• 한국추진공학회지
• /
• 제14권5호
• /
• pp.51-56
• /
• 2010

고속회전 시험장치를 이용하여 V 형태의 회전식 연료 노즐의 오리피스 직경에 따른 분사특성을 파악하기 위한 연구를 수행하였다. 시험장치는 고속 회전장치, 연료공급장치, 아크릴 케이스로 구성하였다. 분무 오리피스의 직경과 회전속도를 변화시켜가며 분무실험을 수행하였다. 분무입자의 크기 및 속도 측정은 PDPA(Phase Doppler Particle Analyzer) 시스템을 사용하였고, Nd-Yag Laser를 이용하여 분무특성을 가시화하였다. 실험결과, 분무오리피스의 직경이 커질수록 분무입자의 크기가 작아졌으며, 분무입자 크기가 가장 작은 값을 보이는 분무오리피스의 한계 직경이 존재하였다. 오리피스의 직경이 이 한계직경 보다 클 경우 분무입자의 크기는 더 이상 감소하지 않았다. 이것은 분무 오리피스의 직경이 한계직경보다 커질 경우 오리피스 내의 액막이 균일하게 분포하지 않기 때문으로 판단된다.

• 한국재료학회지
• /
• 제5권7호
• /
• pp.781-785
• /
• 1995

K$_{6}$P$_4$ $O_{13}$ flux로부터 30$\times$40$\times$70㎣ 크기의 inclusion이 없는 KTP 단결성을 성장시켰다 성장된 KTP 결정의 SHG 출력 특성 측정 결과 위상정합각은 $\theta$=90$^{\circ}$, $\Phi$=23.3$^{\circ}$이었고, $\Phi$방향의 angular acceptance는 약 2$^{\circ}$이었다. KTP 결정내 굴절율 변화에 따른 위상정합각 편차는 최대 0.17$^{\circ}$까지 변하였다. 또한 Nd : YAG와 brewster plate를 채용한 내부공진형의 diode pumped SHG module에 KTP 결정을 삽입하여 20mW의 녹색 laser를 얻었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.258-263
• /
• 2010

고속회전 시험장치를 이용하여 V 형태의 회전식 연료 노즐의 오리피스 직경에 따른 분사특성을 파악하기 위한 연구를 수행하였다. 시험장치는 고속 회전장치, 연료공급장치, 아크릴 케이스로 구성하였다. 분무 오리피스의 직경과 회전속도를 변화시켜가며 분무실험을 수행하였다. 분무입자의 크기 및 속도 측정은 PDPA(Phase Doppler Particle Analyzer) 시스템을 사용하였고, Nd-Yag Laser를 이용하여 분무특성을 가시화하였다. 실험결과, 분무오리피스의 직경이 커질수록 분무입자의 크기가 작아졌으며, 분무 오리피스의 직경이 2.6mm인 경우 최적의 분무형태를 보였다. 그러나 오리피스의 직경이 이보다 클 경우 분무입자의 크기는 더 이상 감소하지 않았다. 이것은 분무오리피스가 최적의 직경보다 커질 경우 오리피스내의 액막이 균일하게 분포하지 않기 때문으로 판단된다.

• Journal of Oral Medicine and Pain
• /
• 제22권1호
• /
• pp.23-29
• /
• 1997

A 49 years old male patient was referred from the Department of Medicine, KNUH for the management of painful oral lesions. The patient had disability of food and drug intake due to multiple intraoral ulcers. Extraoral findings showed upper and lower lip swelling, crust formation on the lips. The lesions were diagnosed as Stevens-Johnson syndrome based on clinical and hematologic findings. The patient was treated with saline irrigation and pulsed Nd:YAG laser irradiation. After 5 daily treatment, the lesions decreased in size and severity, and the patient became more comfortable for food intake and speeching. It was suggested from the results of this clinical trial that a pulsed Nd:YAG laser therapy would be helpful for the symptoms associated with Stevens-Johnson syndrome.

• 열처리공학회지
• /
• 제14권3호
• /
• pp.145-150
• /
• 2001

The effect of laser welding and surface treatment, developed as a method of repairing steam generator tubes, on the pitting corrosion resistance of alloy 690 was examined. The surfaces of some heat-treated Alloy 690 materials were melt-treated using the Nd-YAG laser beam, and then examined to characterize the microstructures. The resistance to pitting corrosion was evaluated by measuring of Ep(pitting potential) through the electrochemical tests and also by measuring the degree of pit generation through the immersion tests. The pit formation characteristics were investigated by observing microstructural changes and pit morphologies. The results show that the resistance to pitting corrosion increases in the order of the following list; solution annealed Alloy 690, thermally treated Alloy 690, and laser surface melt-treated Alloy 690. The melted region was found to have a cellular structure and fine precipitates. It was confirmed that the resistance of Alloy 690 to pit initiation and also to pit propagation was higher when it was laser treated than treated otherwise.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.143-146
• /
• 2009

One of the most important issues of crystalline silicon solar cell is minimizing reflectance at the surface. Laser texturing is an isotropic process that will sculpt the surface of a silicon wafer, regardless of its crystallographic orientation. We investigated surface texturing process using Nd-YAG laser ($\lambda$=1064 nm) on multi-crystalline silicon wafer. Removal of slag formed after the laser process was performed using acid solution (HF : $HNO_3$ : $CH_3COOH$ : DI water). The reflectance and carrier lifetime of the samples were measured and analyzed using UV-Vis spectrophotometer and carrier lifetime tester. It was found that the minimum reflectance of the samples was 16.39% and maximum carrier life time was $21.8\;{\mu}s$.

• 분석과학
• /
• 제33권2호
• /
• pp.86-97
• /
• 2020

Reconstruction and separation of explosive-contaminated overlapping fingerprints constitutes an analytical challenge of high significance in forensic sciences. Laser-induced breakdown spectroscopy (LIBS) allows real-time chemical mapping by detecting the light emissions from laser-induced plasma and can offer powerful means of fingerprint classification based on the chemical components of the sample. During recent years LIBS has been studied one of the spectroscopic techniques with larger capability for forensic sciences. However, despite of the great sensitivity, LIBS suffers from a limited detection due to difficulties in reconstruction of overlapping fingerprints. Here, the authors propose a simple, yet effective, method of using chemical mapping to separate and reconstruct the explosive-contaminated, overlapping fingerprints. A Q-switched Nd:YAG laser system (1064 nm), which allows the laser beam diameter and the area of the ablated crater to be controlled, was used to analyze the chemical compositions of eight samples of explosive-contaminated fingerprints (featuring two sample explosive and four individuals) via the LIBS. Then, the chemical validations were further performed by applying the Raman spectroscopy. The results were subjected to principal component and partial least-squares multivariate analyses, and showed the classification of contaminated fingerprints at higher than 91% accuracy. Robustness and sensitivity tests indicate that the novel method used here is effective for separating and reconstructing the overlapping fingerprints with explosive trace.

• Nuclear Engineering and Technology
• /
• 제49권4호
• /
• pp.865-872
• /
• 2017

For more than 10 years, the laser process has been studied for dismantling work; however, relatively few research works have addressed the effect of high-power fiber laser cutting for thick sections. Since in the nuclear sector, a significant quantity of thick material is required to be cut, this study aims to improve the reliability of laser cutting for such work and indicates guidelines to optimize the cutting procedure, in particular, nozzle combinations (standoff distance and focus position), to minimize waste material. The results obtained show the performance levels that can be reached with 10 kW fiber lasers, using which it is possible to obtain narrower kerfs than those found in published results obtained with other lasers. Nonetheless, fiber lasers appear to show the same effects as those of $CO_2$ and ND:YAG lasers. Thus, the main factor that affects the kerf width is the focal position, which means that minimum laser spot diameters are advised for smaller kerf widths.

• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.316-321
• /
• 2009

Co nanoparticles on silica substrates were fabricated by inducing a thin-film dewetting through two different processes-furnace annealing and pulsed-laser annealing. The effects of annealing temperature, film thickness and laser energy density on dewetting morphology and mechanism were investigated. Co thinfilms with thicknesses between 3 to 15 nm were deposited using ion-beam sputtering, and then, in order to induce dewetting, thermally annealed in furnace at temperatures between 600 and $900^{\circ}C$. Some as-deposited films were irradiated using a Nd-YAG pulsed-laser of 266 nm wavelength to induce dewetting in liquid-state. Films annealed in furnace agglomerated to form nanoparticles above $700^{\circ}C$, and those average particle size and spacing were increased with an increase of film thickness. On the laser annealing process, above the energy density of $100mJ/cm^2$, metal films were completely dewetted and the agglomerated particles exhibited greater size uniformity than those on the furnace annealing process. A detailed dewetting mechanism underlaying both processes were discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1312-1316
• /
• 2007

Strip casted and rolled magnesium sheet is become exiting material for car manufacturer, due to its better formability and specific strength compare with conventional extruded sheet. TWB technology was attractive for car body designer, because it saves the weight of the car without strength loss. In this study, the laser welding performance of magnesium sheet was investigated for Mg TWB panel manufacturing. The material was strip casted and rolled magnesium alloy sheet contains 3 wt% Al and 1 wt% Zn (AZ31). Lamp pumped Nd:YAG laser of 2kW was used and its laser light was delivered by optical fiber of 0.6mm core diameter to material surface with focusing optics of 200mm focal length for TWB welding. The microstructure of weld bead was investigated to check internal defects such as inclusion, porosity and cracks. Also mechanical properties and formability were evaluated for press forming of car body. For the results, there was no crack but inclusion or porosity on weld at some conditions.The tensile strength of weld was over 95% of base metal. Inner and outer panel of engine hood were press formed and assembled at elevated temperature.