• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.668-673
• /
• 2008

The objective of this study is to optimize the leaching conditions of sequential leaching and extracting processes for selective Ni recovery from spent Ni-Mo-based catalyst. The selective Ni recovery process consists of two processes of leaching and extracting process. In this 2-step process, Ni component is dissolved from solid spent Ni-Mo-based catalyst into leaching agent in leaching process and sequentially extracted to Ni complex with an extracting agent in the extracting process. The solutions of nitric acid ($HNO_3$), ammonium carbonate ($(NH_4)_2CO_3$) and sodium carbonate ($Na_2CO_3$) were used as a leaching agent in leaching process and oxalic acid was used as an extracting agent in extracting process. $HNO_3$ solution is the most efficient leaching agent among the various leaching agent. Also, the optimized leaching conditions for the efficient and selective Ni recovery were the leaching temperature of $90^{\circ}C,\;HNO_3$ concentration of 6.25 vol% and elapsed time of 3 h. As a result, Nickel oxalate having the highest yield of 88.7% and purity of 100% was obtained after sequentially leaching and extracting processes under the optimized leaching conditions.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.3
• /
• pp.19-23
• /
• 2007

The NiSi is very promising candidate for the metallization in 45 nm CMOS process such as FUSI(fully silicided) gate and source/drain contact because it exhibits non-size dependent resistance, low silicon consumption and mid-gap workfunction. Ni film was first deposited by using ALD (atomic layer deposition) technique with Bis-Ni precursor and $H_2$ reactant gas at $220^{\circ}C$ with deposition rate of $1.25\;{\AA}/cycle$. The as-deposited Ni film exhibited a sheet resistance of $5\;{\Omega}/{\square}$. RTP (repaid thermal process) was then performed by varying temperature from $400^{\circ}C$ to $900^{\circ}C$ in $N_2$ ambient for the formation of NiSi. The process temperature window for the formation of low-resistance NiSi was estimated from $600^{\circ}C$ to $800^{\circ}C$ and from $700^{\circ}C$ to $800^{\circ}C$ with and without Ti capping layer. The respective sheet resistance of the films was changed to $2.5\;{\Omega}/{\square}$ and $3\;{\Omega}/{\square}$ after silicidation. This is because Ti capping layer increases reaction between Ni and Si and suppresses the oxidation and impurity incorporation into Ni film during silicidation process. The NiSi films were treated by additional thermal stress in a resistively heated furnace for test of thermal stability, showing that the film heat-treated at $800^{\circ}C$ was more stable than that at $700^{\circ}C$ due to better crystallinity.

• Toxicological Research
• /
• v.26 no.2
• /
• pp.157-162
• /
• 2010

In this study, we investigated the atmospheric heavy metal concentrations in the particulate matter inside the subway stations of Seoul. In particular, we examined the correlation between the heavy metals and studied the effect of the heavy metals on cell proliferation. In six selected subway stations in Seoul, particulate matter was captured at the platforms and 11 types of heavy metals were analyzed. The results showed that the mean concentration of iron was the highest out of the heavy metals in particulate matter, followed by copper, potassium, calcium, zinc, nickel, sodium, manganese, magnesium, chromium and cadmium in that order. The correlation analysis showed that the correlations between the heavy metals was highest in the following order: (Cu vs Zn), (Ca vs Na), (Ca vs Mn), (Ni vs Cr), (Na vs Mn), (Cr vs Cd), (Zn vs Cd), (Cu vs Cd), (Ni vs Cd), (Cu vs Ni), (K vs Zn), (Cu vs K), (Cu vs Cr), (K vs Cd), (Zn vs Cr), (K vs Ni), (Zn vs Ni), (K vs Cr), and (Fe vs Cu). The correlation coefficient between zinc and copper was 0.937, indicating the highest correlation. Copper, zinc, nickel, chromium and cadmium, which are generated from artificial sources in general, showed correlations with many of the other metals and the correlation coefficients were also relatively high. The effect of the heavy metals on cell proliferation was also investigated in this study. Cultured cell was exposed to 10 mg/l or 100 mg/l of iron, copper, calcium, zinc, nickel, manganese, magnesium, chromium and cadmium for 24 hours. The cell proliferation in all the heavy metal-treated groups was not inhibited at 10 mg/l of the heavy metal concentration. The only exception to this was with the cadmium-treated group which showed a strong cell proliferation inhibition. This study provides the fundamental data for the understanding of simultaneous heavy metal exposure tendency at the time of particulate matter exposure in subway stations and the identification of heavy metal sources. Moreover, this study can be used as the fundamental data for the cell toxicity study of the subway-oriented heavy metal-containing particulate matter.

• Resources Recycling
• /
• v.33 no.1
• /
• pp.58-68
• /
• 2024

Critical minerals such as nickel, cobalt and lithium, are known as materials for cathodic active materials of lithium ion batteries. The consumption of the minerals is expected to grow with increasing the demands of electric vehicles, resulting from carbon neutrality. Especially, the demand for LIB (lithium ion battery) recycling is expected to increase to meet the supply of nickel, cobalt and lithium for LIB. The recycling of EOL (end-of-life) LIB can be achieved by leaching EOL LIB using inorganic acid such as HCl, HNO₃ and H₂SO₄, which are regarded as hazardous materials. In the present study, the potential use of MSA (Methanesulfonic acid), as an alternative lixiviant replacing sulfuric acid was investigated. In addition, leaching behaviors of NCM black mass leaching with MSA was also investigated by studying various leaching factors such as chemical concentration, leaching time, pulp density (P/D) and temperatures. The leaching efficiency of nickel (Ni), cobalt (Co), lithium (Li), and manganese (Mn) from LIB was enhanced by increasing concentration of lixiviant and reductant, leaching time and temperature. The maximum leaching of the metals was above 99% at 80℃. In addition, MSA can replace sulfuric acid to recover Ni, Co, Li, Mn from NCM black mass.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.1010-1017
• /
• 2011

The use of plated front contact for metallization of silicon solar cell may alternative technologies as a screen printed and silver paste contact. This technologies should allow the formation of contact with low contact resistivity a high line conductivity and also reduction of shading losses. A selective emitter structure with highly dopes regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing. When fabricated Ni/Cu plating metallization cell with a selective emitter structure, it has been shown that efficiencies of up to 18% have been achieved using this technology.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.113-119
• /
• 2013

The transient liquid phase (TLP) bonding was used to fabricate autogenous joints in a magnesium alloy AZ31 with the aid of a pure Ni interlayer. A $13{\mu}m$ thick pure Ni foil was used in order to form a Mg-Ni eutectic liquid at the joint interface. The interface of reaction and composition profiles were investigated as a function of bonding time using a pressure of 0.16 MPa and a bonding temperature of $515^{\circ}C$. The quality of the joints produced was examined by metallurgical characterization and the joint microstructure developed across the diffusion bonds was related to changes in mechanical properties as a function of the bonding time.

• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.156-161
• /
• 1998

We have measured changes of the non-stoichiometry, $\Delta\delta$, in Fe-doped nicked oxide , by thermogravimetry for four iron fractions, x=0.01, 0.031, 0.057 and 0.10, and three temperatures, T=1273, 1373 and 1473 K. The obtained data can be modelled by a defect structure in which substitutional trivalent iron ions, FeNi, are compensated by cation vacancies, $V_{Ni}$", and (4:1)-clusters. These clusters consist of tetravalent interstitial iron, $Fe_i\;^4$

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.12
• /
• pp.83-89
• /
• 1996

The electrochemical spike oscillations at the nickel (Ni) electrode/(0.05M KHC$_{8}$H$_{4}$O$_{4}$) buffer solution (pH 9) interface have been studied using voltammetric and chronoamperometric methods. The nature of the periodic cathodic current spikes is the activation controlled currents due to the hydrogen evolution reaction and depends onthe fractioanl surface coverage of the adsorbed hydrogen intermediate or the cathodic potential. There is two kinds of the waveforms corresponding to two kinds of the cathodic current spike oscillations. The widths, periods, and amplitudes of the cathodic current spikes are 4 ms or 5ms, 151 ms or 302 ms, and < 30 mA or < 275 mA, respectively. The fast discharge and recombination reaction steps are 1.5 times and twice and faster than the slow discharge and recombination reaction steps. The fast and slow discharge and recombination reaction steps are 1.5 times and twice faster than the slow discharge and recombination reaction steps. The fast and slow discharge and recombination reactions corresponding to the fast and slow adsorption sites at the Ni cathode.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.88-93
• /
• 2007

Nano-sized Sn particles were coated with Ni-P layer using an electroless deposition method and their anodic performance was tested for lithium secondary batteries. Uniform coating layers were obtained, of which the thickness was controlled by varying the $Ni^{2+}$ concentration in the plating bath. It was found that the Ni-P layer plays two important roles in improving the anodic performance of Sn powder electrode. First, it prevents the inter-particle aggregation between Sn particles during the charge/discharge process. Second, it provides an electrical conduction pathway to the Sn particles, which allows an electrode fabrication without an addition of conductive carbon. A pseudo-optimized sample showed a good cyclability and high capacity ($>400mAh\;g^{-1}$) even without conductive carbon loading.

• Journal of Korea Foundry Society
• /
• v.8 no.4
• /
• pp.459-466
• /
• 1988

This study was carried out in the austempering temperature and time after Ni, Mo addition in purpose of modification of impact toughness of austempered ductile irons. Addition of alloy element and austempering treatment of $900^{\circ}C$ 60 minutes followed by $300^{\circ}C$, $350^{\circ}C$ and $400^{\circ}C$ for 60 minutes, in this case impact value was increased by ideal mixed structure. But impact value was decreased when holing time is 120minutes, this is attributed to segregation and carbide precipitation from high carbon austenite. Highest impact value was obtained by $350^{\circ}C$ (Mo-addition) and $400^{\circ}C$ (Ni-addition). This phenomena was caused by presence of remained austenite. At all austempering temperature,, Ni-added specimen showed higher impact values than that of Mo-added specimen. And hardness property was affected by austempering temperature and holding time rather than amounts of alloying element.