• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.93-93
• /
• 2008

니켈도금은 각종 소지 상에 직접적이고 밀착성이 양호하고, 변색이 적고 방청력이 크며, 경도, 내식성, 내마모성 및 유연성이 우수하다. 또한 최근 활발히 진행되고 있는 광촉매 연구에 $TiO_2$는 우수한 광화학적 안정성, 효과적인 전하분리, 높은 산화 환원력 및 상업적 적용성을 갖기 때문에 니켈도금용액에 $TiO_2$를 첨가하며 복합도금을 행함으로써 니켈이 가지고 있는 기존의 우수한 특성에 $TiO_2$의 광분해 효과를 부과시킴 으로써 그 특성이 한층 더 향상되는 것을 알수있다. 본 연구에서는 수용액전해질과 비수용액 전해질에서의 Ni-$TiO_2$ 복합도금의 특성을 비교 분석해보았다. 동전위(Potentiodynamic)실험 및 순환전위(Cyclic Voltammetry)실험을 하였으며, 도금층의 특성 및 두께는 OM,SEM을 이용하여 분석하였다. 또한 복합도금 촉매 전극에 의한 광분해 효과를 보기 위해서 UV램프를 이용하여 분석하였다.

• 한국염색가공학회지
• /
• 제22권1호
• /
• pp.77-82
• /
• 2010

Highly conductive yarn was successfully obtained using electroless nickel plating method with palladium activation. In the presence of palladium seed on surface of fibers as a catalyst, continuos nickel layer produced on surface of fibers by reducing $Ni${2+}$ ion in the electroless plating bath to $Ni^0$. It was found that the Pd-activation using $SnCl_2$ and $PdCl_2$ to deposit palladium seeds on the surface of fibers plays a key role in the subsequent electroless plating of nickel. It also found that electroless nickel plating on the fibers can induce the nickel-plated $ELEX^{(R)}$ fibers to improve the electrical conductivity of the fibers. The thickness of nickel coating layer on the Pd-activated $ELEX^{(R)}$ fibers and specific conductivity of the fiber were increased through electroless plating time. The temperature of nickel plating bath was very effective to enhance the nickel deposition rate.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.147-151
• /
• 2014

A boron doping process using a boron tri-bromide ($BBr_3$) as a boron source was applied to form a $p^+$ emitter layer on an n-type mono-crystalline CZ substrate. Nitrogen ($N_2$) gas as an additive of the diffusion process was varied in order to study the variations in sheet resistance and the uniformity of doped layer. The flow rate of $N_2$ gas flow was changed in the range 3 slm~10 slm. The sheet resistance uniformity however was found to be variable with the variation of the $N_2$ flow rate. The optimal flow rate for $N_2$ gas was found to be 4 slm, resulting in a sheet resistance value of $50{\Omega}/sq$ and having a uniformity of less than 10%. The process temperature was also varied in order to study its influence on the sheet resistance and minority carrier lifetimes. A higher lifetime value of $1727.72{\mu}s$ was achieved for the emitter having $51.74{\Omega}/sq$ sheet resistances. The thickness of the boron rich layer (BRL) was found to increase with the increase in the process temperature and a decrease in the sheet resistance was observed with the increase in the process temperature. Furthermore, a passivated emitter solar cell (PESC) type solar cell structure comprised of a boron doped emitter and phosphorus doped back surface field (BSF) having Ni/Cu contacts yielding 15.32% efficiency is fabricated.

• Journal of Electrochemical Science and Technology
• /
• 제11권2호
• /
• pp.155-164
• /
• 2020

Here we report our preliminary results about nickel phosphide (Ni-P) electroless coating on the surface of cellulose paper (CP) and its feasibility as the anode for lithium (Li) batteries. In particular, CP can act as a flexible skeleton to maintain the mechanical structure, and the Ni-P film can play the roles of both the anode substrate and the active material in Li batteries. Ni-P films with different P contents were plated uniformly and compactly on the microfiber strands of CP. When they were tested as the anode for Li battery, their theoretical capacity per physical area was comparable to or higher than hypothetical pure graphite and P film electrodes having the same thickness. After the large irreversible capacity loss in the first charge/discharge process, the samples showed relatively reversible charge/discharge characteristics. All samples showed no separation of the plating layer and no detectable micro-cracks after cycling. When the charge cut-off voltage was adjusted, their capacity retention could be improved significantly. The electrochemical result was just about the same before and after mechanical bending with respect to the overall shape of voltage curve and capacity.

• 한국자기학회지
• /
• 제15권3호
• /
• pp.202-206
• /
• 2005

무전해 도금법에 의해 제조된 은 피복 Ni-Zn 페라이트 분말의 전파흡수특성을 조사하였다. 분무건조법 및 소결 고정에 의해 평균입경이 $50{\mu}m$ 정도인 페라이트 구형 분말을 제조하고, 이 분말 위에 은 피막을 무전해 도금법에 의해 코팅하였다. 페라이트 표면에 형성되는 은 피막의 미세조직은 도금욕의 $AgNO_3$의 농도에 따라 민감히 변화하였다. 균일한 은 피막을 얻기 위해 페라이트 분말 20g당 10g/L $AgNO_3$가 필요하였다. 페라이트 분말 표면에 은 피막이 형성됨에 따라 전기저항은 $10^{-2}\~10^{-3}\;\Omega$ 정도까지 감소하였다. 도금 처리되지 않은 순수 페라이트 분말은 400 MHz에서 자기공명을 나타내는 전형적인 자성재료의 특성을 나타내었고, 복소유전율은 실수 항이 35, 허수 항은 거의 0에 가까운 값을 나타내었다. 반면 균일한 은 도금이 이루어진 페라이트 분말은 투자율의 큰 변화 없이 복소유전율 실수항이 35, 허수항이 8 이상으로 매우 크게 증가하였다. 이에 따라 전파흡수체의 두께를 현저히 줄일 수 있었다. 임피던스 정합두께는 C-band대역에서 도금되지 않은 페라이트 분말의 경우 5mm로부터 도금 후 2mm 수준으로 감소하였다.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.423-427
• /
• 1999

Electroplating of 80%Ni permalloy thin plate for magnetic core materials. was studied The convected flow of electrolyte was used for stirring methode. The current density could be increased up to 250mA/$\textrm{cm}^2$ by flow cell. The composition of electroplated layer with vespect to current density and flow rate was investigated and experimental equation to predict the composition was made. How cell yielded more uniform thickness distribution than paddle cell did. The composition distribution was also studied. The thickness was the most important factor to the permeability. The permeability of 5$\mu\textrm{m}$plated permalloy was over 2000 at 1 MHz.

• 한국재료학회지
• /
• 제34권3호
• /
• pp.170-174
• /
• 2024

In this study, we report the microstructural evolution and shear strength of an Sn-Sb alloy, used for die attach process as a solder layer of backside metal (BSM). The Sb content in the binary system was less than 1 at%. A chip with the Sn-Sb BSM was attached to a Ag plated Cu lead frame. The microstructure evolution was investigated after die bonding at 330 ℃, die bonding and isothermal heat treatment at 330 ℃ for 5 min and wire bonding at 260 ℃, respectively. At the interface between the chip and lead frame, Ni₃Sn₄ and Ag₃Sn intermetallic compounds (IMCs) layers and pure Sn regions were confirmed after die bonding. When the isothermal heat treatment is conducted, pure Sn regions disappear at the interface because the Sn is consumed to form Ni₃Sn₄ and Ag₃Sn IMCs. After the wire bonding process, the interface is composed of Ni₃Sn₄, Ag₃Sn and (Ag,Cu)₃Sn IMCs. The Sn-Sb BSM had a high maximum shear strength of 78.2 MPa, which is higher than the required specification of 6.2 MPa. In addition, it showed good wetting flow.

• 한국재료학회지
• /
• 제21권6호
• /
• pp.309-313
• /
• 2011

The power capacitors used as vehicle inverters must have a small size, high capacitance, high voltage, fast response and wide operating temperature. Our thin film capacitor was fabricated by alumina layers as a dielectric material and a metal electrode instead of a liquid electrolyte in an aluminum electrolytic capacitor. We analyzed the micro structures and the electrical properties of the thin film capacitors fabricated by nano-channel alumina and metal electrodes. The metal electrode was filled into the alumina nano-channel by electroless nickel plating with polyethylene glycol and a palladium catalyst. The spherical metals were formed inside the alumina nano pores. The breakdown voltage and leakage current increased by the chemical reaction of the alumina layer and $PdCl_2$ solution. The thickness of the electroless plated nickel layer was 300 nm. We observed the nano pores in the interface between the alumina layer and the metal electrode. The alumina capacitors with nickel electrodes had a capacitance density of 100 $nF/cm^2$, dielectric loss of 0.01, breakdown voltage of 0.7MV/cm and leakage current of $10^4{\mu}A$.

• Journal of Welding and Joining
• /
• 제23권3호
• /
• pp.61-67
• /
• 2005

Since lead (Pb)-free solders for electronics have higher melting points than that of eutectic Sn-Pb solder, they need higher soldering temperatures. In order to decrease the soldering temperature we tried to coat Sn-Bi layer on $Sn-3.5\%Ag$ solder by electroplating, which applies the mechanism of transient liquid phase bonding to soldering. During heating Bi will diffuse into the $Sn-3.5\%Ag$ solder and this results in decreasing soldering temperature. As bonding samples, the 1608 capacitor electroplated with Sn, and PCB, its surface was finished with electroless-plated Ni/Au, were selected. The $Sn-95.7\%Bi$ coated Sn-3.5Ag was supplied as a solder between the capacitor and PCB land. The samples were reflowed at $220^{\circ}C$, which was lower than that of normal reflow temperature, $240\~250^{\circ}C$, for the Pb-free. As experimental result, the joint of $Sn-95.7\%Bi$ coated Sn-3.5Ag showed high shear strength. In the as-reflowed state, the shear strength of the coated solder showed 58.8N, whereas those of commercial ones were 37.2N (Sn-37Pb), 31.4N (Sn-3Ag-0.5Cu), and 40.2N (Sn-8Zn-3Bi). After thermal shock of 1000 cycles between $-40^{\circ}C$ and $+125^{\circ}C$, shear strength of the coated solder showed 56.8N, whereas the previous commercial solders were in the range of 32.3N and 45.1N. As the microstructures, in the solder $Ag_3Sn$ intermetallic compound (IMC), and along the bonded interface $Ni_3Sn_4$ IMC were observed.

• 한국태양에너지학회 논문집
• /
• 제32권4호
• /
• pp.43-50
• /
• 2012

Metal-metal oxide (M-M oxide) cermet solar selective coatings with a double cermet layer film structure were deposited on the Al-deposited glass substrate by using a directed current (DC) magnetron sputtering technology. M oxide (CrO and ZrO) was used as the ceramic component in the cermets, and Cr and Zr used as the metallic components. In addition, black Cr (Cr-$Cr_2O_3$ cermet) solar selective coatings were deposited on the Ni-plated Cu substrate by using a electroplating method for comparison. The thermal stability tests were carried out for performance evaluation of solar coatings. Reflectance measurements were used to evaluate both solar absorptance(${\alpha}$) and thermal emittance (${\epsilon}$) of the solar coatings before and after thermal testing by using a spectrometer. Optical properties of optimized cermet solar coatings were ${\alpha}{\simeq}0.94-0.96$ and ${\epsilon}{\simeq}0.1$ ($100^{\circ}C$). The results of thermal stability test of M-M oxide solar coatings showed that the Cr-CrO cermet solar selective coatings were more stable than the Zr-ZrO cermet selective coatings at temperature of both $400^{\circ}C$ in air and $450^{\circ}C$ in vacuum. The black Cr solar selective coatings were degraded in air at temperature of $400^{\circ}C$. The main optical degradation modes of these coatings were diffusion of metal atoms, and oxidation.