• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.193-197
• /
• 2008

Array of micro-dimple on polyoxymethylene (POM) surface was fabricated using Q-switched Nd:YAG laser and its characteristics were studied in terms of heat affected zone (HAZ), dimple geometry, and the effect of specimen surface roughness. Process parameters such as lamp current, process time, and the stream of air in order to minimize HAZ and flow of molten polymer into cavity were extensively studied in this work. Dimple geometry was further investigated by 3-D optical microscopy to provide deep insight into morphological analysis near the dimples. This paper also presents the applicapability of micro-dimples in polymeric tribological system, such as a thrust bearing. Micro-dimples were expected to provide low coefficient of friction and enhanced lubricity at the sliding interface.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.322-324
• /
• 2007

Nd:YAG laser welding of AZ31B-H24 magnesium alloy was carried out using AZ61 filler wire(Mg-6wt%Al-1wt%Zn). Microstructure and mechanical properties of welded joint were examined by optical microscopy, scanning electronic microscopy(SEM), energy dispersive spectroscopy(EDS), electron probe micro analyzer(EPMA) and victors hardness, tensile test at the room and elevated temperature. Test results indicate that the specimens welded with AZ61 filler wire have better tensile strength, elongation and victors hardness at room temperature than those of welded without filler wire. However tensile strength are similar but elongation are quite different at elevated temperature.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.363-365
• /
• 2007

Titanium and its alloys have excellent corrosion resistance, high strength to weight ratios and high temperature creep properties, which make them using many various fields of application. Responding to these needs, welding processes for titanium are also being used including TIG, MIG, resistance welding, plasma arc welding, diffusion welding, electron beam welding and laser welding. In this study, It is possible to get sound beads without humping bead and spatter with the decrease of peak power according to increase of pulse width and change of welding speed for heat input control at pulsed Nd:YAG laser welding of titanium plates for Lap welding.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.206-208
• /
• 2000

0.65 mol% MgO-doped LiNbO$_3$single crystals were grown by CZ method. The obtained single crystals were colorless and transparent. Noncritically phase-matched second harmonic generation (SHG) of 532-nm radiation from 1064-nm in MgO-doped LiNbO$_3$has been investigated by using pulsed Nd:YAG laser. The phase-matching temperature was room temperature. SHG conversion efficiencies were typically achieved higher than 50% at the phase-matching temperature with no photorefractive damage in the region of fundamental power density which was used in this experiment. The thermo-birefringence coefficient and the electro-birefringence coefficient of SHG were calculated from the temperature phase-matching profile with the electric field.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1120-1125
• /
• 2004

Welding characteristics of STS304 stainless steel and Inconel 600 using a continuous wave Nd:YAG laser are experimentally investigated. Alloy 600 being used in steam generator tubing of pressurized water reactor(PWR) exposed to some corrosion environment, stress corrosion cracking can occur on this material. Presented here are the results from a series of experiments in which dissimilar metal welds were made using the gas tungsten arc welding process with pure argon shielding gas. But It is well known that solidification cracking susceptibility of austenitic alloys depends on the solidification temperature range and amount/distribution of solute rich liquid that exists at the terminal stages of solidification. An experimental study was conducted to determine effects of welding parameters and to optimize those parameters that have the most influence on eliminating or reducing the extent welding zone formation at dissimilar metal welds.

• Journal of Periodontal and Implant Science
• /
• v.26 no.1
• /
• pp.276-292
• /
• 1996

The purpose of this study was to evaluate whether removal of gingival epithelium with pulsed Nd :YAG laser could inhibit the downgrowth of junctional epithelium after alloplastic material grafting in periodontal bone defect. The periodontal bone defects were created surgically on the palatal aspect of the upper right and left molar teeth in 30 rats and filled with resorbable calcium carbonate($Biocoral\;450^{(R)}$: Inoteb, France). The control sites(right molar area) was sutured. The test side (left molar area) received controlled deepithelization of the oral and sulcular epithelium with pulsed Nd:YAG laser($Sunrise\;Maste^{(R)}$: Sunrise Technologies, U.S.A.) under the mode of 1.75W, 15Hz, 116mJ/pulse and was sutured. The control and test sites were evaluated clinically and histologically, at 1, 3, 7, 14, and 28 days postoperation. Clinically, the gingiva showed normal color and shape at the 5th day in the control site and at the 10th day in the test sites. Histologically, the junctional epithelium was formed at the 7th day in the control sites and at the 14th day in the test sites, and the long JE attachment were observed at the 28th day in both sites. The attachment of connective tissue to root surface was observed initially at the 7th day in the control sites and at the 14th day in the test sites, and completed at the 28th day in both sites. In summary, these results showed that the removal of oral epithelium using pulsed Nd:YAG Laser could not prevent epithelial downgrowth after alloplastic material implantation in rat periodontal bone defect.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1759-1761
• /
• 1996

Md:YAG laser has been used in many applications such as micromachining, nonlinear optical experiments, holography, and rangefinding. These applications quite often require operation of the laser at the $TEM_{00}$ mode since this mode produces the smallest beam divergence, the highest power density, and, hence, the highest brightness. In this study, a pinhole is put between a rod and a half mirror to make the $TEM_{00}$ mode, and then we measured the intensity distribution of the output beam as reducing the diameter of the pinhole from 6mm to 1.5mm. As a result, the optimum size of the pinhole fixed in a resonator to make the $TEM_{00}$ mode was obtained, and we found out that the output beam of the pulsed Nd:YAG laser with a single elliptical cavity has a Gaussian distribution.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.115-120
• /
• 2003

We have developed laser micro-machining technology for fabrication of the micro thin-film inductors. After the thin layers of FM/M/FM films were coated to the silicon substrate by using the conventional sputtering method, the new laser machining was applied to the patterning process that used to be carried out by the semiconductor lithography procedure. A CW Nd:YAG laser operating in TEM$\sub$00/ mode was actively Q-switched to obtain the very short pulse of 200 ns. The laser micro-machining process with pulse energy and repetition rate have been optimized as 5 mJ/pulse and 5 kHz, respectively, to obtain the line resolution as fine as 20 $\mu\textrm{m}$.

• Restorative Dentistry and Endodontics
• /
• v.26 no.4
• /
• pp.307-315
• /
• 2001

The application of Nd:YAG laser and irrigants to the root surface can change its surface configurations. The purpose of this study was to investigate the effects of Nd:YAG laser and irrigants on the apical seal of obturated canals. In this study, 66 single rooted teeth were randomly assigned to 4 group of 14 teeth each. 8 teeth were served us positive and negative controls. The teeth were divided into 6 groups as follows. Group A: Nd:YAG laser, 5% NaOCl + Rc-prep Group B: Nd:YAG laser, Saline Group C: 5% NaOCl + Rc-prep Group D: Saline Group E: Positive control Group F: Negative control 66 teeth were instrumented using Maillefer ProFile$^{\circledR}$ (Orifice Shapers, .04 taper, .06 taper Dentsply, Switzerland). Two of each group were selected at random, and the canal wall surfaces were examined under a SEM. 12 teeth of each group were obturated using by lateral condensation technique. Specimens were immersed in india ink for 7days, decalcified by 10% nitric acid, dehydrated by 75. 80. 85, 90, 95 and 100% alcohol in order cleared by methyl salicylate and then measured of dye penetration with stereomicroscope($\times$15 magnification) and Image Pro plus. The data were analyzed statistically by one-way ANOVA test and Duncan's Multiple Range test. The results were as follows : 1. The mean leakage was 0.128$\pm$0.376 for group A, 0.237$\pm$0.325 for group B, 0.397$\pm$0.468 for group C, 0.586$\pm$0.402 for group D, and there were statistically significant differences between group A and group D, group B and group D. (p<0.05). 2. Group A had better sealing ability than Group C, but there was statistically no significant differences. (p>0.05). 3. Group B had better sealing ability than Group D and there was statistically significant difference. (p<0.05). 4 Group A had better sealing ability than Group B, but there was statistically no significant difference. (p>0.05). 5. Group C had better sealing ability than Group D, but there was statistically no significant difference. (p>0.05). 6. As a result of observation under SEM, Smear layers were removed in Group A, B. but Smear layers were partially removed and smear plugs were remained in Group C, Smear layers were not removed in Group D. To be specially, Melting of smear layer were showed in Group C. 7. These results suggests that the laser has a potential in reducing the apical microleakage of obturated canals.

• Tuberculosis and Respiratory Diseases
• /
• v.52 no.1
• /
• pp.54-61
• /
• 2002

Background: Tracheal stenosis is an urgent but uncommon disease. Therefore, primary care clinicians have limited clinical experience. Animal models of a tracheal stenosis can be used conveniently for the learning, teaching, and developing new diagnostic and therapeutic modalities for tracheal stenosis. Recently, a canine model of a tracheal stenosis was developed using a Nd-YAG laser. To describe the methods and results of developed animal model, we performed this study. Methods : Six Mongrel dogs were generally anesthetized and the anterior 180 degree of tracheal cartilage of the animal was photo-coagulated using a Nd-YAG laser. The animals were bronchoscopically evaluated every week for 4 weeks and a pathologic evaluation was also made. Results : Two weeks after the laser coagulation, the trachea began to stenose and the stenosis progressed through 4 weeks. All animals suffered from shortness of breath, wheezing, and weight loss in the 3 weeks after the laser treatment, and two died of respiratory failure just before the fourth week. The gross pathologic findings showed the loss of cartilage and a dense fibrosis, which resulted in a fibrous stricture of the trachea. Microscopy also showed that the fibrous granulation tissue replaced destroyed cartilage. Conclusion : The canine model can assist in the understanding and development of new diagnostic and therapeutic modalities for tracheal stenosis.