• Journal of Technologic Dentistry
• /
• v.34 no.4
• /
• pp.361-368
• /
• 2012

Purpose: The aim of this study was to analysis the composition on the centrifugal casting and the oxide on the casting temperature. Methods: The nickel based alloy were used in this study. Wax pattern specimens (10*10*2) were invested with phosphate-bonded investment in metal rings, the liquid/powder ratio and overall burn-out schedules for these investments were followed in accordance with the manufacturer's instructions. After casting, the alloy specimens were evaluated as regards composition(EPMA). The casting temperatures were as follows: $1400^{\circ}C$ and $1700^{\circ}C$. The quantitative analysis of oxides were scanning electron microscope(SEM), energy dispersive spectroscopy(EDS) and line scanning. Results: Nearer the injection lines showed that there is a large amount of nickel. Quantitative of oxides of Ni-Cr alloy cast from $1400^{\circ}C$ is lager than Ni-Cr alloy cast from $1700^{\circ}C$. Conclusion: Casting when using a centrifugal casting machine centrifugal force affects the composition of the alloy. The higher the temperature, the amount of oxide that is generated many.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.614-622
• /
• 1996

Efficient removal of nickel from the ferric chloride etching solution has been studied. At first, $Fe^{3+}$ was reduced to $Fe^{2+}$ by the electrolytic iron flake or the waste shadow mask iron plate. And then, $Ni^{2+}$ was removed from the solution by electrolytic iron powder. Under the optimum conditions the reduced rates of nickel were 99 % and 98%, respectively at the initial $Ni^{2+}$ concentrations of 1.0% and 0.1%. Sludge formed during reduction of $Fe^{3+}$ in the solution were analyzed by XRD and SEM.

• 연구논문집
• /
• s.28
• /
• pp.183-192
• /
• 1998

The wear and oxidation resistance of two phase nickel aluminides was investigated. Wear tests of various heat-treated specimens at room temperature and at $500^{\circ}C$ were performed under no lubricant condition in air by using a ball-on-disk type tribotester. Isothermal oxidation tests were made at $1100^{\circ}C$ in air flowing at the rate of 70cc/min and at $1000^{\circ}C$ in air by using TGA. Experimental results from wear tests showed that nickel aluminide with a higher content of Al had an improved wear resistance at both temperatures. Also the examination of the wear tracks after wear test at both room temperature and $500^{\circ}C$ indicated that regardless of the alloy compositions the wear tracks of the two phase nickel aluminides showed an abrasive type wear The improved oxidation resistance observed in the Ni-34at%Al alloy could to be attributed to the microstructural difference between the aluminides. An accelerated oxidation along the thin layer of $Ni_3AL$ along the grain boundary observed in the microstructure of the Ni-32at%Al aluminide could be attributed to the poor oxidation resistance.

• Journal of Surface Science and Engineering
• /
• v.50 no.6
• /
• pp.486-491
• /
• 2017

Silver nanowire (AgNW) transparent electrode is one of next generations of flexible and transparent electrode. The electrode shows high conductivity and high transparency comparable to ITO. However, the electrode is weak against heat. The wires are separated into nanodots at temperature above $200^{\circ}C$. It causes the electrical resistance increase. Moreover, it is vulnerable to oxygen and moisture in the atmosphere. The improvement of thermal and moisture resistance of silver nanowire transparent electrode is the most important for commercializing. We proposed silver nanowires transparent electrode which is capped with very thin nickel oxide layer. The nickel oxide layer is five nanometers of thickness, but the heat and moisture resistance of the transparent electrode is effectively improved. The AgNW/NiO electrode can endure at $300^{\circ}C$ of temperature for 30 minutes, and resistance is not increased for 180 hours at $85^{\circ}C$ of temperature and 85% of relative humidity. We showed an applications of transparent and flexible heater using the electrode, the heater is operated more than $180^{\circ}C$ of temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.10-11
• /
• 2006

In this study, the Ni/Co/TiN (6/2/25 nm) structure was deposited for thermal stability estimation. Vacuum (30 mTorrs) annealing was carried out to compare with furnace annealing in nitrogen ambient. The proposed Ni/Co/TiN structure exhibited low temperature silicidation and wide range of rapid thermal process (RTP) windows. The sheet resistance was too high to measure after furnace annealing at $600^{\circ}C$ due to the thin thickness (15 nm) of the nickel silicide. However, the sheet resistance maintained stable characteristics up to $600^{\circ}C$ for 30 min after vacuum annealing. Therefore, the low resistance of thin film nickel silicide was obtained by vacuum annealing at $600^{\circ}C$.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.272-278
• /
• 2021

In this study, high nickel layered LiNi_0.8Co_0.1Mn_0.1O₂ cathode materials for lithium-ion batteries were modified by yttrium doping and poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) coating. The effects of yttrium doping and PEDOT:PSS coating on the structural and electrochemical properties of the LiNi_0.8Co_0.1Mn_0.1O₂ cathode material were investigated and compared. The substitution of nickel with an electrochemically inert yttrium was confirmed to be successful in stabilizing the layered structure framework. Moreover, coating the surfaces of the LiNi_0.8Co_0.1Mn_0.1O₂ particles with a conductive polymer, PEDOT:PSS, improved the capacity retention, thermal stability, and impedance of the cathode material by increasing its ionic and electric conductivities.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.204-204
• /
• 2011

최근 자동차수명의 연장, 고품질, 내식내마모성 향상의 요구에 따라 아연도금 및 합금도금의 친환경화, 아연합금도금특성 향상, 흑색화 실현, 아연-철, 아연-니켈 벤딩성 향상, 주석-아연 합금도금과 무전해 Ni-W-P, Ni-B-W, 전해 NiSiC-PTFE, Ni-Diamond복합도금 등의 도금현장 적용과 도금 후 3가 크로메이트 도장 밀착성에 대한 품질기술지원이 요구되고 있다.

• Journal of the Korean Chemical Society
• /
• v.36 no.4
• /
• pp.540-545
• /
• 1992

Kinetics and mechanism on the solvent extraction of nickel(Ⅱ) with 8-hydroxyquinoline (HOx) was studied spectrophotometrically. Absorbance variation was measured by changing the 8-hydroxyquinoline concentration in the chloroform organic phase and the pH values in the aquous phase. By analyzing absorbance data the reaction rate was found to be the first order for 8-hydroxyquinoline concentration and the inverse first one for [H$^+$]. Therefore the rate determining step of the extraction reaction is the formation of the one-to-one metal chelate NiOx$^+$ and the rate equation is as follows; -d[Ni$^{2+}$]/dt = k[Ni$^{2+}$][Ox$^-$] = k'[Ni$^{2+}$][HOx]$_0$/[H$^+$]. The value of k' was evaluated from the slope of plot of log [Ni$^{2+}$]$_0$/[Ni$^{2+}$]$_t$ versus time and the rate constant k was calculated according to the equation k' = k ${\times}$ K$_{HOx}$ / K$_{D,HOx}$. From the temperature dependence of the extraction rate, the activation energy E$_a$ = 6.26 kcal/mol is calculated, and activation parameters, ${\Delta}$G$^{\neq}_{298}$ = 6.59 kcal/mol, ${\Delta}$H$^{\neq}_{298}$ = 5.68 kcal/mol, ${\Delta}$S$^{\neq}_{298}$ = -3.09 eu/mol are estimated.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.631-635
• /
• 2012

Nickel oxide was doped with a wide range of concentrations (mol%) of Aluminum (Al) by solvothermal synthesis; single-phased nano powder of nickel oxide was generated after calcination at$900^{\circ}C$. When the concentration of Al dopant was increased, the reduced intensity was confirmed through XRD analysis. Lattice parameters of the synthesized NiO powder were decreased after treatment of the dopant; parameters were increased when the concentration of Al was over the doping limit (5 mol% Al). The binding energy of $Ni^{2+}$ was chemically shifted to $Ni^{3+}$ by doping $Al^{3+}$ ion, as confirmed by the XPS analysis. The tilted structure of the synthesized NiO with 5 mol% Al dopant and the polycrystalline structure of the $Ni_{0.75}Al_{0.25}O$ were observed by HR-TEM analysis. The electrical conductivity of the newly synthesized NiO was highly improved by Al doping in the conductivity test. The electrical conductivity values of the commercial NiO and the synthesized NiO with 5 mol% Al dopant ($Ni_{0.95}Al_{0.05}O$) were 1,400 s/cm and 2,230 s/cm at $750^{\circ}C$, respectively. However, the electrical conductivity of the synthesized NiO with 10 mol% Al dopant ($Ni_{0.9}Al_{0.1}O$) decreased due to the scattering of free-electrons caused by the large number of impurity atoms; the electrical conductivity of $Ni_{0.9}Al_{0.1}O$ was 545 s/cm at $750^{\circ}C$.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.341-342
• /
• 2008