• 대한조선학회논문집
• /
• 제53권1호
• /
• pp.18-28
• /
• 2016

In shipbuilding, the scheduling system is susceptible to sudden changes and thus it turns to be difficult to predict the differences between schedule and production records in advance. A computer-based simulation is commonly utilized to overcome the discrepancies occurred in estimating workloads and resulting processing times. The main drawback of this simulation-based solution is its limited applicability because, in most cases, each shipyard requires specific and customized simulation environment. By standardizing the planning data of the midterm scheduling system, as proposed in this paper, the efficiency of the current simulation model can be enhanced. To present an alternative approach, this paper begins with the analysis of the complex planning data structure of several shipyards and then proceeds to construct a standard data structure based on the neutral format. An interface application is developed for the data transaction and simulation in on-line environment. As a result, a simulation-based production management of shipyards can be achieved by the efficient prediction of planning and scheduling.

• 전기학회논문지
• /
• 제61권12호
• /
• pp.1953-1958
• /
• 2012

The major causes of electrical fire are classified to short circuit fault, overload fault, electric leakage and electric contact failure. The occurrence factor of the fire is electric arc or spark accompanied with such electric faults, specially short circuit faults. Earth Leakage Circuit Breaker (ELB) and Molded_case Circuit Breaker (MCCB), that is, Residual Current Protective Devices (RCDs) used on low voltage distribution lines cut off earth leakage and overload, but the RCD can not cut off electric arc or spark to be a major factor of electrical fire. As the RCDs which are applied in low voltage distribution panel are prescribed to rated breaking time about 30ms(KS C 4613), the RCDs can't perceive to the periodic electric arc or spark of more short wavelength level. To improve such problem, this paper proposes a prevention apparatus using the line voltage drop of neutral wire and some semiconductor switching devices. Some experimental tests of the proposed apparatus confirm the validity of the analytical results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.475-478
• /
• 2001

In performing the three-level SVPWM, it is nearly impossible to control the neutral-point potential exactly to the half of the dc-link voltage at all times. Therefore the inverter would produce an erroneous output voltage by this voltage unbalance. So the voltage unbalance has to be compensated in doing PWM, when the voltage unbalance occurs whether it is small or large, to make the inverter output voltage follow the reference voltage exactly the same. In this paper, a new compensating method for the neutral-point potential variation in a three-level inverter space vector PWM (SVPWM) is presented. By using the proposed method, the output voltage of the inverter can be made same as the reference voltage and thus the current and torque ripple of the inverter driven motor can be greatly improved even if the voltage unbalance is quite large. The proposed method is verified experimentally with a 3-level IGBT inverter.

• Journal of Power Electronics
• /
• 제19권4호
• /
• pp.968-979
• /
• 2019

Recently, there has been increased interest in the study of multiphase machines due to their higher fault-tolerant capability when compared to their conventional three-phase counterparts. For six-phase machines, stator windings configured with a single isolated neutral (1N) provide significantly more post-fault torque/power than two isolated neutrals (2N). Hence, this configuration is preferred in applications where post-fault performance is critical. It is well known that min-max injection has been commonly used for three-phase and multiphase machines in healthy condition to maximize the modulation limit. However, there is a lack of discussion on min-max injection for post-fault condition. Furthermore, the effects in terms of the common-mode voltage (CMV) in modulating signals has not been discussed. This paper investigates the effect of min-max injection in post fault-tolerant control on the voltage and speed limit of a symmetrical six-phase induction machine with single isolated neutral. It is shown that the min-max injection can minimize the amplitude of reference voltage, which maximizes the modulation index and post-fault speed of the machine. This in turn results in a higher post-fault power.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2003년도 가을 학술논문집
• /
• pp.689-695
• /
• 2003

Electrochemical decontamination process has been applied for recycle or self disposal with authorization of large amount of metallic wastes contaminated with uranium compounds such as $UO_2$, ammonium uranyl carbonate (AUC), ammonium di-uranate (ADU), and uranyl nitrate(UN) with tributylphosphate(TBP) and dodecane, which are generated by dismantling the contaminated system components and equipment of a retired uranium conversion plant in Korea Atomic Energy Research Institute (KAERI). Electrochemical decontamination for metallic wastes contaminated with uranium compounds was evaluated through the experiments on the electrolytic dissolution of stainless steel as the material of the system components in neutral salt electrolytes. The effects of type of neutral salt as the electrolyte, current density, and concentration of electrolyte on the dissolution of the materials were evaluated. Decontamination performance tests using the specimens taken from a uranium conversion plant were quite successful with the application electrochemical decontamination conditions obtained through the basic studies on the electrolytic dissolution of structural material of the system components.

• Corrosion Science and Technology
• /
• 제12권1호
• /
• pp.40-49
• /
• 2013

Effects of magnesium and pH on corrosion of aluminum galvanically coupled to iron have studied by using potentio- dynamic and static tests for polarization curves, Mott-Schottky test for analysis of semiconductor property, and GD-AES and XPS for film analysis. Pitting potential was sensitive to magnesium as an alloying element but not to pH, while passive current was sensitive to pH but not to magnesium. It was explained with, instead of point defect model (PDM), surface charge model describing that the ingression of chloride depends on the state of surface charge and passive film at film/solution interface is affected by pH. In addition, galvanic current of aluminum electrically coupled to iron was not affected by magnesium in pH 8.4, 0.2M citrate solution but was increased by magnesium at the solution of pH 9.1. The galvanic current at pH 9.1 increased with time at the initial stage and after the exposure of about 200 minute, decreased and stabilized. The behavior of the galvanic current was related with the concentration of magnesium at the surface. It agreed with the depletion of magnesium at the oxide surface by using glow discharge atomic emission spectroscopy (GD-AES). In addition, pitting potential of pure aluminum was reduced in neutral pH solution where chloride ion maybe are competitively adsorbed on pure aluminum. It was confirmed by the exponential decrease of pitting potential with log of [$Cl^-$] around 0.025 M of [$Cl^-$] and linear decrease of the pitting potential. From the above results, unlike magnesium, alloying elements with higher electron negativity, lowering isoelectric point (ISE), are recommended to be added to improve pitting corrosion resistance of aluminum and its alloys in neutral solutions as well as their galvanic corrosion resistance in weakly basic solutions.

• 조명전기설비학회논문지
• /
• 제22권8호
• /
• pp.18-25
• /
• 2008

본 논문은 HATLAB/Simulink에서 계통연계 풍력발전시스템의 특성해석을 위한 모델링을 제안하여 시뮬레이션을 수행한다. 이를 위해 풍속의 변화에 따른 발전기의 출력제어를 위해 피치제어를 수행하며, 연계변압기의 결선방법에 따른 고장전류의 변화를 살펴봄으로 하여 연계변압기의 결선방법과 고장전류와의 상관관계를 제시하였다. 아울러 풍력발전시스템의 연계변압기 중성점접지방식이 고장전류에 미치는 영향을 살펴본다. 계통에서의 1선 지락고장에 대해 연계변압기의 4가지 결선방식의 차이에 따른 고장전류, 전압 및 발전기의 특성 변화를 확인할 수 있었으며 중성점 접지방식의 차이에 따른 고장전류의 변화를 확인하였다. 사례연구를 통하여 제안한 Simulink에서의 시뮬레이션 모델의 효용성을 입증하였다.

• 한국산업정보학회:학술대회논문집
• /
• 한국산업정보학회 1999년도 추계공동학술대회 논문집:21세기지식경영과 정보기술
• /
• pp.121-129
• /
• 1999

통신망을 통하여 시간 연속(continuous) 미디어를 전송하면 통신망의 부하 변동에 따라 운송지연(transit delay)이 일정하지 않으므로 수신측에 도착하는 패킷간에 원래의 시간 관계가 유지되지 않는 비동기 현상이 나타난다. 현재 제안된 여러 동기화 방안들은 운송 지연 특성을 보장하는 자원 보장형 통신망과 운송 지연 특성이 보장되지 않아 변화의 폭이 큰 자원 비보장형 통신망 환경을 고려한 2가지 형태가 존재한다. 자원 보장형 통신망은 최소 및 최대 운송 지연 시간을 예약이나 협상을 통해 전송 기간동안 계속 유지하는 반면, 자원 비보장형 통신망에서는 가능한 최대의 대역폭을 사용하는 최대 노력 (best-effort) 서비스를 사용한다. 이 논문은 패킷망이나 인터넷과 같은 자원 비보장형 통신망 환경에서 통신망의 부하 변화에 동적으로 적응하여 동기화된 전달(playout)을 제공하는 미디어내 동기화 방안(Inter-media Synchronization)에 관한 것이다. 본 논문에서 제안하는 방안은 데이터 전송 경로의 운송 지연 통계치를 사용하여 다음 전송할 패킷의 운송 지연을 추정하여 송신 시간을 조절함으로써, 통신망의 부하로 인한 운송 지연의 변화가 크더라도 수신 패킷의 도착 시간을 일정한 범위 내로 유지한다. 또한, 통신망의 부하가 지속적으로 증가하여 연속되는 패킷의 운송 지연이 점차 늘어나면 전송률을 높이는 것만으로 문제를 해결할 수 없을 뿐만 아니라 오히려 혼잡을 발생시킬 가능성이 있다. 따라서, 통신망의 대역폭에 맞추어 일부 전송 패킷을 폐기함으로써 실제적인 전송률을 조정하였다. 이 방안은 수신측의 버퍼가 충분하지 않거나, 버퍼 지연 시간이 제한적인 대화형 응용에서 연속 미디어를 전송하는데 적합하다.았으며 tall fescue는 T, V, V + T(1 : 1로 피복한 종자)에서 가장 높게 나타났다(P<0.01). 종자피복에 있어서 red clover와 tall fescue 공히 접착제는 CF나 PVA로 하고 고형물질은 V나 V+T(1:1)로 피복함으로서 가장 좋은 피복효과를 얻을 수 있었다.. 쟁점 및 과제들이 제시되었다. cells of these species contained considerable to large amount of neutral mucin, and small to considerable amount of acid mucin, Most of the medium sized and small mucous cells contained neutral mucin and sialomucin, but a few mucous cells contained neutral mucin and strongly sulfomucin or neutral combined with strongly sulfomucin and sialomucin. Most of the esophageal mucous cells pf Bryzoichthys lysimus contained small amount of neutral mucin, while on the other hand a feww mucous cells contained small amount of neutral mucin and minimal amount of sialomucin. But the esophageal mucous cells of Takifugu pardalis contained considerable amount of neutral mucin only.분해가 더욱 촉진

• 한국초전도ㆍ저온공학회논문지
• /
• 제25권4호
• /
• pp.19-23
• /
• 2023

The Second-generation high-temperature superconducting (HTS) Rare-Earth Barium Copper Oxide (REBCO) wire is a composite laminate having a multi-layer structure (8 or more layers). HTS wires will undergo multiple loads including the bending-tension loads during winding, high current density, and high magnetic fields. In particular, the wires are subjected to bending stress and magnetic field stress because HTS wires are wound around a circular bobbin when making a high-field magnetic. Each of the different laminated wires inevitably exhibits damage and fracture behavior of wire due to stress deformation, mismatches in thermal, physical, electrical, and magnetic properties. Therefore, when manufacturing high-field magnets and other applications, it is necessary to calculate the stress-strain experienced by high-temperature superconducting wire to present stable operating conditions in the product's use environment. In this study, the finite element model (FEM) was used to simulate the strain-stress characteristics of the HTS wire under high current density and magnetic field, and bending loads. In addition, the result of obtaining the neutral axis of the wire and the simulation result was compared with the theoretical calculation value and reviewed. As a result of the simulation using COMSOL Multiphysics, when a current of 100 A was applied to the wire, the current value showed the difference of 10^-9. The stress received by the wire was 501.9 MPa, which showed a theoretically calculated value of 500 MPa and difference of 0.38% between simulation and theoretical method. In addition, the displacement resulted is 30.0012 ㎛, which is very similar to the theoretically calculated value of 30 ㎛. Later, the amount of bending stress by the circular mandrel was received for each layer and the difference with the theoretically obtained the neutral axis result was compared and reviewed. This result will be used as basic data for manufacturing high-field magnets because it can be expanded and analyzed even in the case of wire with magnetic flux pinning.

• 전기학회논문지
• /
• 제62권11호
• /
• pp.1604-1609
• /
• 2013

When the ground fault on the power side occurs on distribution system interconnected with distributed generations, the abnormal current is generated in the neutral conductor by the connection type and the iron core structure of transformers for the interconnection of distributed power supplies due to the unbalanced voltage of the system, and subsequently the false operation of the protective relay on the load side occurs. Herein, this paper proposes the method to correct errors in the phase current to prevent the false operation of the protective relay by applying p-q theory and presents the simulation result of the error correction algorithm using PSCAD/EMTDC.