• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.3
• /
• pp.129-134
• /
• 2018

Herein, we report the manufacture of high-performance, ambipolar organic field-effect transistors (OFETs) and complementary-like electronic circuitry based on a blended, polymeric, semiconducting film. Relatively high and well-balanced electron and hole mobilities were achieved by incorporating a small amount of ionic additives. The equivalent P-channel and N-channel properties of the ambipolar OFETs enabled the manufacture of complementary-like inverter circuits with a near-ideal switching point, high gain, and good noise margins, via a simple blanket spin-coating process with no additional patterning of each active P-type and N-type semiconductor layer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.943-953
• /
• 2007

In this paper, we propose a Cassegrain antenna with a scalar feed horn opt rating in Ka-band. For an effective EM simulation of the Cassegrain antenna, the near-field of the feed hone is used ai the equivalent source of the Cassegrain antenna using the surface equivalent theorem. A corrugated circular horn operating with $HE_{11}$ mode is used as the feed horn. The angle and feed center of the main and sub reflectors are optimized to achieve maximum antenna efficiency. The designed feed horn shows the gain of 19dBi, the side-lobe level of less than -25dB and the half power beam width of $20^{\circ}$ at 33 GHz. The Cassegrain antenna shows the gain of 41dBi, the efficiency of 60%, the side-lobe level of less than -20dB and the half power beam width of $1.2^{\circ}$.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.162-170
• /
• 2022

In this paper, the phased-array transceiver (TRX) channel amplitude and phase calibration method for a radar wind profiler (RWP) based on the 256 active phased array is discussed. Without the additional module, the TX and RX calibration paths were secured using couplers and switches in the TRX front ends and the TRX switching duplexers, and the amplitude and phase of the 256 TRX were calibrated using a gain and phase detector. The beam widths and side lobes of five beams (vertical, east, west, south, and north) of the calibrated 256 active phased array antenna were confirmed by a near-field which agreed well with the simulation results. The proposed calibration method can be easily applied to a system based on an active phased array operated in an outdoor environment.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.97-100
• /
• 2007

Recently, there is developed various antenna's models due to increment of wireless communication the need of quantitative study on antenna's measuring technology gets to highlight. In this paper, we propose algorithm of antenna's edge alignment for making automatic measuring system of antenna's characteristics of near-field measurement system of antenna. The proposed algorithm gets the bottom image of antenna from camera, extracts antenna object, and finds the boundary the object. The proposed algorithm calculates distortion of the object using the extracted boundary and the angle to correct this. The proposed algorithm is applied to the standard gain horn antenna. The results show that antenna's object is efficiently extracted and the angle for correcting the error is calculated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.4
• /
• pp.109-119
• /
• 2000

PVDF film sensor was applied to measure the stress concentration for monitoring the structural integrity. The strain calibration of this film sensor was performed by the bending test of aluminum beam. The PVDF sensor and the electrical strain gage were bonded on the beam. When the beam was loaded, the output of electrical strain gage was compared with the output of the PVDF sensor. The waveform of PVDF sensor output was shown as the same form of the output of electrical strain gage. The gain was determined as 1.7 by comparing these two signals to determine the exact value of the strain. In order to experiment the stress concentration, the stress field was analyzed by finite element analysis. The tensile test of notched steel specimens was conducted to develop the measurement technique of stress concentration. The output voltage ratio between the PVDF sensor near the notch and the PVDF sensor far from the notch could give the information about the load bearing capacity of steel specimen.

• Smart Structures and Systems
• /
• v.20 no.1
• /
• pp.61-74
• /
• 2017

One of the most reliable and simplest tools for structural vibration control in civil engineering is Tuned Mass Damper, TMD. Provided that the frequency and damping parameters of these dampers are tuned appropriately, they can reduce the vibrations of the structure through their generated inertia forces, as they vibrate continuously. To achieve the optimal parameters of TMD, many different methods have been provided so far. In old approaches, some formulas have been offered based on simplifying models and their applied loadings while novel procedures need to model structures completely in order to obtain TMD parameters. In this paper, with regard to the nonlinear decision-making of fuzzy systems and their enough ability to cope with different unreliability, a method is proposed. Furthermore, by taking advantage of both old and new methods a fuzzy system is designed to be operational and reduce uncertainties related to models and applied loads. To design fuzzy system, it is required to gain data on structures and optimum parameters of TMDs corresponding to these structures. This information is obtained through modeling MDOF systems with various numbers of stories subjected to far and near field earthquakes. The design of the fuzzy systems is performed by three methods: look-up table, the data space grid-partitioning, and clustering. After that, rule weights of Mamdani fuzzy system using the look-up table are optimized through genetic algorithm and rule weights of Sugeno fuzzy system designed based on grid-partitioning methods and clustering data are optimized through ANFIS (Adaptive Neuro-Fuzzy Inference System). By comparing these methods, it is observed that the fuzzy system technique based on data clustering has an efficient function to predict the optimal parameters of TMDs. In this method, average of errors in estimating frequency and damping ratio is close to zero. Also, standard deviation of frequency errors and damping ratio errors decrease by 78% and 4.1% respectively in comparison with the look-up table method. While, this reductions compared to the grid partitioning method are 2.2% and 1.8% respectively. In this research, TMD parameters are estimated for a 15-degree of freedom structure based on designed fuzzy system and are compared to parameters obtained from the genetic algorithm and empirical relations. The progress up to 1.9% and 2% under far-field earthquakes and 0.4% and 2.2% under near-field earthquakes is obtained in decreasing respectively roof maximum displacement and its RMS ratio through fuzzy system method compared to those obtained by empirical relations.

• Proceedings of the Korean Society of Grassland Science Conference
• /
• 2002.09b
• /
• pp.5-56
• /
• 2002

The problems in the current domestic forage production were evaluated, and the prospective improvement was suggested in this paper. Grassland development in forest, production of high quality forages in upland and paddy land, efficient utilization of rice straw, development of new varieties of forages suitable for our environmental conditions and imported forages were described Among them, preferential production and utilization of forages using paddy field after rice harvest . should be enlarged for domestic supply of forages in Korea. Several studies were carried out to select the promising forage crops and barley cultivars for whole crop silage production, to determine productivity, nutritive value and production cost of forages produced in paddy field, and feeding effect of forages with Hanuwoo and milking cow for whole crop silage with forages produced in paddy field, 1999 to 2001, and also discussed restraint factors and activation plans for enlargement of forage production in paddy land. The promising forage crops in paddy field were rye and barley for Middle region, and rye, barley, early maturing Italian ryegrass and wheat for Southern region. The promising barley cultivars for whole crop silage in paddy field were Albori in Suwon, Keunalbori, Milyang 92, Saessalbori, and Naehanssalbori in Iksan, and Keunalbori, Albori, Naehanssalbori, and Saegangbori in Milyang, respectively. Silage production, quality and animal palatability of silage by trench and round bale were also compared. The production yields of whole crop barley silage(WBS) were 17,135kg as a fresh matter, and 6,011kg as a dry matter per ha, and the quality of WBS was 2∼3 grade, while that of rice straw silage was 4 grade as a farm basis. The production cost of WBS per kg was 83won as a fresh matter, and 238won as a dry matter. Feeding of WBS as forages on Hanwoo was very desirable for the improvement of live-weight gain, beef quality and farm income, particularly in growing stage of Hanwoo. Milk production and income were also increased, and feed cost was decreased by feeding of WBS. The daily voluntary intake of WBS in milking cow was 26.3kg as a fresh matter(DM 7.7kg) per head. Milk production when WBS was fed, was very similar to that of imported hay feeding such as Kentucky bluegrass or domestic corn silage. The issues to be solved in near future f3r stable forage production and supply in paddy land are sustainable livestock-forages policy, development & seed production of new varieties of barley, rye, Italian ryegrass and other promising forages, efficient demand & supply system of forages, solidification for mass production and utilization of forages, efficient application management of animal slurry on paddy field considering environmental agriculture/livestock industry, and break k development of bottleneck technique in production field. Domestic production & supply of high cost agricultural machine (round baler, wrapper, handler and so on), plastic wrapping film, and silage additives are also important.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.454-463
• /
• 2000

A method is presented to alter the geometry of the conventional linearly shaped wire antenna for increasing its bandwidth. The synthesis is two-demensionally symmetric and is based on the minimization of frequency-dependence of the boresight far-field electric field intensity. The current distribution on the wire is calculated by Galerkin method using pulse functions. The shaping limitation for wide-band characteristics is still found because of standing waves due to reflected waves from antenna ends. The limitation overcome by a distribution of resistive loads near ends of wire. The antenna loaded resistively has flat characteristics satisfying a power gain of $6.5\pm1.1$dBi and VSWR of at most 2 over 10:1 bandwidth. The results are verified by comparing with similar results for the conventional linear V-dipole.

• Journal of Satellite, Information and Communications
• /
• v.6 no.1
• /
• pp.57-62
• /
• 2011

The VLC (visible light communication) system is communication technology using visible rays (RGB) that come out in LED device. It is energy curtailment effect and possible in ubiquitous network service applications. Also, VLC system has the above advantage about that the communication throughout the whole room is enabled by high power lighting and lighting equipment with white colored LED which are easy to install and have good outward appearance. However, the signal detection performance for the receiver near the network of transmitter boundary is severely degraded and the transmission efficiency decreased due to the influence of the interference signal from the adjacent networks. In this paper, we propose an interference mitigation method with optical beamforming in VLC systems, and evaluate the reception performance. For the system BER, the proposed optical beamforming transmission demonstrates the performance enhancement compared to the not using the optical beamforming scheme, and up to about 5~6dB SNR performance gain is achieved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1113-1120
• /
• 2014

In this paper, general methods for enhancing the transmission efficiency through the small subwavelength aperture in an infinite conducting plane are considered first by use of the transmission-resonant aperture like the ridged circular aperture structure, second by employing the transmission-resonant cavity structure. In particular, the maximum transmission cross section is found to be $\frac{2G{\lambda}^2}{4{\pi}}[m^2]$ for the two structures, where G is the gain of the aperture in the output half space. As experimental works, the impedance matching characteristics are investigated for the cases that above two structures are incorporated as a potential near field microscopic probe in the waveguide end. As a complementary problem to the above transmission-resonant aperture problem, some discussions are also given on the scattering resonance by the scattering object much smaller than the wavelength. This discussion may provide a good understanding of the physics for the phenomena that the maximum scattering cross section is much larger than the physical size of the atom in atomic physics area.