• Journal of the Korean Institute of Navigation
• /
• v.22 no.4
• /
• pp.69-75
• /
• 1998

The super wideband electromagnetic wave absorber in RF-A-PF type has been proposed, which can be used for an anechoic chamber, wall material to prevent TV ghost, etc, In this paper, $Ni_x-Mg_{0.1}-Zn_(1-x-0.1){\cdot}Fe_2O_4$ Ferrite Powder has been fabricated. Using this, then, [$Ni_x-Mg_{0.1}-Zn_(1-x-0.1){\cdot}Fe_2O_4$-Rubber composite for RF-layer in the RF-A-PF type absorber has been fabricated and its characteristics has been analyzed. As a result, it has been shown that the $Ni_x-Mg_{0.1}-Zn_(1-x-0.1){\cdot}Fe_2O_4$-Rubber composit with the quantity $_x$ of $Ni_x$ between 0.5 and 0.6 is suitable for the RF-layer in the case of which the grain size is sub-micrometer order.

• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.195-200
• /
• 2013

Here, we report preparation of cyan ceramic nano-pigment for inkjet printing and the Ni substitutional effects on the cyan color. $MgAl_2O_4$ was selected as the crystalline host network for the synthesis of nickel-based cyan ceramic nano-pigments. Various compositions of $Ni_xMg_{1-x}Al_2O_4$ ($0{\leq}x{\leq}1$) powders were prepared using the polymerized complex method. The powder was then preheated at $400^{\circ}C$ for 5 h and finally calcined at $1000^{\circ}C$ for 5 h. XRD patterns of $Ni_xMg_{1-x}Al_2O_4$ showed a single phase of the spinel structure in all the compositions. The particle sizes ranged from 20 to 50 nm in TEM observations. The characteristics of the color tones of $Ni_xMg_{1-x}Al_2O_4$ were analyzed by UV-Visible spectroscopy and CIE $L^*a^*b^*$ measurement. CIE $L^*a^*b^*$ measurement results indicate that the pigment color changes from light cyan to deep cyan due to the decrease of the $a^*$ and $b^*$ values with an increase of an Ni substitutional amount. In addition, the thermal stability and the binding nature of $Ni_xMg_{1-x}Al_2O_4$ are also discussed using TG-DSC and FT-IR results respectively.

• Journal of the Korean Ceramic Society
• /
• v.28 no.4
• /
• pp.329-337
• /
• 1991

The Ni-MgO composites were prepared by coprecipitation of NiO-MgO solid solutions and their selective reduction in a hydrogen atmosphere. We report on the measurements of both ac conductivity $\sigma$ ($\omega$, f) and dielectric constant $textsc{k}$'($\omega$, f) for the Ni-MgO composites in the frequency range from 10 Hz to 10 MHz at room temperature. The frequency exponents of conductivity and dielectric constant, x and y, are found to be x=0.98$\pm$0.05 and y=0.05$\pm$0.01. These results are in good agreement with a general scaling relation $\chi$-y=1, although these values are different from the theoretical predications. The dielectric constant exponent ($textsc{k}$' f-fc -s) is found to be s=0.62$\pm$0.07 with estimated percolation threshold fc=0.20$\pm$0.02.

• Korean Journal of Metals and Materials
• /
• v.50 no.6
• /
• pp.463-468
• /
• 2012

A 71.5 wt%Mg-23.5 wt%Ni-5 wt%$Fe_2O_3$ (Mg-23.5Ni-$5Fe_2O_3$) sample was prepared by a quite simple process, reactive mechanical grinding, and its hydriding and dehydriding properties were then investigated. The reactive mechanical grinding of Mg with Ni and $Fe_2O_3$ is considered to facilitate nucleation and shorten the diffusion distances of the hydrogen atoms. After the hydriding-dehydriding cycling, the Mg-23.5Ni-$5Fe_2O_3$ sample contained $Mg_2Ni$ phase. Expansion and contraction of the hydride-forming materials (Mg and $Mg_2Ni$) with the hydriding and dehydriding reactions are also considered to increase the hydriding and dehydriding rates of the mixture by forming defects and cracks leading to the fragmentation of the particles. The temperature dependence of the hydriding rate of the sample is discussed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.63-63
• /
• 2018

본 연구는 플라즈마 전해 산화 (PEO) 및 RF (Radio Frequency) 스퍼터링을 이용한 2 단계 접근법에 의해 처리 된 MgO / Ni-Cr의 고내식성 이중층 코팅을 제조하기 위해 수행되었다. 이를 위해 $100mA/cm^2$ 교류 조건에서 180 s PEO를 한 후 150W 에서 900s RF 스퍼터링을 수행 하였다. 코팅의 형태는 주사전자현미경(SEM)을 사용하여 관찰되었으며 코팅의 상조성은 X-선 회절(XRD) 및 X-선 광전자 분광법(XPS)을 사용하여 분석하였다. SEM 이미지는 스퍼터링 된 Ni-Cr이 크랙의 대부분과 미세한 미세 공극을 덮어 코팅 결함이 감소함을 보여 주었다. 따라서, 코팅 된 샘플의 거칠기 값은 스퍼터링 공정 후에 감소되었다. 단면 이미지로부터, 스퍼터링된 코팅층은 낮은 두께 때문에 거의 검출되지 않았다. EDS, XRD 및 XPS를 사용한 조성 분석은 금속 상태의 형태로 Ni 및 Cr 존재를 나타내었고 XPS에서 NiCr2O4 부동태 피막이 검출되었다. MgO / Ni-Cr 이중층 코팅의 내부식성은 MgO / Ni-Cr 이중층을 가진 샘플의 금속 원소와 비교하여 우수한 부식 특성을 나타내는 전위 역학적 분극 시험 및 전기 화학적 임피던스 분광법으로 평가 하였다.

• New & Renewable Energy
• /
• v.4 no.4
• /
• pp.80-87
• /
• 2008

Steam reforming of LPG was investigated over spc-Ni/MgAl catalyst in a temperature range of $600{\sim}850^{\circ}C$, feed molar ratio of $H_2O/C=1.0{\sim}3.0$, space velocity of $10,000{\sim}90,000h^{-1}$ and at atmospheric pressure. spc-Ni/MgAl catalyst was prepared by a co-precipitation method, whereas Ni/MgO and $Ni/Al_2O_3$ catalysts were prepared by an incipient wetness method. The characteristics of catalysts were analyzed by N2 Physisorption, CO chemisorption, XRD, TOF-SIMS, SEM and TEM techniques. The Ni/MgO and $Ni/Al_2O_3$ catalysts were deactivated by the formation of carbon. However, the spc-Ni/MgAl catalyst showed higher conversion and $H_2$ selectivity than the other catalysts, even though carbon was formed on the surface of the catalyst during the reaction under the tested reaction conditions.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.605-609
• /
• 2004

The microstructure, electrical and dielectric characteristics of ZnO varistors were investigated at various metal oxide (NiO, MgO, and Cr$_2$O$_3$) additives. The average grain size was increased with addition of NiO while that was decreased with addition of Cr$_2$O$_3$-Thereby, the varistor voltage was higher in Cr$_2$O$_3$-added composition. Among varistors, the varistor added with Cr$_2$O$_3$ exhibited the highest nonlinearity, with 40.5 in the nonlinear exponent and 2.7 ${\mu}$A in the leakage current and its dielectric dissipation factor was relatively low value of 0.0589.

• Journal of the Korean Ceramic Society
• /
• v.14 no.3
• /
• pp.187-192
• /
• 1977

For the purpose researching to the influence of tetrahedral and octahedral preference of cations of $Ni^{2+}$, $Ti^{4+}$ upon the formation and the color development of the $ZnO-SnO_2$ spinel containing $Ni^{2+}$ and $Ti^{4+}$ ions, the gradual substitution of $Ni^{2+}$ ions for $Zn^{2+}$ ions and of $Ti^{4+}$ ions for $Sn^{4+}$ ions of the spinel in NiO-ZnO-$SnO_2$-$TiO_2$ system was carried out. On samples prepared by calcining the oxide and basic cabonate mixtures at $1300^{\circ}C$ for 2 hours, the X-ray analysis, measurement of reflectance and the test of their stabilaity as a glaze pigment were also carried out. The results are summarized as follows 1) Single spinel was formed completely to x=1 in the $xNiO\cdot(2-x)ZnO\cdot{SnO}_2$system, and gave brilliant lightgreen hue. Moreover, $NiO\cdot{ZnO}\cdot{SnO}_2$ formed easily spinel than $NiO\cdot{MgO}\cdot{SnO}_2$ because Zn^{2+}$ ions had more strong tetrahedral preference than $Mg^{2+}$ ions. 2) As the gradual substitution of $Ti^{4+}$ ions for $Sn^{4+}$ ions in $NiO\cdot{MgO}\cdot{SnO}_2$ system, the spinels formed well and was nearly not changed in the hue. 3) The results of glaze test. (1) As the gradual substitution of $Ni^{2+}$ ions for $Zn^{2+}$ ions, the color changed from dull white to graish broun gradually in calcium-zinc glaze and calcium glaze, and from white to beige in tile glaze. (2) As the gradual substitution of $Ti^{4+}$ ions for $Sn^{4+}$ ions in $NiO-ZnO-SnO_2-TiO_2$ system, the color was become dull generally and was not change in tile glaze.

• Korean Journal of Materials Research
• /
• v.33 no.8
• /
• pp.330-336
• /
• 2023

The effects of Ni²⁺ substitution for Mg²⁺-sites on the microwave dielectric properties of (Mg_1-xNi_x)(Ti_0.95(Mg_1/3Ta_2/3)_0.05)O₃ (0.01 ≤ x ≤ 0.05) (MNTMT) ceramics were investigated. MNTMT ceramics were prepared by conventional solid-state reaction. When the MgO / TiO₂ ratio was changed from 1.00 to 1.02, MgTi₂O₅ was detected as a secondary phase along with the MgTiO₃ main phase in the MNTMT specimens sintered at 1,400 ℃ for 4h. For the MNTMT specimens with MgO / TiO₂ = 1.07 sintered at 1,400 ℃ for 4h, a single phase of MgTiO₃ with an ilmenite structure was obtained from the entire range of compositions. The relative density of all the specimens sintered at 1,400 ℃ for 4h was higher than 95 %. The quality factor (Qf) of the sintered specimens depended strongly on the degree of covalency of the specimens, and the sintered specimens with x = 0.01 showed the maximum Qf value of 489,400 GHz. The dielectric constant (K) decreased with increasing Ni²⁺ content because Ni²⁺ had a lower dielectric polarizability (1.23ų) than Mg²⁺ (1.32ų). As Ni²⁺ content increased, the temperature coefficient of resonant frequency (TCF) improved, from -55.56 to -21.85 ppm/℃, due to the increase in tolerance factor (t) and the lower dielectric constant (K).

• Journal of Korea Foundry Society
• /
• v.28 no.5
• /
• pp.199-203
• /
• 2008

현재 사용되고 있는 진동감쇠능 Mg-Zr 합금인 K1A는 우수한 진동감쇠능을 갖으나 열악한 기계적 특성과 Zr이 고가이면서 고융점 원소로 합금화가 어렵다는 문제점 때문에 진동테이블, 미사일 유도시스템 및 레코딩 장비 등에 소량만 적용되고 있다. Mg-Ni 합금의 경우Ni가 Mg 용탕 내에 고용되지 않아 우수한 진동감쇠능을 갖으나 Fe, Cu등과 함께 Mg의 부식을 가속시키는 원소로 사용이 제한적일 뿐 아니라 Zr과 마찬가지로 Ni도 고융점 원소로 합금화가 어렵다는 것도 문제점으로 작용하고 있다. Mg-Si 합금의 경우 Si이 극소량만 고용되어 우수한 진동감쇠능을 보이며 Ni과 달리 부식에 영향을 받지 않는 원소이지만 Zr, Ni와 마찬가지로 고가이면서 고융점 원소로 합금화가 어렵다는 문제점이 있다. Mg 용탕에 첨가하게 되면 용탕의 표면에 MgO, CaO 피막을 형성하여 발화현상을 억제할 뿐 아리라 첨가량의 증가에 따라 발화온도를 상승시키는 Ca의 경우 Mg 내에 고용되어 진동감쇠능을 감소시킬 뿐 아니라 유동성 저하 및 열간균열을 야기하는 것으로 나타났다. 그러나 CaO의 경우 Mg내에 고용되지 않고, 가격이 저렴하며 Mg 고유 특성의 변화가 적다. 또한 Ca와 같이 Mg 용탕의 발화를 억제하여 보호가스인 $SF_6$를 사용하지 않아도 된다. 이런 다양한 장점을 갖는 CaO를 첨가한 Mg합금이 진동감쇠능을 유지하면서 기계적 특성이 향상된다면 주행 시 안전성 및 정음성이 요구되는 수송기기 분야와 외부충격으로부터 데이터 보호가 필수적인 휴대용 전자정보통신기기 분야에서 적용이 증가할 전망이며 이에 따라 이 분야에 대한 지속적인 연구와 투자가 이루어져야 할 것이다.