• 한국표면공학회지
• /
• 제47권6호
• /
• pp.293-296
• /
• 2014

Fe-Ni has been of great interest because it is known as one of low thermal expansion alloys as various application areas. This alloy was fabricated by electroforming process, and effect of heat treatment on thermal expansion and hardness was investigated. Nano-crystalline structure of 13.3 - 63.5 nm in size was observed in the as-deposited alloy. To investigate the effect of heat treatment on grain growth and mechanical/thermal properties, we conducted hardness and coefficient of thermal expansion (CTE). From this, we confirmed these properties were varied by heat treatment. In this nano-crystalline alloy, we could observe abnormal behavior in thermal expansion between $350-400^{\circ}C$. Additionally, an abrupt change in hardness has also been observed. However, once the grains grow up to micro-sized the mechanical and thermal properties mentioned above were stabilized similar to those of bulk alloys due to heat treatment.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.558-566
• /
• 2009

The alloying effect of a small amount of nickel on low alloy steel for application to flue gas desulfurization(FGD) systems was studied. The structural characteristics of the rust layer were investigated by scanning electron microscopy(SEM). The electrochemical properties were examined by means of potentiostatic polarization test, potentiodynamic polarization test, and electrochemical impedance spectroscopy(EIS) in a modified green death solution of 16.9 vol.% $H_2SO_4$+0.35 vol.% HCl at $60^{\circ}C$ and an acid rain solution of $6.25{\times}10^{-5}M\;H_2SO_4+5.5{\times}10^{-3}M\;NaCl$ at room temperature. It was found that as the amount of nickel increased, the corrosion rate increased in the modified green death solution, which seemed to result from micro-galvanic corrosion between NiS and alloy matrix. In acid rain solution, the corrosion rate decreased as the amount of nickel increased due to the repulsive force of $NiFe_2O_4$ rust against $Cl^-$ ions by electronegativity.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.769-774
• /
• 2002

금속 산화물 상태으 혼합분말을 수소 환원하여 $Al_2O_3$ 분말 표면에 20 nm 크기의 Fe-Ni 합금이 균일하게 분산된 복합분말을 합성하였다. 상압소결을 이용하여 제조한 $Al_2O_3$/Fe-Ni 나노복합재료는 전 소결 온도 범위에서 단지 $Al_2O_3$와 ${gamma}$-Fe-Ni 상만으로 구성되어 있었고, $1350^{\circ}C$ 이상의 소결 온도에서 98% 이상의 치밀화를 이루었다. 최대 파괴강도와 파괴인성은 각각 574 MPa과 3.9 MP$a{\cdot}m1/2$로서 동일한 소결 조건의 순수 $Al_2O_3$ 보다 약 20% 증가하였다. 나노복합재료는 강자성 거동을 보였으며 분산상의 평균 입자 크기가 감소함에 따라 증가된 보자력 값을 나타내었다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(2)
• /
• pp.723-728
• /
• 1995

Alloy 600 표면에 레이저 빔을 이용하여 Ni, Cr 흔합분말 및 순수 Cr 분말로 표면합금층을 만들었다. 표면 합금층은 모재와 정합계면를 이루고 있으며 레이저 표면용용 시편에서와 같이 크게 면선단 응고부와 셀룰라 응고부로 나눌 수 있고, 모재에는 레이저 처리과정에서 생긴 수십 $\mu\textrm{m}$ 두께의 열영향 부위가 존재하였다. 그리고 합금층 내부에는 레이저 표면 용용된 시편과 달리 구형의 커다란 기공(pores)이 존재하였다. 레이저 표면 합금층에서 합금원소의 조성 분포를 조사하기 위해 레이저 처리된 시편에 대해 WDX 분석을 하였고, 합금층 내부에 Ni, Cr, Fe 원소의 조성 분포는 매우 균일하였다.

• 대한의용생체공학회:의공학회지
• /
• 제6권1호
• /
• pp.37-46
• /
• 1985

Development of a dental Ni-Cr alloy system for porcelain veneering crown and bridge was studied in this research. The principles of alloy design were a) It should not contain toxic beryllium. b) It should have low melting Point. c) It should be easily ground and polished. d) It should possess an adequate strength to resist the deformational force In the mouth. e) It should be bondable Ivith porcelain by chemically. After investigating the effect of minor elements such as boron and rare earth metals on the mechanical properties of the Ni-Cr alloy system, the compromised ideal composition for dental use was determined. The composition was l9.6%, Cr, 5.6% Mo, 3.4% Si, 1, 0% Fe, 0.01% Ti, 0.5-1.0% B, 0.2-0.6% misch metal, balance Ni. To compare the performance of experimental alloy with commercially available alloys, the properties such as strength, melting point, and bond strength were measured. The results Ivere as follows: a) Boron increases the strength of the alloy but reduces the elongation. b) Misch metal increases the strength when the boron content is low, but does not increase the strength when boron content is high. And it reduces the elongation drastically, c) Mechanical strength of the experimental alloy was not superior to commercially available Be containing alloy, but handling performance such as castability, ease of granting and polishing, and cuttability were superior to the Be containing alloy.

• KEPCO Journal on Electric Power and Energy
• /
• 제1권1호
• /
• pp.109-113
• /
• 2015

초임계 이산화탄소 발전 시스템 구축을 위해서는 고온, 고압의 열악한 환경에 노출되는 터빈, 열 교환기, 압축기와 같은 핵심 부품들의 내식성 평가는 반드시 수행되어야 한다. 이를 위해 후보소재 3종 Ferritic-Martensitic Steel (T92), Austenitic Steel (SS316L), Ni-based Alloy (IN738LC)를 선정하여 고온의 유사 초임계 $CO_2$ 발전 환경에서의 내식성 평가를 진행하였다. $600^{\circ}C$, $700^{\circ}C$의 2개의 온도 구간에서 $CO_2$ 분위기를 조성하여 800 시간 동안 노출시킨 뒤, Weight Change, Surface Morphology, Cross Section, Composition을 분석하였다. Cr-rich Protective Layer를 형성하는 Ni-based Alloy와 Fe/Cr-rich oxide를 형성하는 Austenitic Steel은 우수한 부식 저항성을 보인 반면에 Ferritic-Martensitic Steel은 높은 Weight Change와 Fe-rich Non-Protective Oxide가 관찰되어 상대적으로 낮은 부식 저항성을 보였다.

• 대한금속재료학회지
• /
• 제47권12호
• /
• pp.787-796
• /
• 2009

The fracture toughness improvement of Ni-Mn-Ga-Fe ferromagnetic shape memory alloys containing ductile particles was explained by direct observation of microfracture processes using an in situ loading stage installed inside a scanning electron microscope (SEM) chamber. The Ni-Mn-Ga-Fe alloys contained a considerable amount of ductile particles in the grains after the homogenization treatment at $800{\sim}1100^{\circ}C$. ${\gamma}$ particles were coarsened and distributed homogeneously along {$\beta}$ grain boundaries as well as inside {$\beta}$ grains as the homogenization temperature increased. The in situ microfracture observation results indicated that ${\gamma}$ particles effectively acted as blocking sites of crack propagation, and provided stable crack growth that could be confirmed by the R-curve analysis. This increase in fracture resistance with increasing crack length improved overall fracture properties of the alloys containing ${\gamma}$ particles.

• 한국수소및신에너지학회논문집
• /
• 제9권2호
• /
• pp.65-75
• /
• 1998

실용적인 Fe-Ti계 수소저장합금전극을 제조하기위한 적절한 공정을 확립하기위하여 다섯가지의 서로다른 제조공정을 선택하여 조사하여 보았다. 전극제조를 위해 먼저 FeTi 합금을 플라즈마 아크 용해로에서 용해제조한 후 분쇄하여 분말을 만들고 이를 성형하였다. 성형전에 합금분말을 Ni무전해도금하여 본 결과 Fe-Ti 합금의 방전특성이 개선되었으며 열처리효과에 대하여도 검토하여 보았다. 성형전 합금분말을 열처리하는 경우 열처리 온도가 증가함에 따라 전극의 방전용량이 증가함을 확인하였으며 특히 성형후 $100^{\circ}C$의 온도에서 열처리하는 경우 가장 좋은 결과를 얻을 수 있었다. 이들 결과로 부터, Ni무전해도금과 열처리가 Fe-Ti 계 전극의 방전성능을 향상시키는데 결정적인 역할을 함을 알 수 있었다. 또한, 본 연구에서 제안된 공정에 따라서 Mn을 첨가하여 Fe-Ti-Mn 전극을 제조하고 그 성능을 조사하여 본 결과 대단히 바람직한 결과를 얻었다.

• 한국수소및신에너지학회논문집
• /
• 제4권2호
• /
• pp.29-40
• /
• 1993

Intensive studies on the electrochemical characteristics of TiFe type alloy electrodes have been carried out to clarify the mechanism of electrochemical hydrogen absorption and desorption. It was found that electrochemical activation of the TiFe type alloys is difficult and that charge efficiencies are very low even after a decade of activation cycles. However, by the pretreatment of the powders such as gas activation and/or Ni chemical plating, charge efficiencies fairly increased, especially for the $TiFe_{0.8}Ni_{0.2}$ alloy. It was considered that difficulties to activation and lower charge efficies of the alloys are due to the presence of the passivation films, which prohibit inward diffusion of hydrogen and promote the combination of adsorbed hydrogen atom to gas bubbles during the electrochemical charge. In addition, lower diffusivity of hydrogen in the alloys may be played an important role lowering the charge efficiencies.

• 열처리공학회지
• /
• 제11권2호
• /
• pp.75-81
• /
• 1998

The effect of thermomechanical treatment on thermal expantion and melting point of Fe-30%Ni-0.35%C alloy was investigated. The dimention changes of the ausformed martensite and the marformed martensite were decreased with increasing deformation degree in the range of $25{\sim}350^{\circ}C$ prior to reverse transformation but became larger in the range of $500{\sim}800^{\circ}C$ after the reverse transformation. The dimension change and the thermal expansion coefficient were reduced in the order of the deformed austenite, the marformed martensite and the ausformed martensite in the range of $25{\sim}800^{\circ}C$. Therefore, the ausforming treatment is more effective than the marforming treatment in improving the heat-resistance. The melting points of the deformed austenite, the ausformed martensite and the marformed martensite were lowered as either the heating rate or the degree of deformation was increased.