• 한국환경보건학회지
• /
• 제27권4호
• /
• pp.63-71
• /
• 2001

PM 2.5/ samples were measured at two sites, Hadan(suburban site) and Anrak (roadside site) in Busan area. PM 2.5/ sampling was performed for 24-hour intervals by the FH9.5 particulate sampler. Aerosol samples were collected on PTFE filter. A total of 60 particulate samples were collected, dad samples were measured for Particulate mass concentration, metallic elements (Cr, Mn, Ni. Cu. Se, Fe, Pb, and Zn) and waer-soluble elements (C $l^{[-10]}$ , N $O_{3}$$^{[-10]}$ ,S $O_{4}$$^{2-}$, N $H_{4}$$^{+}$, $Ca_{2}$$^{+}$, $Mg_{2}$$^{+}$ and $^{+}$.Mass concentration in Hadan ranged 24.23~57.12 $\mu\textrm{g}$/㎥ and 60.22~72.12 $\mu\textrm{g}$/㎥m Yellow Sand Events. Major cations in Hadan and Anrak site is N $H_{4}$$^{+}$and N $a^{+}$ respectively. SO42$^{[-10]}$ was the abundant specie in the PM 2.5 fraction for Hadan site an dAnrak site. Hadan site showed igher concentration in S $O_{4}$$^{2.1}$ and N $H_{4}$ $^{+}$ In Anrak site the concentration of S $O_{4}$/sip 2-/and N $a^{+}$ was higher than other ions Prominent metallic elements were Fe and Pb in two sites. Principal component analysis showed that main source of PM 2.5 aerosol particles was non-metal related source which was resulted in relating elements as Cr, Ni, and Pb at Hadan site, Anrak site also has resulted PM2.5 aerosol paricles source, which was related its element like Zn, and Ni,. The SAS package analysis also showed that long-range transport effect at Hadan area due to Yellow Sand Event by the prevailing weaterlies.ling weaterlies.

• 마이크로전자및패키징학회지
• /
• 제27권4호
• /
• pp.25-37
• /
• 2020

본 연구에서는 그래핀 소재의 전기전도성 및 자기적 특성을 향상시키기 위해 산화그래핀 표면상의 산소를 포함한 기능기와 열처리 환원공정을 이용하여 환원그래핀과 금속소재를 하리브리드화 하였다. 산화 그래핀 표면의 -OH, -COOH 등의 산소 포함 기능기들을 열처리 환원시킴과 동시에 금속이온을 기능기와의 이온교환법에 의해 치환 합성하는 연구를 진행하였다. 하이브리드 소재 합성에 사용된 금속은 Fe, Ag, Ni, Zn, Fe/Ag이며 SEM, TEM 및 EDS를 통해 환원 그래핀 표면 위에 균일한 크기의 금속 입자가 비교적 구형 잘 분산되었음을 확인하였다. 그래핀 표면상의 금속입자들은 모두 산화물 형태의 구조를 가지고 있었다. 하이브리드 소재의 전기적 특성을 확인하기 위해 rGO-metal hybrid 시료를 PET film에 dip-coating 방법으로 후막 필름을 형성시킨 후 면저항을 측정하였고, SEM을 통해 시편의 두께를 측정하여 비저항을 계산한 결과, 비저항의 범위는 2.14×10-5 ~ 3.5×10-3 ohm/cm범위에 있음을 확인하였다.

• 한국대기환경학회지
• /
• 제28권1호
• /
• pp.39-51
• /
• 2012

Aerosol slurry samples were collected in 60-min interval using Korean Semi-continuous Elements in Aerosol Sampler (KSEAS) between May 19 and June 6, 2010 at an urban site of Gwangju. The $PM_{2.5}$ samples were collected with a flow rate of 16.7 L/min and particles are grown by condensation of water vapor in a condenser maintained at ${\sim}5^{\circ}C$ after saturation by direct injection of steam. The resulting droplets are collected in a liquid slurry with a airdroplet separator. Concentrations of 16 elements (Al, Fe, Mn, Ca, K, Cu, Zn, Pb, Cd, Cr, Ti, V, Ni, Co, As, Se) in the collected slurry samples were determined off-line by ICP-MS. KSEAS sample analysis encompassed the sampling periods for which 24-hr average elemental species concentrations were calculated for comparison with those derived from 24-hr integrated filter samples. Relationship between elemental species measured by two methods indicated high correlation coefficients (r), mostly greater than r of 0.80. However, we note that concentrations of Al, K, Ca, Mn, and Fe, which are often associated with crustal elemental particles, in the KSEAS samples, were substantially lower (1.4~11 times) than those found in the typical filter-based samples. This discrepancy is probably due to difficulties in transferring insoluble dust particles to the collection vials in the KSEAS. Temporal profiles of elemental concentrations indicate that some transient events in their concentrations are observed over the sampling periods. For the elemental species studied, atmospheric concentrations during the transient events increased by factors of 4 in Mn~80 in Zn, compared to their background levels. Principle component analyses were applied to the hourly KSEAS data sets to identify sources affecting the concentrations of the metal constituents observed. In this study, we conclude that hourly measurements for particle-bound elemental constituents were extremely useful for revealing the short-term variability in their concentrations and developing insights into their sources.

• 한국세라믹학회지
• /
• 제55권1호
• /
• pp.50-54
• /
• 2018

This study investigated the long-term durability of catalyst(Pd or Fe)-infiltrated solid oxide cells for $CO_2$/steam co-electrolysis. Fuel-electrode supported solid oxide cells with dimensions of $5{\times}5cm^2$ were fabricated, and palladium or iron was subsequently introduced via wet infiltration (as a form of PdO or FeO solution). The metallic catalysts were employed in the fuel-electrode to promote $CO_2$ reduction via reverse water gas shift reactions. The metal-precursor particles were well-dispersed on the fuel-electrode substrate, which formed a bimetallic alloy with Ni embedded on the substrate during high-temperature reduction processes. These planar cells were tested using a mixture of $H_2O$ and $CO_2$ to measure the electrochemical and gas-production stabilities during 350 h of co-electrolysis operations. The results confirmed that compared to the Fe-infiltrated cell, the Pd-infiltrated cell had higher stabilities for both electrochemical reactions and gas-production given its resistance to carbon deposition.

• 한국산업보건학회지
• /
• 제26권2호
• /
• pp.225-236
• /
• 2016

Objectives: Nanomaterials have been used in various fields. As use of nanoproducts is increasing, workers dealing with nanomaterials are also gradually increasing. Exposure assessments for nanomaterials have been carried out for protection of worker's health in workplace. Exposure studies were mainly focused on manufacturing processes, but these studies on after-treatment processes such as refinement, weighing, and packing were insufficient. So, we investigated exposure characteristics of particles during after-treatment processes of $Al_2O_3$ fibers and Ni powders. Methods: Mass-production of Ni powder process was carried out in enclosed capture-type canopy hood. In a developing stage, $Al_2O_3$ was handled with a local ventilation unit. Exposure characteristics of particles were investigated for $Al_2O_3$ fiber and Ni powder processes during the periods of 10:00 to 16:00, 20 May 2014 and 13:00 to 16:00, 21 May 2014, respectively. Three real-time aerosol instruments were utilized in exposure assessment. A scanning mobility particle sizer(SMPS, nanoscan, model 3910, TSI) and an optical particle counter(OPC, portable aerosol spectrometer, model 1.109, Grimm) were used to determine the particle size distribution in the size range of 10-420 nm and $0.25-32{\mu}m$, respectively. In addition, a nanoparticle aerosol monitor(NAM, model 9000, TSI) was used to measure lung-deposited nanoparticle surface area. Membrane filters(isopore membrane filter, pore size of 100 nm) were also used for air sampling for the FE-SEM(model S-5000H, Hitachi) analysis using a personal sampling pump(model GilAir Plus by 2.5 L/min, Gilian). Conclusions: For Ni powder after-treatment process, only 27% increase in particle concentration was found during the process. However, for $Al_2O_3$ fiber after-treatment process, significant exposure(1.56-3.34 times) was observed during the process.

• 한국재료학회지
• /
• 제12권8호
• /
• pp.600-607
• /
• 2002

The Ni-Zn synthetic ferrite were acquired from thermally decomposing the metal nitrates Fe(NO$_3$)$_3$.$9H_2$O, Zn($NO_3$)$_2$.$6H_2$O, Ni($NO_3$)$_2$. $6H_2$O, and Cu($NO_3$)$_2$. $3H_2$O at $150^{\circ}C$ for 24 hours and was calcined at $500^{\circ}C$. Each of those was pulverized for 3, 6, 9, and 12 hours in a steel ball mill and was sintered between $700^{\circ}C$ and $1,000^{\circ}C$ for 1 hour, and then their microstructures and electromagnetic properties were examined. We could make the initial specimens chemically bonded in liquid at the temperature as low as $150^{\circ}C$, by using the melting points less than $200^{\circ}C$ of the metal nitrates instead of the mechanical ball milling, then narrowed a distance between the particles into a molecular level, and thus lowed sintering temperature by at least $200^{\circ}C$ to$ 300^{\circ}C$. Their initial permeability was 50 to 400 and their saturation magnetic induction density and coercive force 2,400 G and 0.3 Oe to 0.5 Oe each, which were similar to those of Ni- Zn ferrite synthesized in the conventional process. In the graph of initial permeability vs frequencies, we could observe a $180^{\circ}C$rotation of the magnetic domain, which appears in a broad band of microwave near the resonance frequency.

• Journal of Magnetics
• /
• 제7권2호
• /
• pp.29-39
• /
• 2002

The initial NiCuZn synthetic ferrite were acquired from thermally decomposing the metal nitrates $Fe(NO_3)_39H_2O, Zn(NO_3)_26H_2O, Ni(NO_3)_26H_2O, and Cu(NO_3)_23H_2O$ at $150^circ{C}$ for 24 hours, and then we calcined the synthetic powder at $500^circ{C}$, pulverized each of those for 3, 6, 9, 12, and 15 hours in a steel ball mill, sintered each at $700^circ{C}$ to $1,000^circ{C}$ for 1 hour, and thus studied their microstructures and electromagnetic properties. We could make the initial specimens chemically bonded in liquidity at a low-temperature $150^circ{C}$, by using the low melting points less than $200^circ{C}$ of the metal nitrates instead of the mechanical ball-mill pulverization, then narrow a distance between the particles into a molecular one, and thus lower the reaction point of sintering by at least $200^circ{C}$ to $300^circ{C}$. Their initial permeability was 50 to 400 and their maximum magnetic induction density and coercive force, 2,400 G and 0.3 Oe to 0.5 Oe respectively, which was similar to those of NiZnCu ferrite synthesized in the conventional process. In the graph of initial permeability by frequencies, a $180^circ{C}$ rotation of the magnetic domains which appears in a broad band of micro-wave before and after the resonance frequency, could be perceived.

• 한국대기환경학회지
• /
• 제20권4호
• /
• pp.555-569
• /
• 2004

Size -segregated measurements of aerosol composition using 8-stage DRUM impactor are used to determine the transport of natural and anthropogenic aerosols at Gosan site from 29 March to 30 May in 2002. Separation of ambient aerosols by DRUM impactor offers many Advantages over other standard filtration techniques. Some of the most important advantages are the ability to segregate into details by particle tire, to better preserve chemical integrity since the air stream doesn＇t pars through the deposit, to collect samples as a function of time, and to have a wide variety of impaction surfaces available to match analytical needs. Although the transport of Yellow sand is a well-known phenomenon in springtime, the result of measurement shows that not only soil dust but also anthropogenic aerosols, including sulfur, enriched trace metals such as Pb, Ni, Zn. Cu, Cr, As, Se, Br, are transported to Gosan in springtime. This study combines the size- and time-resolved aerosol composition measurements with isentropic, backward air-mass trajectories in order to identify some potential source regions of anthropogenic aerosols. As a result, during the NYS period, the average concentration of PM$_{10}$ was 46$\mu\textrm{g}$/㎥, Si, Al. S, Fe, Cl, K, Ca were higher than 1,000 ng/㎥ and Ti was about 100 ng/㎥. The concentrations of Zn, Mn, Cu. Pb, Br, Rb, V, Cr, Ni. At, Se ranged between 1 and 70 ng/㎥. More than 50% typical soil elements, tuck as Al, Si, Fe, Cd. Ti, Cr, Cu, Br. were distributed in a coarse particle range(5.0-12${\mu}{\textrm}{m}$). In other hand, anthropogenic pollutants, luck as S, N, Vi, were mainly distributed in a fine particle range (0.09-0.56${\mu}{\textrm}{m}$). During the YS period, PM$_{10}$ increased about 8 times than NYS period, and main soil elements, such as Al, Si, S, K, V, Mn, Fe also doubled in coarse particle range (1.15-12${\mu}{\textrm}{m}$). But Zn, As, Pb, Cu and Se, which distributed in the time aerosols (0.09-0.56${\mu}{\textrm}{m}$), were on the same level with or decreased than NYS period. Finally. except the YS Period, coarse particles (2.5-12${\mu}{\textrm}{m}$) are inferred to be influenced by soil, coal combustion, waste incineration, ferrous and nonferrous sources through similar pathways with Yellow Sand. But fine particles have different sources, such as coal combustion, gasoline vehicle, biomass burning, oil or coal combustion, nonferrous and ferrous metal sources, which are transported from China, Korea peninsula and local sources.ces.

• 한국분말재료학회지
• /
• 제9권6호
• /
• pp.394-408
• /
• 2002

Nanostructured high strength metastable Al-, Mg- and Ti-based alloys containing different amorphous, quasicrystalline and nanocrystalline phases are synthesized by non-equilibrium processing techniques. Such alloys can be prepared by quenching from the melt or by powder metallurgy techniques. This paper focuses on one hand on mechanically alloyed and ball milled powders containing different volume fractions of amorphous or nano-(quasi)crystalline phases, consolidated bulk specimens and, on the other hand. on cast specimens containing different constituent phases with different length-scale. As one example. $Mg_{55}Y_{15}Cu_{30}$- based metallic glass matrix composites are produced by mechanical alloying of elemental powder mixtures containing up to 30 vol.% $Y_2O_3$ particles. The comparison with the particle-free metallic glass reveals that the nanosized second phase oxide particles do not significantly affect the glass-forming ability upon mechanical alloying despite some limited particle dissolution. A supercooled liquid region with an extension of about 50 K can be maintained in the presence of the oxides. The distinct viscosity decrease in the supercooled liquid regime allows to consolidate the powders into bulk samples by uniaxial hot pressing. The $Y_2O_3$ additions increase the mechanical strength of the composites compared to the $Mg_{55}Y_{15}Cu_{30}$ metallic glass. The second example deals with Al-Mn-Ce and Al-Cu-Fe composites with quasicrystalline particles as reinforcements, which are prepared by quenching from the melt and by powder metallurgy. $Al_{98-x}Mn_xCe_2$ (x =5,6,7) melt-spun ribbons containing a major quasicrystalline phase coexisting with an Al-matrix on a nanometer scale are pulverized by ball milling. The powders are consolidated by hot extrusion. Grain growth during consolidation causes the formation of a micrometer-scale microstructure. Mechanical alloying of $Al_{63}Cu_{25}Fe_{12}$ leads to single-phase quasicrystalline powders. which are blended with different volume fractions of pure Al-powder and hot extruded forming $Al_{100-x}$$(Al_{0.63}Cu_{0.25}Fe_{0.12})_x$ (x = 40,50,60,80) micrometer-scale composites. Compression test data reveal a high yield strength of ${\sigma}_y{\geq}$700 MPa and a ductility of ${\varepsilon}_{pl}{\geq}$5% for than the Al-Mn-Ce bulk samples. The strength level of the Al-Cu-Fe alloys is ${\sigma}_y{\leq}$550 MPa significantly lower. By the addition of different amounts of aluminum, the mechanical properties can be tuned to a wide range. Finally, a bulk metallic glass-forming Ti-Cu-Ni-Sn alloy with in situ formed composite microstructure prepared by both centrifugal and injection casting presents more than 6% plastic strain under compressive stress at room temperature. The in situ formed composite contains dendritic hcp Ti solid solution precipitates and a few $Ti_3Sn,\;{\beta}$-(Cu, Sn) grains dispersed in a glassy matrix. The composite micro- structure can avoid the development of the highly localized shear bands typical for the room temperature defor-mation of monolithic glasses. Instead, widely developed shear bands with evident protuberance are observed. resulting in significant yielding and homogeneous plastic deformation over the entire sample.

• 분석과학
• /
• 제31권6호
• /
• pp.247-258
• /
• 2018

본 연구는 대기오염 영향에 따라 주변의 오염도를 식물로 평가할 수 있는 여부를 고찰하기 위한 연구이다. 국내 자생하는 소나무의 1년생 솔잎가지를 대상 평가지표로 선택하였으며, 채취지점은 공단지역 주변의 공원 2곳, 상대적으로 오염원이 적다고 예상되는 도시지역 공원 2곳을 선정하였다. 대상 채취지점에서 소나무 10 그루 이상에서 지상 2 m 이상의 솔잎가지를 채취하였다. 채취한 솔잎가지 표면에 침착된 입자상 물질에 대한 분석항목은 입도분포, 전자현미경의 표면촬영, 먼지제거율, 납 등 중금속, 다환방향족탄화수소류(PAHs) 유기물질이었다. 초음파를 이용하여 탈착시킨 침착된 입자상 물질의 입도는 $0.4{\mu}m{\sim}200{\mu}m$ 범위로 나타났고, $10{\mu}m$ 이하의 입도는 20 % 수준이었다. 솔잎가지에 침착된 입자상 물질의 양은 평균 0.636 mg (0.450 mg~0.825 mg) 이었고, 강수장치에의한제거율은 평균 18.8 % (10.0 %~27.6 %)로 나타났다. 고주파전처리장치로 산전처리한 후 ICP/MS로 측정한 입자상 물질의 중금속 농도는 As 18.8~26.3 mg/kg, Be 0.08~0.13 mg/kg, Cd 0.06~0.08 mg/kg, Cr 4.91~17.8 mg/kg, Cu 5.26~405 mg/kg, Fe 1,930~2,670 mg/kg, Pb 3.03~28.1 mg/kg, Mn 26.9~42.8 mg/kg, Ni 2.66~10.4 mg/kg, Al 4,560~8,730 mg/kg, Ba 2,500~6,120 mg/kg, Rb 5.27~17.8 mg/kg, Sr 40.9~95.3 mg/kg, Zn 4,030~8,260 mg/kg 범위이었다. 침착된 입자상 물질의 세척액을 액-액 추출 정제한 후 GC/MS/MS로 분석한 PAHs의 농도는 ${\Sigma}PAH_{16}$은 1.179~12.396 mg/kg, ${\Sigma}PAH_7$은 0.147~0.741 mg/kg 범위이었다.