• Bulletin of the Korean Chemical Society
• /
• 제31권3호
• /
• pp.635-638
• /
• 2010

As a new strategy for the optimization of a chiral catalyst, the catalytic activity of the host-guest complexes of chiral bisphosphine bearing imidazolidinone was investigated in Rh-catalyzed asymmetric hydrogenation of enamide. Marginal enhancement in enantioselectivity was observed and the nature of interaction between host-guest was experimentally elucidated.

• 한국수소및신에너지학회논문집
• /
• 제15권3호
• /
• pp.244-249
• /
• 2004

Pd catalyst have been used in hydrogenation, oxidation, and low temperature combustion reaction. Recently, it has been candidated as a possible reagents in the partial oxidation of methanol reformers of the fuel cell. Pd catalysts, even though it is very precious and expensive, catalytic functioning is good, but it still need to be improved in the matter of durability and low catalytic activity after calcination. In this study, we synthesize the improved Pd catalyst and study their chemical functioning.

• 한국수소및신에너지학회논문집
• /
• 제21권5호
• /
• pp.383-389
• /
• 2010

Co-B, Co-P-B, Co-Ni-B and Co-Ni-P-B catalysts supported on Ni foam were prepared using electroless plating in the present study. The surface morphology of the catalysts/Ni foam was observed using SEM and EDS analysis. The Co-Ni-P-B/Ni foam catalyst showed the superior performance on hydrogen generation due to the uniform formation of catalyst particles on the Ni foam surface. The characteristics of hydrogen generation with Co-Ni-P-B/Ni foam catalyst was investigated at the variety of $NaBH_4$ and NaOH concentrations. Durability test was performed, resulting in the stable hydrogen generation for 6 hours.

• 한국수소및신에너지학회논문집
• /
• 제21권6호
• /
• pp.519-525
• /
• 2010

Ethanol was used as reductant to remove $NO_x$ over Ag/$Al_2O_3$ catalyst via SCR from stationary emission source. Among the tested hydrocarbon reductants, ethanol showed highest de-$NO_x$ performance over the Ag/$Al_2O_3$ catalyst. De-$NO_x$ efficiency of about 83% was obtained in the condition of GHSV 20,000 $hr^{-1}$, $NO_x$ 200 ppm, CO 200 ppm, $O_2$ 13%, $H_2O$ 5% and mole ratio of ethanol/$NO_x$ = 2 between temperature of $300^{\circ}C$ and $400^{\circ}C$. While $SO_2$ presence in the $NO_x$ exhaust suppressed the catalytic activity, catalyst with acid (0.7% $H_2SO_4$) treatment of catalyst showed higher catalytic activity, where In-Situ DRIFT showed S presence over catalyst surface was increased after acid treatment of catalyst. From in-situ DRIFT and SCR results, it was concluded that sulfur presence over the surface of Ag/$Al_2O_3$ catalyst was the dominant factor to control the de-$NO_x$ reaction yield via HC-SCR from the exhausted gas including $SO_2$.

• 한국수소및신에너지학회논문집
• /
• 제26권4호
• /
• pp.339-346
• /
• 2015

The synthesis of Fischer-Tropsch (FT) oil is the catalytic hydrogenation of CO to give a range of products, which can be used for the production of high-quality diesel fuel, gasoline and linear chemicals. This studied catalyst was prepared Cobalt-supported alumina and silica by the incipient wet impregnation of the nitrates of cobalt, promoter and organic solvent with supports. Cobalt catalysts were calcined at $350^{\circ}C$ before being loaded into the FT reactors. After the reduction of catalyst has been carried out under $450^{\circ}C$ for 24h, FT reaction of the catalyst has been carried out at GHSV of 4,000/hr under $200^{\circ}C$ and 20atm. From these experimental results, we have obtained the results as following; In case of $SiO_2$ catalysts, the activity of 12wt% $Cobalt-SiO_2$ synthesized by organic solvent was about 2 or 3 times higher than the activity of 12wt% $Cobalt-SiO_2$ catalyst synthesized without organic solvent. In particular, the activity of the $Cobalt-SiO_2$ catalyst prepared in the presence of an organic solvent P was two to three times higher than that of the $Cobalt-SiO_2$ catalyst prepared without the organic solvent. Effect of Cr and Cu metal as a promoter was found little. 200 h long-term activity test was performed with a $Co/SiO_2$ catalyst prepared in the presence of an organic solvent of Glyoxal solution.

• 한국수소및신에너지학회논문집
• /
• 제24권6호
• /
• pp.535-542
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effect of bed insert geometry on CO conversion of WGS catalyst was measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and tablet shaped WGS catalyst and sand particle were used as bed materials. The cylinder type and the spring type bed inserts were used to hold the WGS catalysts. The CO conversion of WGS catalyst with the change of steam/CO ratio was determined based on the exit gas analysis. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. The measured CO conversion using the bed inserts showed high value comparable to previous results even though at low catalyst content. Most of input gas flowed through the bed center side when we charged tablet type catalyst into the cylinder type bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. However, the spring type bed insert showed good reactivity and good distribution of gas, and therefore, the spring type bed insert was selected as the best bed insert for SEWGS process.

• 한국수소및신에너지학회논문집
• /
• 제27권3호
• /
• pp.283-289
• /
• 2016

In this study, electrochemical characterizations of PdCu/C catalysts that are synthesized by modified polyol method are investigated. Most of all, amount of ethylene glycol (EG) that is used as main component for catalyst synthesis is mainly modulated to optimize synthetic condition of the PdCu/C catalyst, For evaluations about catalytic activity and performance of direct formic acid fuel cell (DFAFC), half cell and full cell tests are implemented. As a result, when amount of EG is 4M, catalytic activities of the PdCu/C catalyst such as peak current of formic acid oxidation and active surface area are best, while maximum power density of DFAFC using the optimized PdCu/C catalyst is better than that using commercial Pd/C (30 wt%) by 6%. Based on that, PdCu/C catalyst synthesized by modified polyol method plays a critical role in improving (i) catalytic activity for formic acid oxidation and (ii) DFAFC performance by employing as anodic catalyst.

• 한국수소및신에너지학회논문집
• /
• 제34권5호
• /
• pp.535-548
• /
• 2023

The intermittent nature of renewable energy is a challenge to overcome for safety and stable performance in water electrolysis systems linked to renewable energy. Oxygen removal using the catalyst is suitable for maintaining the oxygen concentration in hydrogen below the explosive level (4%) even in intermittent power supply. Metals such as Pd, Pt, and Ni are expected to be effective materials due to their hydrogen affinity. The oxygen removal performance was compared under high hydrogen concentration conditions by loading on γ-Al₂O₃ with high reactivity and large surface area. The characteristics of the catalyst before and after the reaction were analyzed through X-ray diffraction, transmission electron microscope, H₂-temperature programmed reduction, X-ray photoelectron spectroscope, etc. The Pd catalyst that showed the best performance was able to lower 2% oxygen to less than 5 ppm. Changes in catalyst characteristics after the reaction indicate that oxygen vacancies are related to oxygen removal performance and catalyst deactivation.

• 한국수소및신에너지학회논문집
• /
• 제24권2호
• /
• pp.150-159
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effects of insert geometry and shape of WGS catalysts on CO conversion were measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and WGS catalyst (particle and tablet) and sand were used as bed materials. The parallel wall type and cross type bed inserts were used to hold the WGS catalysts. The CO conversion with steam/CO ratio was determined based on the exit gas analysis. The measured CO conversion using the bed inserts showed high value comparable to physical mixing cases. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. Most of input gas flowed through the catalyst side when we charged tablet type catalyst into the bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. New bed insert geometry was proposed based on the results from this study to enhance contact between input gas and WGS catalyst and $CO_2$ absorbent.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.63-66
• /
• 2007

Reformers which produce hydrogen from natural gas are essential for the operation of residential PEM fuel cells. For this purpose, steam-methane reforming reactions with Ni catalysts is primarily utilized. Commercial Ni catalysts are generally made to have porous pellet shapes in which Ni catalyst particles are uniformly dispersed over Alumina support structures. This study numerically investigates the reduction of catalyst effectiveness due to the mass transport resistances posed by porous structures of spherical catalyst pellets. The multi-component diffusion through porous media and the accurate kinetics of reforming reaction is fully considered in the numerical model. The preliminary results on the variation of the effectiveness factor according to different operation conditions are presented, which is planned to be used to develop correlations in future studies.