• FLOWER RESEARCH JOURNAL
• /
• v.18 no.3
• /
• pp.186-192
• /
• 2010

An infrared heating system, installed in a small venlo-type glasshouse ($280m^2$) in Gyeongsang National University, Jinju, Korea, was used to investigate its heating effect with potted Phalaenopsis, Schefflera arboricola 'Hongkong', Ficus elastica 'Variegata', and Rosa hybrida 'Yellow King' as the test plants. Temperature changes in test plants with the system turned 'On' and 'Off' were measured by using an infrared camera and the consumption of electricity by this infrared heating system was measured and analyzed. In potted Phalaenopsis, when the set air temperature of the greenhouse was $18^{\circ}C$, temperature of leaves and the growing medium were $22.8{\sim}27^{\circ}C$ and $21.3{\sim}24.3^{\circ}C$, respectively. In such tall plants as Schefflera arboricola 'Hongkong' and Ficus elastica 'Variegata', the upper part showed the highest temperature of 24.0 and $26.9^{\circ}C$, respectively. From the results of temperature change measurements, the plant temperatures were near or above the set point temperatures with some fluctuations depending on the position or distance from the infrared heating system. When air temperature between night and dawn dropped sharply, plant temperatures were maintained close to the set temperature ($18^{\circ}C$). There was a significant difference between 'On' and 'Off' states of the infrared heating system in average temperatures of root zone and leaf: 21.8 and $17.8^{\circ}C$ with the system 'On' and 20.4 and $15.5^{\circ}C$ with the system 'Off', respectively, in a cut rose Rosa hybrida 'Yellow King'. The heating load was about $24,850{\sim}35,830kcal{\cdot}h^{-1}$, which comes to about 27,000~40,000 won in Korean currency when calculated in terms of the cost of heating by a hot water heating system heated by petroleum. The cost for heating by the infrared heating system was about 35% of that of a hot water heating system. With the infrared heating system, the air temperature during the night was maintained slightly lower than the set point air temperature, probably due to the lack of air tightness of the glasshouse. Therefore, glasshouses with an infrared heating system requires further investigation including the installation space of the heat-emitting units, temperature sensor positions, and convection.

• The Korean Journal of Vision Science
• /
• v.20 no.4
• /
• pp.579-588
• /
• 2018

Purpose : To analyze the eyeglasses supply system for ametropic soldiers in ROK military. Methods : We investigated and analyzed the supply system of eyeglasses for the ametropic soldiers provided by the Korean military. The refractive powers and corrected visual acuity were measured for 37 ametropic soldiers who wear insert glasses for ballistic protective and gas-masks supplied by the military based on their habitual prescriptions. Full correction of refractive error was prescribed for subjects having less than 1.0 of distance visual acuity, and comparison was held for inspecting the changes in corrected visual acuity. Suggestions were provided for solving the issues regarding current supplying system, and this study investigated the applicabilities for utilizing professional optometric manpower. Results : The new glasses supplied by army for ametropic soldiers were duplicated from the glasses they worn when entering the army. The spherical equivalent refractive powers of the conventional, ballistic protective and gas-mask insert glasses supplied for 37 ametropic soldiers were $-3.47{\pm}1.69D$, $-3.52{\pm}1.66D$ and $-3.55{\pm}1.63D$, respectively, and the spherical equivalent refractive power of full corrected glasses was $-3.79{\pm}1.66D$, which showed a significant difference(p<0.05). The distant corrected visual acuity measured at high and low contrast(logMAR) of conventional, ballistic protective and gas-mask insert glasses were $0.06{\pm}0.80$, $0.21{\pm}0.82$, $0.15{\pm}0.74$, $0.34{\pm}0.89$, $0.10{\pm}0.70$ and $0.22{\pm}0.27$, respectively, while the corrected visual acuity by full corrected glasses were increased to $0.02{\pm}1.05$, $0.10{\pm}0.07$, $0.09{\pm}0.92$, $0.26{\pm}0.10$, $0.04{\pm}1.00$ and $0.19{\pm}1.00$, respectively. There was a significant difference(p<0.05) except for the case of the low contrast corrected visual acuity of the conventional and gas-mask insert glasses. The procedure for ordering, dispensing, and supplying military glasses consists of 5 steps, and it was found that approximately two weeks or more are required to supply from the initial examination. Conclusion : The procedure of supplying the military glasses showed three issues: 1) a lack of refraction for prescription system, 2) relatively long length of time required for supplying the glasses, 3) an inaccurate power of supplied glasses. In order to solve those issues, in the short term, education is necessarily required for soldiers on the measurement of the refractive powers, and in the near future, further standard procedures for prescription of glasses as well as the securement of optometric manpower are expected.

• Korean Journal of Heritage: History & Science
• /
• v.45 no.4
• /
• pp.54-73
• /
• 2012

In this article, we examined the patterns of activities of the Sarmathians though in a humble measure, with a focus on the regions where the Sarmathian sheaths spreaded. One of the main weapons the mounted nomads like the Scythias, the Sarmathians, and the Alans used at war was a spear. Though complementary, a sword was the most convenient and appropriate weapon when fighting at a near distance, fallen from the horse to the ground. The Sarmathian swords continued the tradition of the Akinakes which the Scythias or the Persians used, but those of the Sarmathians showed some advances in terms of the easiness with which a sword was drawn out from a sheath, and the way the sheaths were worn to parts of a human body. It turns out that the Sarmathian sheaths, which were designed for the people to draw swords easily, having the sheaths attached to thighs through 4 bumps, spread extensively from Pazyryk, Altai, to South Siberia, Bactria, Parthia and Rome. The most noteworthy out of all the Sarmathian sheaths were the ones that were excavated from the 4th tomb in Tillatepe, Afghanistan which belonged to the region of Bactria. The owner of the fourth tomb of Tilla-tepe whose region was under the control of Kushan Dynasty at that time, was buried wearing Sarmathian swords, and regarded as a big shot in the region of Bactria which was also under the governance of Kushan Dynasty. The fact that the owner of the tomb wore two swords suggests that there had been active exchange between Bactria and Sarmathia. It seemed that the reason why the Sarmathians could play an important role in the exchange between the East and the West might have something to do with their role of supplying Chinese goods to Silk Road. That's why we are interested in how the copper mirrors of Han Dynasty, decoration beads like melon-type beads, crystal beads and goldring articulated beads, and the artifacts of South China which produced silks were excavated in the northern steppe route where the Sarmathians actively worked. Our study have established that the eye beads discovered in Sarmathian tomb estimated to have been built around the 1st century B.C. were reprocessed in China, and then imported to Sarmathia again. We should note the Huns as a medium between the Sarmathians and the South China which were far apart from each other. Thus gold-ring articulated beads which were spread out mainly across the South China has been discovered in the Huns' remains. On the other hand, between 2nd century B.C. and 2nd century A.D. which were main periods of the Sarmathians, it was considered that the traffic route connecting the steppe route and the South China might be West-South silk road which started from Yunnan, passed through Myanmar, Pakistan, and Afghanistan, and then went into the east of India. The West-south Silk road is presumed to have been used by nomadic tribes who wanted to get the goods from South China before the Oasis route was activated by the Han Dynasty's policy of managing the countries bordering on Western China.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.3
• /
• pp.178-199
• /
• 2011

The ancient tombs found in Bokcheon-dong, Busan originate from the time between the $4^{th}$ and $5^{th}$ centuries, the period of the Three Nations. They are known as the tombs where the Vertical Plate Armour was mainly buried. In 2006, two units of the Vertical Plate Armour were additionally investigated in the tombs No.164 and No.165 which had been constructed at the end of the eastern slope near the hill of the group of ancient tombs in Bokcheon-dong. Throughout this study, the contents of the two units of the Vertical Plate Armour, whose preservation process has been completed, have been arranged, while the group of constructed ancient tombs in Bokcheon-dong from the $4^{th}$ century has been observed through the consideration of the burial pattern. The units of the Vertical Plate Armour from the tombs No.164 and No.165 can be classified as the IIa-typed armor showing the Gyeongju and Ulsan patterns, according to the attribute of the manufacturing technology. Also, they can be chronologically recorded as those from the early period of Stage II among the three stages regarding the chronological recording of the Vertical Plate Armour. While more than two units of the Vertical Plate Armour were buried in the largesized tomb on the top of the hill of the group of ancient tombs, one unit of the Vertical Plate Armour was buried in the small-sized tomb. By considering such a trend, it can be said that in the stage of burying the armor showing the Gyeongju and Ulsan patterns (I-type and IIa-type), different units of the Vertical Plate Armour were buried according to the size of the tomb. However, as the armor showing the Busan pattern (IIb-type) was settled, only one unit was buried. Meanwhile, the tombs No.164 and No.165 can be included in the wooden chamber tomb showing the Gyeongju pattern, which is a slender rectangular wooden chamber tomb with the aspect ratio of more than 1:3. However, according to the trend shown by the buried earthenware, it can be said that there seem to be common types and patterns shared with the earthenware which has been found in the area of Gimhae and is called the one showing the Geumgwan Gaya pattern. In other words, there seem to be close relationships between the subject tombs and the tomb No.3 in Gujeong-dong and the tomb No.55 in Sara-ri, Gyeongju, regarding the types of armor and tombs and the arrangement of buried artifacts. However, the buried earthenware shows a relationship with the areas of Busan and Gimhae. By considering the combined trend of the Gyeongju and Gimhae elements found in one tomb, it is possible to assume that the group of constructed ancient tombs in Bokcheon-dong used to be actively related with both areas. It has been thought that the Vertical Plate Armour used to be the exclusive property of the upper hierarchy until now, since it was buried in the large-sized tomb located on the top of the hill of the group of ancient tombs in Bokcheondong. However, as shown in case of the tombs No.164 and No.165, it has been verified that the Vertical Plate Armour was also buried in the small-sized tomb in terms of such factors as locations, sizes, the amount of buried artifacts and the qualitative aspect. Therefore, it is impossible to discuss the hierarchical characteristic of the tomb just based on the buried units of the Vertical Plate Armour. Also, it is difficult to assume that armor used to symbolize the domination of the military forces. The hierarchical characteristic of the group of constructed ancient tombs in Bokcheon-dong from the $4^{th}$ century can be verified according to the location and size of each tomb. As are sult, the re seem to be some differences regarding the buried units of the vertical plate armour. However, it would be necessary to carry out amore multilateral examination in order to find out whether the burial of the vertical plate armour could be regarded as the artifact which symbolizes the status or class of the deceased.

• Korean Journal of Heritage: History & Science
• /
• v.42 no.1
• /
• pp.88-99
• /
• 2009

This study was conducted to formulate management guidelines for Natural monumental old trees in Korea through survey of tree vigor and analysis of growing environments. A total of 20 old trees designated as natural monuments in Seoul, Incheon, and Gyeonggi Province were surveyed. The biological characteristics were surveyed with 4 items of species, ages and height of trees. The surrounding environments were surveyed with 2 items of location types and surroundings. The root conditions were surveyed with 2 items of denudation and molding depth. The health conditions were surveyed with 5 items of withering rate, cavity size, bark breakaway rate, damages by blight and insects, and growing tips. The soil conditions were surveyed with 6 items of PH, organic contents, valid phosphoric acid, transposal cations(K, Ca) and soil compaction. On the basis of outcomes of these research items, mutual relations among locations, growings and soil conditions of old trees were analyzed by carring out cross tabulation, correlation, and simple and multiple regression. Management guidelines were presented searching the factors effecting on the health of the monumental old trees. On the biological characteristics, the old trees designated as natural monuments were Pinus bungeana(4 trees), Juniperus chinensis(3 trees), Ginkgo biloba(3 trees), Poncirus trifoliata(2 trees). Actinidia arguta, Wisteria floribunda, Thuja orientalis, Quercus mongolica, Sophora japonica, Fraxinus rhynchophylla, Zelkova serrata, and Pinus densiflora. The tree height ranged from 4.2 to 39.2m, and root collar rounds ranged from 1.01 to 15.2m. On the surrounding environments, The location types ; Gardens(4), historical sites(5), residental sections(3) open agricultural fields(3), mountain hills(3), and near ocean beaches(1) and stream site(1). The surroundings ; 75% denudation of roots, molded more than 10cm except 4 trees(25%). On the health conditions, 1)Withering rate ; Ginkgo biloba(20%) in Yongmoon temple, (5%) in Saki-ri, kanwha-gun, and others had no withering rate. 2) Cavity size ; all subject had $5{\sim}100cm^3$ of cavity. 3) Bark breakaway rate ; Pinus bungeana in Soosong-dong, in the shrine of Confucius, in Samchung-dong, especially high rate of cavity(5~50%) in Seoul area and in Saki-ri, Kangwha-gun were high 45% brakeaway rate. 4) Damages by blight and insects was slight due to managements. 5Growing tips ; In cases of Juniperus chinensis in Changdeok palace and SunnogDang, seoul, growing tips were 1/2, presumably cause by air pollution, and in cases of Fraxinus rhynchophylla in Paju city and Pinus densiflora in BacksaDorip-ri, Icheon city, growing tips were fine, presumably because there were no moldings. On the Soil conditions, Soil pH ranged from 5.2 to 8.3, organic matter contents from 12% to 56%, phosphorus contents from 104 to 618ppm, soil compaction ranged from 7 to 28mm( among them, Denudation was severe with 21~28mm soil compactions in cases of Pinus bungeana in Soosong -dong, Thuja orientalis in Samchung -dong, Ginkgo biloba in the shrine of Confucius and in Yongmoon temple.) Results of cross tabulation, correlation, and regression analysis showed that molding depth was the most serious factor to deteriorate the tree vigor and cambium conductivity. In addition, soil acidity, organic matter contents, disease and insect damages and cambial detachment were also related to the tree vigor. Additional research of these relationships will be needed to conduct more detailed studies. Based on the relationships between the tree vigor and growing environments, it is considered that old trees should be managed to give them more growing spaces and less abuses. Also, molded soils should be removed and further soil-molding around the tree collar should be prohibited. For the construction of systematic management and removal of harmful factors, appropriative management according to spices, persistent monitering of damaged cases and construction of management system through the accumulation of data on the relationships of soil conditions are required.

• The Korean Journal of Air & Space Law and Policy
• /
• v.33 no.2
• /
• pp.35-59
• /
• 2018

Professor Bin Cheng said that outer space was res extra commercium, while the moon and the other celestial bodies were res nullius before the 1967 Outer Space Treaty(OST). However, Article 2 of the OST made the moon and other celestial bodies have the legal status as res extra commmercium, not appropriated by any country or private enterprises or individual person, but the resources there can be freely available, as those on the high seas. The non-appropriation principle was introduced to corpus juris spatialis internationalis. Whether or not the non-appropriation principle is binding for the non-parties of the OST, many scholars see this principle as an international customary law, even developing into jus cogens. Article 11(2) of the Moon Agreement(MA) reconfirms the nonappropriation principle of Article 2 of the OST, but it has much less effect than the OST because the MA binds only the 18 parties involved. The MA applies only to the moon and celestial bodies other than the Earth in the Solar System, the OST's application scope extends to the Galaxy because the OST has no such substantive enactment. As referred to in the 2015 CSLCA of USA or Luxembourg's Law of Space Resources, allowing individuals and enterprises run by other countries to commercially explore and utilize the space resources, the question may arise whether this violates the non-appropriation principle under Article 2 of the OST and Article 11 of the MA. In the case of the CSLCA, the law explicitly specifies that sovereignty, possessory rights, and judiciary rights to a specific celestial body cannot be claimed, let alone ownership. This author believes that this law respects the legal status of outer space and the celestial bodies as res extra commmercium. As long as any countries or private enterprises or individuals respect the non-appropriation principle of outer space and the celestial bodies, they could use, exploit it. Another question might be raised in the difference between res extra commercium on the high seas and res extra commercium in outer space and the celestial bodies. Collecting resources on the high seas and exploiting space resources should be interpreted differently. On the high seas, resources can be collected without any obstacles like fishing, whereas, in the case of the deep sea-bed area, the Common Heritage of Mankind principles under the UNCLOS should be operated by the International Seabed Authority as an international regime. The nature or form of the sea resources found on the high seas are thus different from that of space resources, which are fixed on the moon and the celestial bodies without water. Thus, if individuals or private enterprises collect these resources from outer space and the celestial bodies, they might secure a certain section and continue collecting or mining works without any limitation. If an American enterprise receives an approval from the U.S. government, secures the best location and collects resources on the moon, can other countries' enterprises access to this area? How large the exploiting place can be allotted on the moon? How long should such a exploiting activity be lasted? Under the current international space law, these matters might be handled according to the principle of "first come, first served." As a consequence, the international community should provide a guideline or a proposal for the settlement of any foreseeable disputes during the space activity to solve plausible space legal questions in the near future.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.5
• /
• pp.5-19
• /
• 2019

Considering the natural phenomenon in which steep slopes ($65^{\circ}{\sim}85^{\circ}$) consisting of rock mass remain stable for decades, slopes steeper than 1:0.5 (the standard of slope angle for blast rock) may be applied in geotechnical conditions which are similar to those above at the design and initial construction stages. In the process of analysing the stability of a good to fair continuum rock slope that can be designed as a steep slope, a general method of estimating rock mass strength properties from design practice perspective was required. Practical and genealized engineering methods of determining the properties of a rock mass are important for a good continuum rock slope that can be designed as a steep slope. The Genealized Hoek-Brown (H-B) failure criterion and GSI (Geological Strength Index), which were revised and supplemented by Hoek et al. (2002), were assessed as rock mass characterization systems fully taking into account the effects of discontinuities, and were widely utilized as a method for calculating equivalent Mohr-Coulomb shear strength (balancing the areas) according to stress changes. The concept of calculating equivalent M-C shear strength according to the change of confining stress range was proposed, and on a slope, the equivalent shear strength changes sensitively with changes in the maximum confining stress (${{\sigma}^{\prime}}_{3max}$ or normal stress), making it difficult to use it in practical design. In this study, the method of estimating the strength properties (an iso-angle division method) that can be applied universally within the maximum confining stress range for a good to fair continuum rock mass slope is proposed by applying the H-B failure criterion. In order to assess the validity and applicability of the proposed method of estimating the shear strength (A), the rock slope, which is a study object, was selected as the type of rock (igneous, metamorphic, sedimentary) on the steep slope near the existing working design site. It is compared and analyzed with the equivalent M-C shear strength (balancing the areas) proposed by Hoek. The equivalent M-C shear strength of the balancing the areas method and iso-angle division method was estimated using the RocLab program (geotechnical properties calculation software based on the H-B failure criterion (2002)) by using the basic data of the laboratory rock triaxial compression test at the existing working design site and the face mapping of discontinuities on the rock slope of study area. The calculated equivalent M-C shear strength of the balancing the areas method was interlinked to show very large or small cohesion and internal friction angles (generally, greater than $45^{\circ}$). The equivalent M-C shear strength of the iso-angle division is in-between the equivalent M-C shear properties of the balancing the areas, and the internal friction angles show a range of $30^{\circ}$ to $42^{\circ}$. We compared and analyzed the shear strength (A) of the iso-angle division method at the study area with the shear strength (B) of the existing working design site with similar or the same grade RMR each other. The application of the proposed iso-angle division method was indirectly evaluated through the results of the stability analysis (limit equilibrium analysis and finite element analysis) applied with these the strength properties. The difference between A and B of the shear strength is about 10%. LEM results (in wet condition) showed that Fs (A) = 14.08~58.22 (average 32.9) and Fs (B) = 18.39~60.04 (average 32.2), which were similar in accordance with the same rock types. As a result of FEM, displacement (A) = 0.13~0.65 mm (average 0.27 mm) and displacement (B) = 0.14~1.07 mm (average 0.37 mm). Using the GSI and Hoek-Brown failure criterion, the significant result could be identified in the application evaluation. Therefore, the strength properties of rock mass estimated by the iso-angle division method could be applied with practical shear strength.

• Korean Journal of Mineralogy and Petrology
• /
• v.34 no.1
• /
• pp.41-56
• /
• 2021

The characteristics of the six rock cleavages(R1~H2) in Jurassic Hapcheon granite were analyzed using the distribution of ① microcrack lengths(N=230), ② microcrack spacings(N=150) and ③ Brazilian tensile strengths(N=30). The 18 cumulative graphs for these three factors measured in the directions parallel to the six rock cleavages were mutually contrasted. The main results of the analysis are summarized as follows. First, the frequency ratio(%) of Brazilian tensile strength values(kg/㎠) divided into nine class intervals increases in the order of 60~70(3.3) < 140~150(6.7) < 100~110·110~120(10.0) < 90~100(13.3) < 80~90(16.7) < 120~130·130~140(20.0). The distribution curve of strength according to the frequency of each class interval shows a bimodal distribution. Second, the graphs for the length, spacing and tensile strength were arranged in the order of H2 < H1 < G2 < G1 < R2 < R1. Exponent difference(λS-λL, Δλ) between the two graphs for the spacing and length increases in the order of H2(-1.59) < H1(-0.02) < G2(0.25) < G1(0.63) < R2(1.59) < R1(1.96)(2 < 1). From the related chart, the six graphs for the tensile strength move gradually to the left direction with the increase of the above exponent difference. The negative slope(a) of the graphs for the tensile strength, suggesting a degree of uniformity of the texture, increases in the order of H((H1+H2)/2, 0.116) < G((G1+G2)/2, 0.125) < R((R1+R2)/2, 0.191). Third, the order of arrangement between the two graphs for the two directions that make up each rock cleavage(R1·R2(R), G1·G2(G), H1·H2(H)) were compared. The order of arrangement of the two graphs for the length and spacing is reverse order with each other. The two graphs for the spacing and tensile strength is mutually consistent in the order of arrangement. The exponent differences(ΔλL and ΔλS) for the length and spacing increase in the order of rift(R, -0.08) < grain(G, 0.14) < hardway(H, 0.75) and hardway(H, 0.16) < grain(G, 0.23) < rift(R, 0.45), respectively. Fourth, the general chart for the six graphs showing the distribution characteristics of the microcrack lengths, microcrack spacings and Brazilian tensile strengths were made. According to the range of length, the six graphs show orders of G2 < H2 < H1 < R2 < G1 < R1(< 7 mm) and G2 < H1 < H2 < R2 < G1 < R1(≦2.38 mm). The six graphs for the spacing intersect each other by forming a bottleneck near the point corresponding to the cumulative frequency of 12 and the spacing of 0.53 mm. Fifth, the six values of each parameter representing the six rock cleavages were arranged in the order of increasing and decreasing. Among the 8 parameters related to the length, the total length(Lt) and the graph(≦2.38 mm) are mutually congruent in order of arrangement. Among the 7 parameters related to the spacing, the frequency of spacing(N), the mean spacing(Sm) and the graph (≦5 mm) are mutually consistent in order of arrangement. In terms of order of arrangement, the values of the above three parameters for the spacing are consistent with the maximum tensile strengths belonging to group E. As shown in Table 8, the order of arrangement of these parameter values is useful for prior recognition of the six rock cleavages and the three quarrying planes.

• Journal of Food Hygiene and Safety
• /
• v.37 no.2
• /
• pp.39-45
• /
• 2022

This study aimed to investigate the validation and modify the analytical method to determine quercetin-3-𝑜-gentiobioside and isoquercitrin in Abelmoschus esculentus L. Moench for the standardization of ingredients in development of functional health products. The analytical method was validated based on the ICH (International Conference for Harmonization) guidelines to verify the reliability and validity there of on the specificity, linearity, accuracy, precision, detection limit and quantification limit. For the HPLC analysis method, the peak retention time of the index component of the standard solution and the peak retention time of the index component of A. esculentus L. Moench powder sample were consistent with the spectra thereof, confirming the specificity. The calibration curves of quercetin-3-𝑜-gentiobioside and isoquercitrin showed a linearity with a near-one correlation coefficient (0.9999 and 0.9999), indicating the high suitability thereof for the analysis. A. esculentus L. Moench powder sample of a known concentration were prepared with low, medium, and high concentrations of standard substances and were calculated for the precision and accuracy. The precision of quercetin-3-𝑜-gentiobioside and isoquercitrin was confirmed for intra-day and daily. As a result, the intra-day precision was found to be 0.50-1.48% and 0.77-2.87%, and the daily precision to be 0.07-3.37% and 0.58-1.37%, implying an excellent precision at level below 5%. As a result of accuracy measurement, the intra-day accuracy of quercetin-3-𝑜-gentiobioside and isoquercitrin was found to be 104.87-109.64% and the daily accuracy thereof was found to be 106.85-109.06%, reflecting high level of accuracy. The detection limits of quercetin-3-𝑜-gentiobioside and isoquercitrin were 0.24 ㎍/mL and 0.16 ㎍/mL, respectively, whereas the quantitation limits were 0.71 ㎍/mL and 0.49 ㎍/mL, confirming that detection was valid at the low concentrations as well. From the analysis, the established analytical method was proven to be excellent with high level of results from the verification on the specificity, linearity, precision, accuracy, detection limit and quantitation limit thereof. In addition, as a result of analyzing the content of A. esculentus L. Moench powder samples using a validated analytical method, quercetin-3-𝑜-gentiobioside was analyzed to contain 1.49±0.01 mg/dry weight g, while isoquercitrin contained 1.39±0.01 mg/dry weight g. The study was conducted to verify that the simultaneous analysis on quercetin-3-𝑜-gentiobioside and isoquercitrin, the indicators of A. esculentus L. Moench, is a scientifically reliable and suitable analytical method.