• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.193-195
• /
• 2007

These days, to change the new & renewable energy change the subject because environmental pollution and exhausted fossil power. The most notable Fuel cells by one of the new & renewable energies are one of very useful power conversion sources. Their advantages are low environmental pollution, highly efficient power generation, diversity of fuels (natural gas, LPG, methanol and naphtha), and reusability of exhaust heat, modularity, and faster installation. PEMFC by one of the Fuel Cells is the energy of new technology which is produced by the electric chemical reaction directly. The essential composition elements of PEMFC stack are membrane electrode assembly (MEA), catalyst, Bipolar Plate. Under the this study, know-how is manufacturing single cell of PEMFC and Study design of Low Voltage, Low Electric Power System by PEMFC Single Cell.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.2
• /
• pp.211-218
• /
• 2009

This paper presents a voltage and frequency controller (VFC) for a 4-wire stand-alone wind energy conversion system (WECS) employing an asynchronous generator. The proposed VF con-troller consists of a three leg IGBT (Insulated Gate Bipolar Junction Transistor) based voltage source converter and a battery at its DC bus. The neutral terminal for the consumer loads is created using a T-connected transformer, which consists of only two single phase transformers. The control algorithm of the VF controller is developed for the bidirectional flow capability of the active power and reactive power control by which it controls the WECS voltage and frequency under different dynamic conditions, such as varying consumer loads and varying wind speeds. The WECS is modeled and simulated in MATLAB using Simulink and PSB toolboxes. Extensive results are presented to demonstrate the capability of the VF controller as a harmonic eliminator, a load balancer, a neutral current compensator as well as a voltage and frequency controller.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.569-577
• /
• 2005

In this paper, a new control scheme to use 6-switch IGBI module for 3-phase switched reluctance motors(SRM) is proposed. Compared with the conventional asymmetric bridge converter topology, it can minimize the entire system size and cost. Therefore, it may have a new topology lot SRM to compare the other ac motors, such as induction motors, brushless dc motors, and so on. The validity of the proposed method is verified by simulation, and experimental results.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.6
• /
• pp.530-545
• /
• 2020

This paper reviews and summarizes the fuel-cell-related studies those have been recently published in major Korean Citation Index journals, aiming at analyzing the research trend in fuel cell technologies. Six major journals are selected for the literature survey; 57 papers are chosen for the detailed analysis through a screening examination on the total 1,040 papers published during between 2018 and 2020. Papers are classified into six technical categories, such as i) electrode, ii) electrolyte, iii) bipolar plate and stack, iv) fuel cell system, v) balance of plant, and vi) diagnosis-related studies, and summarized by the experts in the relevant area. Through this paper, we provide a comprehensive review on the recent trends and progress in fuel-cell-related research work in Korea.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2519-2523
• /
• 2003

Ultrasonic sensors are widely used in mobile robot applications to recognize external environments, because they are cheap, easy to use, and robust under varying lighting conditions. In most cases, a single ultrasonic sensor is used to measure the distance to an object based on time-of-flight (TOF) information, whereas multiple sensors are used to recognize the shape of an object, such as a corner, plane, or edge. However, the conventional sequential driving technique involves a long measurement time. This problem can be resolved by pulse coding ultrasonic signals, which allows multi-sensors to be fired simultaneously and adjacent objects to be distinguished. Accordingly, the current presents a new simultaneous coded driving system for an ultrasonic sensor array for object recognition in autonomous mobile robots. The proposed system is designed and implemented using a DSP and FPGA. A micro-controller board is made using a DSP, Polaroid 6500 ranging modules are modified for firing the coded signals, and a 5-channel coded signal generating board is made using a FPGA. To verify the proposed method, experiments were conducted in an environment with overlapping signals, and the flight distances for each sensor were obtained from the received overlapping signals using correlations and conversion to a bipolar PCM-NRZ signal.

• Journal of Biomedical Engineering Research
• /
• v.16 no.1
• /
• pp.107-113
• /
• 1995

It is well known that multipoint and computerized intraoperative mapping systems improve the results of surgery for Wolff-Parkinson-White syndrome and show tremendous potential for opening an entirely new era of surgical intervention for the more common and lethal types of supraventricular tachyarrhythmias such as atrial flutter and atrial fibrillation. In addition, the ability to map and ablate the sometimes fleeting automatic atrial tachycardia is greatly enhanced by computerized mapping systems. In this study, we have developed 64 channel computerized data analysis system using microcomputer (Macintosh ${II}_{x}$) for basic research of electrophysiology and electrical propagation. The bipolar electrogram information is acquired from 64 cardiac sites simultaneously at a sampling rate of 1 ksampls/sec with continuous and total data storage of up to 30 seconds. When the reference electrogram is selected and reference point is picked up, delay time from the reference point is displayed on two dimensional diagram of the heart. System design permits easy expansion to almost 256 simultaneous sites. this system is expected to enable us to study pathophysiology of cardiac arrhythmia and to improve the result of diagnosis and surgical treatment for cardiac arrhythmia.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.11
• /
• pp.1028-1036
• /
• 2004

Ultrasonic sensors are widely used in mobile robot applications to recognize external environments by virtue that they are cheap, easy to use, and robust under varying lighting conditions. In most cases, a single ultrasonic sensor is used to measure the distance to an object based on time-of-flight (TOF) information, whereas multiple sensors are used to recognize the shape of an object, such as a comer, plane, or edge. However, the conventional sequential driving technique involves a long measurement time. This problem can be resolved by pulse coding of ultrasonic signals, which allows multi-sensors to be emitted simultaneously and adjacent objects to be distinguished. Accordingly, this paper presents a new simultaneous coded driving system for an ultrasonic sensor array for object recognition in autonomous mobile robots. The proposed system is designed and implemented. A micro-controller unit is implemented using a DSP, Polaroid 6500 ranging modules are modified for firing the coded signals, and a 5-channel coded signal generating board is made using a FPGA. To verify the proposed method, experiments were conducted in an environment with overlapping signals, and the flight distances fur each sensor were obtained from the received overlapping signals using correlations and conversion to a bipolar PCM-NRZ signal.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.138.1-138.1
• /
• 2010

직접메탄올 연료전지는 액체 메탄올 저장의 이점을 가지고 있어 이동형 전원 등의 응용에 적합하며, 최근 군사용 통신 전원이나 노트북용 전원으로 사용하기 위한 연구가 활발히 진행 중이다. 그러나 연료전지 스스로는 초기 기동을 할 수 없고 부하의 응답 특성에 빠르게 대응하기 어렵다. 따라서 연료전지와 배터리를 하이브리드로 구성하면 이러한 문제를 해결할 수 있을 뿐만 아니라 연료전지에 대한 부하가 안정되어 수명 연장에도 긍정적인 효과를 얻을 수 있다. 본 연구에서는 직접메탄올 연료전지와 리튬 이차전지를 연계하여 하이브리드 시스템을 구성하고자한다. 시뮬레이션을 통해 채널 형상에 따른 유동 및 차압을 해석하였으며, Single Cell, Short Stack 및 Stack의 특성을 평가하였다. 또한 하이브리드 시스템은 연료전지 스택, 연료전지 운전 장치, 리튬 이차전지, BMS, PCM, DC/DC Converter 등을 구성하여 시스템의 특성 등을 관찰하고자한다.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1438-1444
• /
• 2007

Standard Gate Turn Off (GTO) Thyristor drive technology results in inhomogeneous turn-on and turn-off transients which in turn needs costly dv/dt and di/dt snubber circuits. Added to this GTO is bulky in size, needs external cooling, slower switching time etc. The development of high voltage Insulated Gate Bipolar Transistor (IGBT) have given new device advantage in the areas where they compete with conventional GTO technology. Indian Railway has developed first IGBT based traction converter and was commissioned in November 2006. Some of the supremacy of IGBT are smaller in size, no external cooling is required, built in power supply which enhances reliability, lower switching losses which leads to higher efficiency, reduced gate drive, high frequency operation in real time etc. These advantages are highlighted along with IGBT Traction system in operation.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.9
• /
• pp.662-664
• /
• 1999

We fabricated AC-TFEL device having cone-shaped Si micro-tip reflector array based on the process which have been conventionally employed for the Si-tip field emitter array in FED system. As a result, the AC-TFEL device having a new geometrical structure could generate well concentrated visible white-light from 3600 reflectors/pixel under bipolar pulse excitation mode only by edge-emission mechanism.