• 한국재료학회지
• /
• 제27권8호
• /
• pp.409-415
• /
• 2017

For enhanced cavitation erosion resistance of vessel propellers, an electroless Ni-P plating method was introduced to form a coating layer with high hardness on the surface of Cu alloy (CAC703C) used as vessel propeller material. An electroless Ni-P plating reaction generated by Fe atoms in the Cu alloy occurred, forming a uniform amorphous layer with P content of ~10 wt%. The amorphous layer transformed to (Ni3P+Ni) two phase structure after heat treatment. Cavitation erosion tests following the ASTM G-32 standard were carried out to relate the microstructural changes by heat treatment and the cavitation erosion resistance in distilled water and 3.5 wt% NaCl solutions. It was possible to obtain excellent cavitation erosion resistance through careful microstructural control of the coating layer, demonstrating that this electroless Ni-P plating process is a viable coating process for the enhancement of the cavitation erosion resistance of vessel propellers.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.857-863
• /
• 2017

본 논문은 다단연소사이클 엔진의 연소실 내벽을 고온, 고압의 환경으로부터 보호하기 위한 열차폐 코팅 공정 개발에 관한 내용이다. 기존 연소기 내벽에는 열차폐 특성이 우수한 Zr 기반의 세라믹용사코팅을 적용했지만, 세라믹의 특성상 연소실 내벽(금속)과 열팽창계수 차이로 인해 박리가 발생할 수 있다. 때문에 로켓 선진국에서는 열차폐 효과를 다소 희생 하더라도 밀착력 향상을 위하여 금속계 코팅인 Ni-Cr 도금을 적용하고 있다. 본 연구에서는 연소기에 적용 가능한 상향 순환식 유동셀을 적용한 도금조를 개발했으며, 반복적인 공정 개선을 통해 도금 두께 $100{\mu}m$이상, ${\pm}10%$의 두께 균일도를 만족하는 Ni, Cr 도금 공정조건을 확립했다.

• 한국추진공학회지
• /
• 제14권5호
• /
• pp.45-50
• /
• 2010

연료링의 위치 및 열차폐 코팅의 종류에 따른 연소기의 재생냉각 특성을 검토하였다. 연료링을 노즐의 중간 부분에 위치시키고 냉각채널을 분기시켜서 설계하는 방법이 열적으로 타당함을 확인하였다. 또한 복합재를 이용한 노즐확장부가 적용 가능한 기술적 상황이라면, 팽창비가 높고 열유속이 낮은 노즐 후류 부분은 이를 이용하는 것이 매우 적절하다고 판단된다. 적용 가능한 열차폐 코팅 중에서 30톤급 연소기 및 가스발생기 개발과정에서 사용했던 $Y_2O_3$ stabilized $ZrO_2$과 내산화성이 우수한 Ni/Cr을 고려하였다. 내산화성이 우수한 Ni/Cr에 비해 세라믹 코팅($Y_2O_3$ stabilized $ZrO_2$)이 열차폐 효과가 우수한 것으로 파악되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.145-149
• /
• 2010

연료링의 위치 및 열차폐 코팅의 종류에 따른 연소기의 재생냉각 특성을 검토하였다. 연료링을 노즐의 중간 부분에 위치시키고 냉각채널을 분기시켜서 설계하는 방법이 열적으로 타당함을 확인하였다. 또한 복합재를 이용한 노즐확장부가 적용 가능한 기술적 상황이라면, 팽창비가 높고 열유속이 낮은 노즐 후류 부분은 이를 이용하는 것이 매우 적절하다고 판단된다. 적용 가능한 열차폐 코팅 중에서 30톤급 연소기 및 가스발생기 개발과정에서 사용했던 $Y_2O_3$ stabilized $ZrO_2$과 내산화성이 우수한 Ni/Cr을 고려하였다. 내산화성이 우수한 Ni/Cr에 비해 세라믹 코팅($Y_2O_3$ stabilized $ZrO_2$)이 열차폐 효과가 우수한 것으로 파악되었다.

• 한국표면공학회지
• /
• 제42권4호
• /
• pp.157-160
• /
• 2009

Many fundamental studies have been carried out regarding waste water and hazardous gas treatments technologies using the photolysis effect of $TiO_2$. However, a permanent use of $TiO_2$ particles immobilized using organic or organic-inorganic binders is impossible. In this study, Ni-$TiO_2$ composite coating was produced by electroless plating to trap $TiO_2$ particles in the Ni coating layer. The electroless plating was performed in the bath solutions with three different concentrations of $TiO_2$ particles : 10 g/l, 20 g/l, and 40 g/l. The surface and photolytic characteristics of the coating layer was investigated by the use of SEM, a scratch tester, and an UV-Visible spectrophotometer. The results showed that the amounts of immobilized $TiO_2$ particles and the photolytic rate of the coating increased with the initial content of $TiO_2$ particles in the electroless bath. In addition, the photolytic rate of the Ni-$TiO_2$ composite coating was remarkably promoted by etching process in 10% HCl solution.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.171-177
• /
• 2021

This paper is concerned with the surface hardness measurement of NiP-coated AA7050 using different loads from 10 to 100 g. The surface hardness was observed to increase from 180 to 600 H_v with increasing NiP layer thickness, depending on the load applied for indentation. When NiP coating thickness is thinner than 2 ㎛, the surface hardness of NiP-coated AA7050 was mainly determined by AA7050 substrate, while it was significantly increased by NiP coating layer when NiP coating thickness is thicker than 2 ㎛. Hardness of AA7050 substrate itself was not dependent on the applied load but the hardness of NiP-coated AA7050 was largely influenced by the load applied for indentation. The largest difference of hardness between 10 g and 100g of applied loads, was obtained at the NiP thickness of about 8 ㎛ above which the measured hardness at 10 g reached a maximum value of about 600 H_v. It was also observed that indentation-induced plastic deformation next to the indented zone occurs when NiP layer is 5.64 times thicker than the depth of impression formed by indentation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.278-281
• /
• 2009

Selective laser sintering(SLS), a kind of rapid prototyping technology, can provide a process to form many types of coatings. Coated layers by selective laser melting are highly influenced by substrate, powder and laser parameters such as laser power, scan rate, fill spacing and layer thickness. Therefore an attempt to fabricate Fe-Ni-Cr coating on AISI H13 tool steel has been performed by selective laser sintering. In this study, Fe-Ni-Cr coating was produced by experimental facilities consisting of a 200W fiber laser which can be focused to 0.08mm and atmospheric chamber which can control atmospheric pressure with Ar. With power increase or energy density decrease, line width was decreased and line surface quality was improved with energy density increase. Surface quality of coating layer was improved with fill spacing optimization or layer thickness decrease.

• 열처리공학회지
• /
• 제19권2호
• /
• pp.103-108
• /
• 2006

Microstructural evolution of Pt-aluminide coated Ni-based superalloy has been investigated with ductilization heat treatment. The Pt coat was prepared on the superalloy and then aluminide coating was conducted using a pack cementation process. Samples were heat-treated at $1050^{\circ}C$ for 2 hrs and the microstructure and element analysis were preformed. A various precipitated compounds were observed within the coating layer and the diffusion region in the Pt-aluminide coating and heat treatment, indicating that the bi-phase compounds of $PtAl_2$ and NiAl were performed during the Pt-aluminide coating, whereas $M_{23}C_6$, MC, $Ni_3Al$ and ${\sigma}$ phases were precipitated in the inter-diffusion region. The bi-phase compounds of $PtAl_2$ and NiAl were transformed into the single phase compound of $PtAl_2$ with the heat treatment, increasing the amount of carbide and ${\sigma}$ phase.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.692-693
• /
• 2006

Behavior of stoichiometric and near-stoichiometric NiAl at plasma spray deposition, without and with a bond coat, for coating layers realization on a low alloyed steel substrate, has been investigated. In all variants, NiAl particle melting and subsequent welding at the impact with substrate were observed, forming a relatively compact and adherent coating layer with the NiAl stability maintaining - all assuring the coating layer oxidation and corrosion resistance. Good results from these points of view, also validated through corrosion tests, were obtained for 45:55 Ni:Al composition without a bond coat but adopting an Ar protective surrounding of plasma jet.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 추계학술대회 논문집
• /
• pp.275-276
• /
• 2015

기존의 상용화된 Ni-Cr tie-coating 물질은 내열성 시험 후 강도가 저하되고, Cr 성분이 patterning후에 완벽하게 제거 되지 않아서 누설 전류를 만드는 단점을 갖고 있다. 따라서 이 연구에서는 기존의 Ni-Cr 과 삼원계 Ni-Cr-X(X는 Nb, V, Mo, Ti) 물질의 패터닝성과 내열성을 비교하였다.