PWE) method has a good thermal stability, the porous nickel support was too much sintered and the pores of porous nickel support was plugged at high temperature (over $800^{\circ}C$) making it not suitable for the porous support of a palladium based composite membrane. In order to overcome this problem, the nickel powder was coated by alumina and alumina modified porous nickel support resists up to $1000^{\circ}C$ without pore destruction. Furthermore, the compositions of Pd-Cu-Ni ternary alloy membrane prepared by magnetron sputtering and Cu-reflow could be controlled by not only Cu-reflow temperature but also alumina coating amount. SEM analysis and mercury porosimeter analysis evidenced that the alumina coated on the surface of nickel powder interrupted nickel sintering.

• 한국표면공학회지
• /
• 제48권2호
• /
• pp.62-67
• /
• 2015

Nickel is a commercially important and versatile element in electroplating. The applications of nickel electroplating fall into three main categories: decorative, functional and electroforming. In decorative applications, electroplated nickel is most often applied in combination with electrodeposited chromium. Nickel is deposited on surfaces to improve corrosion and wear resistance or modify magnetic and other properties. Electroforming is electroplating applied to the fabrication of products of various kinds. Nickel is deposited onto a substrate and then removed from it to create a part made entirely of nickel. In this study, mechanical property of Ni electrodeposits in various manufacturing condition such as temperature, current density, pH and electrolyte content, was investigated to understand effect of electrolysis condition on mechanical property. Vickers hardness increased as the temperature and pH increased and current density and electrolyte content decreased and pH increased. The results were explained by cathode overvoltage and hydrogen evolution.

• Macromolecular Research
• /
• 제14권3호
• /
• pp.306-311
• /
• 2006

New unsymmetrical ($\alpha$-Diimine)nickel(II) catalysts having different pendent groups at the ortho positions on aromatic rings were synthesized and subjected to propylene polymerizations with MAO (methylaluminoxane). Structural analyses of the resulting polypropylenes by $^1H\;and\;^{13}C\;NMR$ showed that the ortho substituents on aromatic rings of ($\alpha$-diimine)nickel(II) catalyst affected significantly the polypropylene microstructure. While $C_s$ symmetric catalyst afforded a syndiotactic polypropylene (rr triad content=66%) due to the syndiospecific chain end control, $C_1$ symmetric catalysts produced much less stereoregular polypropylenes (rr triads content <50%), presumably because of collision of the isospecific site control with the syndiospecific chain end control.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.625-628
• /
• 1999

Recently. high-density printed circuit boards(PCB) become indispensable with the minaturization of components. Nickel is deposited on the copper patterns and followed by the gold deposition for improving connection reliability between the printed circuit boards and electronic components. Conventionally electrodeposition has been applied to metalization of copper patterns. However metalization by this method is not applicable for the isolated fine and concentrated patterns. Therefore, metalization technology of the fine patterns by electroless plating is required in place of electrodeposition. The application of electroless nickel plating for interconnection with solder strongly relies on the solderability and the interactions between nickel and solder. Factors such as phosphorus content of the deposit additive and bath temperature may influence solderability of the electroless nickel deposit. So solderability of electroless nickel/ gold deposits was investigated with substrates plated changing the condition of nickel solution.

• 한국재료학회지
• /
• 제30권4호
• /
• pp.184-196
• /
• 2020

In this study, effects of carbon and nickel on microstructure and low temperature Charpy impact properties of HSLA (high strength low alloy) steels are investigated. To understand the complex phase transformation behavior of HSLA steels with high strength and toughness before and after welding processes, three kinds of HSLA steels are fabricated by varying the carbon and nickel content. Microstructure analysis, low temperature Charpy impact test, and Vickers hardness test are performed for the base metals and CGHAZ (coarse-grain heat affected zone) specimens. The specimens with the lowest carbon and nickel content have the highest volume fraction of AF, the lowest volume fraction of GB, and the smallest GB packet size. So, the low temperature Charpy absorbed energy of the CGHAZ specimen is the highest. The specimens with increased carbon and nickel content have the lowest volume fraction of AF, the highest volume fraction of GB, and the largest GB packet size. So, the low temperature Charpy absorbed energy of the CGHAZ specimen is the lowest.

• Journal of Electrochemical Science and Technology
• /
• 제1권2호
• /
• pp.117-120
• /
• 2010

Materials used as fuel cell electrode should be light, high conductive, high surface area for reaction, catalytic surface and uniformity of porous structure. Nickel is widely used in electrode materials because it itself has catalytic properties. When used as electrode materials, nickel of only a few im on the surface may be sufficient to conduct the catalytic role. To manufacture the nickel with porous structure, Electroless nickel plating on carbon fiber be conducted. Because electroless nickel plating is possible to do uniform coating on the surface of substrate with complex shape. Acidic bath and alkaline bathe were used in electroless nickel plating bath, and pH and temperature of bath were controlled. The rate of electroless plating in alkaline bath was faster than that in acidic bath. As increasing pH and temperature, the rate of electrolee plating was increased. The content of phosphorous in nickel deposit was higher in acidic bath than that in alkaline bath. As a result, the uniform nickel deposit on porous carbon fiber was conducted.

• 대한금속재료학회지
• /
• 제48권1호
• /
• pp.62-70
• /
• 2010

Leaching and solvent extraction experiments have been performed to develop a hydrometallurgical process for the recovery of nickel and cobalt from nickel laterite ore with high magnesium content. Most of the nickel and magnesium in the laterite ore dissolved at leaching conditions of $80^{\circ}C$ and 100 g/L sulfuric acid concentration. while half of the cobalt and iron were leached at the same conditions. Solvent extraction experiments were carried out with D2EHPA and saponifed D2EHPA from a synthetic solution containing Ni, Co, and Mg. The extraction percentage of Co, Mg. and Ni by D2EHPA was very low in a pH range of 4.4 to 7.3. while the extraction percentage sharply increased by using saponified D2EHPA. The stripping percentage of the metals from the saponified D2EHPA increased with sulfuric acid concentration and reached 99.9% at 1 M $H_2SO_4$ solution.