• 제목/요약/키워드: Ni-20 Cr

검색결과 319건 처리시간 0.024초

Inconel 600에 있어서 Al 및 Al-Cr擴酸浸透 被覆處理에 따른 被覆層의 特性과 耐蝕性 (Microstructure and Hot Corrosion Resistance of Aluminide and Chromium-Aluminide Coatings for Inconel 600)

  • 정린상;박경채;박수호
    • 한국표면공학회지
    • /
    • 제20권3호
    • /
    • pp.95-105
    • /
    • 1987
  • For the purpose of improving the hot corrosion resistance of Ni-base superalloy, Inconel 600, aluminide and chromium-aluminide coatings by pack cementation process were studied. The morphology of these coatings is dependent on the type of process employed. And their overall composition depends on the composition of the base alloy and on the nature of the cement. Therefore the different aluminide and chromium-aluminide coatings obtained on a superalloy do not possess the same resistance to oxidation and hot corrosion. The mechanisms governing the formation of the coatings and the composition of the coating were varied by pack composition and temperature, and cyclic hot corrosion resistance of the auluminide coating formed by one-step process was inferior to that of the coating formed by two-step process. and Cr-Al composite coating showed good resistance for cyclic hot corrosion.

  • PDF

고장력강의 부식피로균열전파에 미치는 하중파형의 영향과 양극용해기구의 역할 (Effect of Stress Waveform on Corrosion Fatigue Crack Propagation in High Strength Steels-the Role of Anodic Dissolution Mechanism)

  • 하회석;이성근
    • 한국해양공학회지
    • /
    • 제7권1호
    • /
    • pp.147-155
    • /
    • 1993
  • The effect of stress waveforms on corrosin fatigue and the role of dissolution mechanism in 3NilCr steel and 20Ni maraging steel have been investigated in aerated 3% NaCl solution and synthetic seawater under sinusoidal, triangular, square, positive sawtooth, negative sawtooth, and trapezoidal stress waveforms with open circuit at frequency of 1Hz and stress ratio of 0.1. The crack growth rates under square waveform were substantially lower than under sinusoidal and triangular waveforms, but the crack growth rates under sinusoidal waveform were slightly higher under triangular waveform. For a given frequency the growth rates under the positive sawtooth waveform are higher than those under the negative sawtooth waveform. The fatigue crack growth rates of most specimens were in good agreement with the values calculated by the model based on the dissoultion mechanism.

  • PDF

고크롬주철의 잔류오스테나이트함량에 미치는 화학조성 및 불안정화열처리의 영향 (The Effect of Chemical Composition and Destabilization Heat Treatment on the Amount of Retained Austenite in High Chromium Cast Irons)

  • 류성곤
    • 한국재료학회지
    • /
    • 제6권4호
    • /
    • pp.372-378
    • /
    • 1996
  • 고크롬주철에 있어서 기지 및 탄화물의 조직제어는 내마모성의 향상을 위해 필수적이다. 특히 기지조직내의 잔류오스테나이트함량은 최적 내마모성을 얻기위해 반드시 조절되어야 한다. 본 연구에서는 3% C-18%(or 25%)Cr-Mo-Ni-Mn 고크롬주철을 80$0^{\circ}C$, 90$0^{\circ}C$, 100$0^{\circ}C$ 및 110$0^{\circ}C$의 질소분위기 하에서 각각 20분 불안정화열처리를 행한 후 공냉시켰다. 잔류오스테나이트의 함량은 Xtjs 회절시험을 통해 측정하였으며 회절 peak는 $\alpha$200, $\alpha$220, ${\gamma}$220그리고 ${\gamma}$311을 이용하였다. 화학조성, 불안정화열처리의 온도 및 시간, 그리고 잔류오스테니이트함량강의 관계식을 도출하였다.

  • PDF

유기물원이 다른 퇴비연용이 밭토양의 화학성 변화에 미치는 영향 (The Effect of Long-term Application of Different Organic Material Sources on Chemical Properties of Upland Soil)

  • 김종구;이경보;이상복;이덕배;김성조
    • 한국토양비료학회지
    • /
    • 제32권3호
    • /
    • pp.239-253
    • /
    • 1999
  • 본 연구는 밭 토양에서 종류가 상이한 퇴비시용이 토양 중 이화학성 변동에 미치는 영향을 구명하기 위하여 수행하였다. 밭토양 토성은 양토와 사양토를 공시하여 계분퇴비, 우분퇴비, 분뇨잔사 및 식품오니퇴비 등 4종을 사용하였다. 퇴비 시용량은 0, 40, $80Mg\;ha^{-1}$ 수준으로 처리하여 1994년부터 1997년도까지 4년간 시험한 결과를 요약하면 다음과 같다. 밭 토양의 pH는 분뇨잔사 연용구에서 pH 4.4~5.0까지 감소되었으며, 다른 퇴비시용구는 무시용구에 비하며 증가되는 경향이었다. 밭 토양의 EC변화는 퇴비시용 후 20일경에 제일 높았다가 그후 40일까지 낮아진 후 일정한 수준을 유지하였다. 토양 중 가용성 질소함량은 퇴비 시용 초지에는 $NH_4-N$가, 후기에는 $NO_3-N$함량이 높은 비율로 용출 되었고, 퇴비종류별로는 분뇨잔사 시용구가 제일 높았다. 밭 토양의 유효인산은 양토에서는 토심 0~20cm 부위에, 사양토는 0~50cm 부위까지 집적되었다. 퇴비 연용에 의한 년간 누적량은 사양토가 양토보다 17%정도 더 많았다. 토양의 염기포화도는 퇴비 시용량이 많고 연용 회수가 많을수록 증가되었다. 양토의 무처리구 염기포화도는 45%인 반면에 퇴비 $80Mg\;ha^{-1}$을 4년간 연용한 처리구 87~97% 범위이었다. 사양토는 무처리구의 염기포화도가 30.4% 이었으나 퇴비 $80Mg\;ha^{-1}$을 3년간 연용한 처리구는 81~92%에 달하였다. 동일한 퇴비 시용 수준에서 연평균 염기포화도 증가율은 사양토가 양토보다 2.0~3.7배 더 높았다. 밭 토양 증 양이온은 퇴비 시용으로 무시용구에 비하여 Ca은 2배, K는 3~5배, Mg는 2~3배가 증가되었다. 토심별로는 0~20cm 부위에 가장 많이 포화되었으며, 토심이 깊어질수록 포화도는 낮아지는 경향이었다. 토양 중 중금속함량은 계분 및 우분퇴비 시용시는 무시용과 차이가 없었으나 분뇨잔사 시용으로 Ni, Fe, Cu, Zn 등이, 식품오니 시용구에서는 Ni, Cr 함량이 무시용보다 약간씩 증가되었다.

  • PDF

유기물원이 다른 퇴비연용이 밭토양의 화학성 변화에 미치는 영향 (The Effect of Long-term Application of Different Organic Material Sources on Chemical Properties of Upland Soil)

  • 김종구;이경보;이상복;이덕배;김성조
    • 한국토양비료학회지
    • /
    • 제33권6호
    • /
    • pp.416-431
    • /
    • 2000
  • 본 연구는 밭 토양에서 종류가 상이한 퇴비시용이 토양 중 이화학생 변동에 미치는 영향을 구명하기 위하여 수행하였다. 밭토양 토성은 양토와 사양토를 공시하여 계분퇴비, 우분퇴비, 분뇨잔사 및 식품오니퇴비 등 4종을 사용하였다. 퇴비 시용량은 0, 40, $80Mg\;ha^{-1}$ 수준으로 처리하여 1994년부터 1997년도까지 4년간 시험한 결과를 요약하면 다음과 같다. 발 토양의 pH는 분뇨잔사 연용구에서 pH 4.4~5.0까지 감소되었으며, 다른 퇴비시용구는 무시용구에 비하여 증가되는 경향이었다. 밭 토양의 EC변화는 퇴비시용 후 20일경에 제일 높았다가 그후 40일까지 낮아진 후 일정한 수준을 유지하였다. 토양 중 가용성 질소 함량은 퇴비 시용 초기에는 $NH_4-N$가, 후기에는 $NO_3-N$함량이 높은 비율로 용출 되었고, 퇴비종류별로는 분뇨잔사 시용구가 제일 높았다. 밭 토양의 유효인산은 양토에서는 토심 0~20cm 부위에, 사양토는 0~50cm 부위까지 집적되었다. 퇴비 연용에 의한 년간 누적량은 사양토가 양토보다 17%정도 더 많았다. 토양의 염기포화도는 퇴비 시용량이 많고 연용 회수가 많을수록 증가되었다. 양토의 무처리구 염기포화도는 45%인 반면에 퇴비 $80Mg\;ha^{-1}$을 4년간 연용한 처리구 87~97% 범위이었다. 사양토는 무처리구의 염기포화도가 30.4% 이었으나 퇴비 $80Mg\;ha^{-1}$을 3년간 연용한 처리구는 81~92%에 달하였다. 동일한 퇴비시용 수준에서 연평균 염기포화도 증가율은 사양토가 양토보다 2.0~3.7배 더 높았다. 밭 토양 중 양이온은 퇴비 시용으로 무시용구에 비하여 Ca은 2배, K는 3~5배, Mg는 2~3배가 증가되었다. 토심별로는 0~20cm 부위에 가장 많이 포화되었으며, 토심이 깊어질수록 포화도는 낮아지는 경향이었다. 토양 중 중금속함량은 계분 및 우분퇴비 시용시는 무시용과 차이가 없었으나, 분뇨잔사 시용으로 Ni, Fe, Cu, Zn등이, 식품오니 시용구에서는 Ni, Cr함량이 무시용보다 약간씩 증가되었다.

  • PDF

논 관개수중 영양물질의 함량변화와 천연공급량 (Changes of Nutrients Content and Natural Supplies by Irrigation Water during the Rice Cultivation)

  • 한강완;전재철;조재영;김성조
    • 한국환경농학회지
    • /
    • 제16권4호
    • /
    • pp.394-398
    • /
    • 1997
  • 전라북도 진안군 마령면 평지리 일대 1.0ha의 논을 대상으로 벼농사 재배기간중 공급되는 관개수중에 함유된 영양물질과 오염물질의 함량 및 총 관개유량 측정을 통하여 논에 부하되는 영양물질과 중금속의 유입량을 시기별로 조사한 결과는 다음과 같다. 관개용수의 pH는 6.45${\sim}$8.34의 범위였으며, 전기전도도는 관개초기에만 $110{\mu}S/cm$ 수준을 유지하였으며 그밖에는 $90{\mu}S/cm$ 수준을 유지하였다. 전질소, 암모니아태질소 및 질산태질소의 함량은 각각 3.09${\sim}$12.46, 0.17${\sim}$1.34, 2.70~10.72mg/L 수준이었으며, 전인산의 함량은 0.09~0.22mg/L, orthophosphate는 검출되지 않았다. $Ca^{++}$는 0.89~5.12, $Mg^{++}$는 1.12~2.76, $Na^{+}$는 1.74~4.52, $Ka^+$는 1.34~4.18mg/L의 범위였으며 시기별로 큰 차이를 나타내지 않았다. 또한 $Cl^-$$SO_4\;^{2-}$는 각각 1.3~24.9, 3.5~20.3mg/L의 범위로 이앙초기에 높았다가 점차적으로 낮아지는 경향이었다. 중금속오염물질중 Cu와 Zn만이 각각 0.001~0.009, 0.007~0.091mg/L로 나타났을 뿐 Pb, Cd, Cr, Ni는 검출되지 않았다. 벼재배기간동안 1.0ha의 논에 $4,250m^3$의 관개수를 공급하였을 때 영양물질의 천연공급량은 전질소 29.68kg/1.0ha, 암모니아태질소 1.80kg/1.0ha, 질산태질소 24.57kg/1.0ha, 전인산 0.51kg/1.0ha으로 나타났다. 대표적인 양이온으로 $Ca^{++},\;Mg^{++},\;Na^+,\;K^+$는 각각 9.42, 7.09, 13.34, 9.08kg/1.0ha의 수준으로 공급되었으며 $Na^{+}>\;Ca^{++}>\;K^{+}>\;Mg^{++}$의 순서였다. 음이온으로 $Cl^-$$SO_4\;^{2-}$는 각각 40.27, 41.38kg/1.0ha으로 나타났다. 조사대상 6가지 중금속중 Cu와 Zn만이 관개수를 통하여 각각 0.17kg/1.0ha, 0.133kg/1.0ha 정도 논토양에 부하되었을 뿐 Pb, Cd, Cr, Ni은 검출되지 않았다.

  • PDF

STS 316L 소결체의 대기중 고온산화 거동 (The Oxidation Behavior of Sintered STS 316L at High-Temperature in the Air)

  • 김혜성;이종필;박동규;안인섭
    • 한국분말재료학회지
    • /
    • 제20권6호
    • /
    • pp.432-438
    • /
    • 2013
  • In this study, analysis on the oxidation behavior was conducted by a series of high-temperature oxidation tests at both $800^{\circ}C$, $900^{\circ}C$ and 1000 in the air with sintered STS 316L. The weight gain of each oxidized specimen was measured, the oxidized surface morphologies and composition of oxidation layer were analyzed with Scanning Electron Microscope-Energy Dispersive x-ray Spectroscopy (SEM-EDS), finally, the phase change and composition of the oxidized specimen were shown by X-Ray Diffraction (XRD). As a result, the weight gain increased sharply at $1000^{\circ}C$ when oxidation test was conducted for 210 hours. Also, a plentiful of pores were observed in the surface oxidation layers at $900^{\circ}C$ for 210 hours. In addition, the following conclusions on oxidation behavior of sintered STS 316L can be obtained: $Cr_2O_3$ can be formed on pores by influxing oxygen through open-pores, $(Fe_{0.6}Cr_{0.4})_2O_3$ can be generated on the inner oxidation layer, and $Fe_2O_3$ was on the outer oxidation layer. Also, $NiFe_2O_4$ could be precipitated if the oxidation time was kept longer.

DRUM impactor를 이용한 대기 입자상 물질 중 원소성분의 입경분포 특성 : 제주도 고산지역의 2002년 봄철 (3.29-5.30) 측정 연구 (Size Distributions of Trace Elements in Airborn Particulates Collected using Drum impactor at Gosan, Jeju Island : Measurements in Springtime 2002)

  • 한진석;문광주;류성윤;안준영;공부주;홍유덕;김영준
    • 한국대기환경학회지
    • /
    • 제20권4호
    • /
    • pp.555-569
    • /
    • 2004
  • Size -segregated measurements of aerosol composition using 8-stage DRUM impactor are used to determine the transport of natural and anthropogenic aerosols at Gosan site from 29 March to 30 May in 2002. Separation of ambient aerosols by DRUM impactor offers many Advantages over other standard filtration techniques. Some of the most important advantages are the ability to segregate into details by particle tire, to better preserve chemical integrity since the air stream doesn't pars through the deposit, to collect samples as a function of time, and to have a wide variety of impaction surfaces available to match analytical needs. Although the transport of Yellow sand is a well-known phenomenon in springtime, the result of measurement shows that not only soil dust but also anthropogenic aerosols, including sulfur, enriched trace metals such as Pb, Ni, Zn. Cu, Cr, As, Se, Br, are transported to Gosan in springtime. This study combines the size- and time-resolved aerosol composition measurements with isentropic, backward air-mass trajectories in order to identify some potential source regions of anthropogenic aerosols. As a result, during the NYS period, the average concentration of PM$_{10}$ was 46$\mu\textrm{g}$/㎥, Si, Al. S, Fe, Cl, K, Ca were higher than 1,000 ng/㎥ and Ti was about 100 ng/㎥. The concentrations of Zn, Mn, Cu. Pb, Br, Rb, V, Cr, Ni. At, Se ranged between 1 and 70 ng/㎥. More than 50% typical soil elements, tuck as Al, Si, Fe, Cd. Ti, Cr, Cu, Br. were distributed in a coarse particle range(5.0-12${\mu}{\textrm}{m}$). In other hand, anthropogenic pollutants, luck as S, N, Vi, were mainly distributed in a fine particle range (0.09-0.56${\mu}{\textrm}{m}$). During the YS period, PM$_{10}$ increased about 8 times than NYS period, and main soil elements, such as Al, Si, S, K, V, Mn, Fe also doubled in coarse particle range (1.15-12${\mu}{\textrm}{m}$). But Zn, As, Pb, Cu and Se, which distributed in the time aerosols (0.09-0.56${\mu}{\textrm}{m}$), were on the same level with or decreased than NYS period. Finally. except the YS Period, coarse particles (2.5-12${\mu}{\textrm}{m}$) are inferred to be influenced by soil, coal combustion, waste incineration, ferrous and nonferrous sources through similar pathways with Yellow Sand. But fine particles have different sources, such as coal combustion, gasoline vehicle, biomass burning, oil or coal combustion, nonferrous and ferrous metal sources, which are transported from China, Korea peninsula and local sources.ces.

황해 폐기물 투기해역(서해병) 표층 퇴적물의 금속원소 분포 (Concentration of metallic elements in surface sediments at a waste disposal site in the Yellow Sea)

  • 고혁준;최영찬;박성은;차형기;장대수;이충일;윤한삼
    • 한국환경과학회지
    • /
    • 제22권7호
    • /
    • pp.787-799
    • /
    • 2013
  • The aim of this study was to investigate the accumulation of metallic elements and the control effect of marine pollution caused by ocean dumping in the sediments at a waste disposal area in the Yellow Sea. In July 2009, concentrations of organic matter and metallic elements (Al, Fe, As, Cd, Cr, Co, Hg, Ni, Mn, Pb, and Zn) were measured in surface sediments at the site. The ignition loss (IL) in the surface sediments showed a mean value of 15.4%, about 1.5 times higher than the mean value of the sediments in the coastal areas of Korea. The chemical oxygen demand (COD) at some disposal sites exceeded 20 mg $O_2/g{\cdot}dry$, which signifies the initial concentration of marine sediment pollutants in Japan. The disposal sites contain higher concentrations of Cr, Cu and Zn than the sediments of bays and estuaries that might be contaminated. The magnitude of both metal enrichment factors (EF) and adverse biological effects suggest that pollution with Cr and Ni occurred due to the dumping of waste in the study area. In addition, the geoaccumulation index (Igeo) showed that the surface sediments were moderately contaminated. By the mid-2000s, when the amount of waste dumped at this site was the highest, the concentration of metallic elements was higher than ever recorded. On the other hand, in 2008-09, the need for environmental management was relatively low compare with the peak. As a result, the quality of marine sediment has been enhanced, considering the effect of waste reduction and natural dilution in the disposal area.

치과용 주조 합금의 방전가공에 따른 표면 성분 변화 (Elemental alteration of the surface of dental casting alloys induced by electro discharge machining)

  • 장용철;이명곤
    • 대한치과기공학회지
    • /
    • 제31권1호
    • /
    • pp.55-61
    • /
    • 2009
  • Passive fitting of meso-structure and super-structures is a predominant requirement for the longevity and clinical success of osseointegrated dental implants. However, precision and passive fitting has been unpredictable with conventional methods of casting as well as for corrective techniques. Alternative to conventional techniques, electro discharge machining(EDM) is an advanced method introduced to dental technology to improve the passive fitting of implant prosthesis. In this technique material is removed by melting and vaporization in electric sparks. Regarding the efficacy of EDM, the application of this technique induces severe surface morphological and elemental alterations due to the high temperatures developed during machining, which vary between $10,000{\sim}20,000^{\circ}C$. The aim of this study was to investigate the morphological and elemental alterations induced by EDM process of casting dental gold alloy and non-precious alloy used for the production of implant-supported prosthesis. A conventional clinical dental casting alloys were used for experimental specimens patterns, which were divided in three groups, high fineness gold alloy(Au 75%, HG group), low fineness gold alloy(Au 55%, LG group) and nonprecious metal alloy(Ni-Cr, NP group). The UCLA type plastic abutment patterns were invested with conventional investment material and were cast in a centrifugal casting machine. Castings were sandblasted with $50{\mu}m\;Al_2O_3$. One casting specimen of each group was polished by conventional finishing(HGCON, LGCON, NPCON) and one specimen of each group was subjected to EDM in a system using Cu electrodes, kerosene as dielectric fluid in 10 min for gold alloy and 20 min for Ni-Cr alloy(HGEDM. LGEDM, NOEDM). The surface morphology of all specimens was studied under an energy dispersive X-ray spectrometer (EDS). The quantitative results from EDS analysis are presented on the HGEDM and LGEDM specimens a significant increase in C and Cu concentrations was found after EDM finishing. The different result was documented for C on the NPEDM with a significant uptake of O after EDM finishing, whereas Al, Si showed a significant decrease in their concentrations. EDS analysis showed a serious uptake of C and Cu after the EDM procedure in the alloys studied. The C uptake after the EDM process is a common finding and it is attributed to the decomposition of the dielectric fluid in the plasma column, probably due to the development of extremely high temperatures. The Cu uptake is readily explained from the decomposition of Cu electrodes, something which is also a common finding after the EDM procedure. However, all the aforementioned mechanisms require further research. The clinical implication of these findings is related with the biological and corrosion resistance of surfaces prepared by the EDM process.

  • PDF