• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.57-67
• /
• 2007

Laser surface hardening technologies have been used to improve characteristics of wear and to enhance the fatigue resistance fur mold parts. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser surface hardening for the case of SKD61 steel. CW Nd:YAG laser is selected as the heat source. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with a uniform hardness. From the results of the experiments, it has been shown that the maximum average hardness is approximatly 780 Hv when the power, focal position and the travel of laser are 1,095 W, 0mm and 0.3 m/min, respectively. In samples treated with lower scanning speeds, some small carbide particles appear in the interdendritic regions. This region contains fine martensite and carbide in proportions which depend on the local thermal cycle.

• Journal of Welding and Joining
• /
• v.25 no.4
• /
• pp.49-57
• /
• 2007

The optimization of the cladding parameters was studied to maximize the deposition efficiency in the laser cladding using a low power pulsed Nd:YAG laser. STS304 stainless steel plate and Co alloy powder were used as a substrate and powder for cladding, respectively. The six cladding parameters were selected through preliminary experiments and their effects on the deposition efficiency were analyzed statistically. Experiments were designed and carried out using the Taguchi experimental method using a L18 orthogonal array. It was found from the results of analysis of variance(ANOVA) that the powder feed position and powder feed angle had the most significant effects on the deposition efficiency, but the powder feed rate and laser focal position had nearly no effects. The deposition efficiency could be maximized at 0mm of the powder feed position and 50o of the powder feed angle in the experimental range. From this experimental analysis, a new laser cladding head with 20o of the powder feed angle was designed and manufactured. With a new laser cladding head, the highest deposition efficiency of 12.2% could be obtained.

• Korean Journal of Optics and Photonics
• /
• v.11 no.6
• /
• pp.434-440
• /
• 2000

We fabricated a high power Nd:YAG laser pumped by a 1 kW diode laser with a Lambertian-type diffusive reflector. Maximum cw power of 500 W with a slope efficiency of 49%, which corresponds to an optical efficiency of 46.7%, was obtained from a short linear resonator when a 5 mm rod was used. The efficiencies decreased when a 6 mm rod was used, due to the poor quality of the absorption distribution in the rod. The measured beam quality factor of 70, which is slightly smaller than the value calculated from the measured thermal focal lengths, shows that the absorption distribution in the rod is fairly uniform. iform.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.2
• /
• pp.275-279
• /
• 2011

Sterilization of Escherichia coli (E. coli) is examined using a unique pulsed ultra-violet (UV) elliptical reactor based on Nd:YAG laser resonator, UV radiation from a pulsed xenon flashlamp. The light from the discharge has a broadband emission spectrum extending from the UV to the infrared region with a rich UV contained. Sterilization method by using the UV light is fast, environment-friendly and it does not cause secondary pollution. A Nd:YAG laser resonator having elliptical shape has advantage of concentrating the radiation of the UV light at two foci as the quart sleeve filled with E. coli. The primary objective of this research is to determine the important parameters such as pulse per second (pps), the applied voltage for sterilizing E. coli by using an UV elliptical reactor. From the experiment result, the sterilization effect of UV elliptical reactor is better than that of UV cylindrical reactor, and it can be 99.9% of sterilization at 800V regardless of the pps within 10 minutes.

• Journal of Oral Medicine and Pain
• /
• v.25 no.4
• /
• pp.403-411
• /
• 2000

The authors experienced a non-painful, elevated, dome-shaped lesion on lower lip in Korean male of 22-year-old and a non-painful, elevated, dome-shape lesion on left side of mouth floor in Korean female of 36-year-old. And diagnosed the lesions as a mucocele and a ranula respectively, based on the comprehensive evaluation of data obtained from history taking, clinical and radiologic examination and histopathological findings. In these cases, the authors removed mucocele and ranula using the pulsed Nd:YAG laser with advantage of good hemostatic effect, and so we could minimize improper tissue destruction during operation. The excisional wounds of lower lip and mouth floor had a good healing process without any symptom of pain and any signs of bleeding and infection.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.99-104
• /
• 2010

Magnesium and magnesium alloys, the lightest structural materials, have been received plenty of global attention recently. These alloys could be applied in various fields, especially the electronics industry, because of their excellent electromagnetic interference shielding. However, the welding technique of magnesium alloys has not been established. This study is related to the welding of AZ31B magnesium alloy by a short-pulsed a Nd:YAG laser. Two types of pulse waves, square pulse and variable pulse, were used to control weld defects. Results show that the crack and porosity, generated in the weld, had not been controlled by general square pulse. But through the application of variable pulse, the defects could be prevented and the good weld zone was obtained.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.06a
• /
• pp.165-167
• /
• 1998

Nd:YAG crystals were grown by Horizontal Bridgman method. The effects of sliding rate (growth rate) of Molydbenum container, growth atmosphere and concentration of Neodymium ions on crystal qualities were investigated. The size of the crystals grown was up to 150-200 mm in length, 70 mm in width and 25-35 mm in thickness. Crystals grown under the optimum conditions were violet, transparent and could not be observed any macroscopic defects. Under the polarizing microscopoc observations with crossed polar, striations, {211} facets and inclusions were detected. With the grown crystals, prototypes of laser rods for 1.06$\mu$m laser application were manufactured and then characterized. As a result, we can get high quality of Nd:YAG laser rods with <111> and <110> axis, 63 mm in length and6.3 mm in diameter.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.3
• /
• pp.7-10
• /
• 1976

To eliminate some difficulties encountered in the operation of $LiNbO_3$ crystal as a Q-switch for generating a single pulse Nd-YAG laser, the operational characteristics of the crystal, was investigated. Also a simple method for solving the difficulties was presented.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.35-41
• /
• 2006

Recently, as ultrasonic medical devices are gradually developed, many of those requires smaller and more precision coaxial cables in probe. So, the use of micro coaxial cable becomes an efficient solution for ultrasonic machine. However, there are many difficulties in stripping micro coaxial cable by traditional mechanical process. In this paper, we use the Nd-YAG laser for the efficient stripping of conduct wire of cable. We propose a new method to strip the shield wire of micro coaxial cable. Through some experiments, we found that there is a new possibility in the proposed method. Also, in order to enhance the performance, we propose a preprocess of the cable before stripping.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.373-375
• /
• 1997

In this study, we designed multiple mesh circuit consisting of 3-6 meshes and pulse superposition one consisting of a 3 mesh, and fabricated the electrical power supply and the single elliptical resonator. We developed the two pulse superposition technique forming the step pulse shapes of pulsed Nd:YAG laser with single shot multivibrator and 2 SCRs. Laser beam generated by multiple mesh circuit and superposition one respectively irradiated target surface to analyze process state of surface with spark and vapor. And it was obtained experimental results that all superposition meshes had common points which the best efficiency was obtained at delay time 0[${\mu}s$], followed by, no superposition and obtained at delay time 250[${\mu}s$].