• Transactions of the Society of Information Storage Systems
• /
• v.6 no.2
• /
• pp.52-56
• /
• 2010

In this paper, we investigate the polarization multiplexing for micro holographic storage. The proposed multiplexing method is performed by using crystal media that use photorefractive materials such as Fe-doped $LiNbO_3$. We discuss the feasibility of fast recording, high capacity and transfer rate for polarization multiplexing method. Finally, we experimentally verify the proposed method using polarization selectivity.

• Journal of the Korean Ceramic Society
• /
• v.34 no.8
• /
• pp.877-885
• /
• 1997

The dependence of strength, crack growth, fracture mode and degree of domain rearrangement of PZT ceramics on poling strength were studied. The PZT [(Pb0.94Sr0.06)(Zr0.46Ti0.54)O3+Nb(trace)] specimens were poled at 0, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0 kv/mm, and the strength of the specimens was measured by 3 point flexure system. The bending strength of the specimen decreased in different modes according to the bending directions; xz, zx and yz plane direction with x axis of the poling direction in Cartesian coordinate system. The strength differences between the directions increased as the poling strength increased. The fracture mode transferred to intergranular fracture mode from transgranular one as the poling strength increased. The mechanical breakdown occurred when the poling strength higher than 3 kV/mm was applied to the specimen. It was observed that the crack length increased in the normal direction to the poling direction, however, decreased in the parallel direction to the poling direction when the poled PZT specimen was indented by the Vickers indenter. However, the crack produced by indentation continuously was continuously increased little by little after indentation on the specimen. The domain rearrangement occurred as the poling strength increased and the domains were rearranged more effectively when the electric field was continuously increased little by little.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.2
• /
• pp.24-27
• /
• 2012

The superconducting coil system is one of the most important components in Korea Superconducting Tokamak Advanced Research (KSTAR), which has been operated since 2008. $Nb_3Sn$ and NbTi superconductors are being used for cable-in-conduit conductors (CICCs) of the KSTAR toroidal field (TF) and poloidal field (PF) coils. The CICCs are cooled by forced-flow supercritical helium about 4.5 K. The temperature, pressure and mass flow rate of the supercritical helium in the CICCs are interacting with each other during the operation of the coils. The complicate behaviors of the supercritical helium have an effect on the operation and the efficiency of the helium refrigeration system (HRS) by means of, for instance, pressure drop. The hydraulic characteristics of the supercritical helium have been monitored while the TF coils have stably achieved the full current of 35 kA. In other hands, the PF coils have been operated with various pulsed or bipolar mode, so the drastic changes happen in view of hydraulics. The heat load including AC loss on the coils has been analyzed according to the measurement. These activities are important to estimate the temperature margin in various PF operation conditions. In this paper, the latest hydraulic behaviors of PF coils during KSTAR operation are presented.

• Nuclear Engineering and Technology
• /
• v.50 no.3
• /
• pp.416-424
• /
• 2018

Microstructure of oxide formed on Zr-Nb-Sn tube sample was intensively examined by scanning transmission electron microscopy after exposure to simulated primary water chemistry conditions of various concentrations of Zn (0 or 30 ppb) and dissolved hydrogen ($H_2$) (30 or 50 cc/kg) for various durations without applying desirable heat flux. Microstructural analysis indicated that there was no noticeable change in the microstructure of the oxide corresponding to water chemistry changes within the test duration of 100 days (pretransition stage) and no significant difference in the overall thickness of the oxide layer. Equiaxed grains with nano-size pores along the grain boundaries and microcracks were dominant near the water/oxide interface, regardless of water chemistry conditions. As the metal/oxide interface was approached, the number of pores tended to decrease. However, there was no significant effect of $H_2$ concentration between 30 cc/kg and 50 cc/kg on the corrosion of the oxide after free immersion in water at $360^{\circ}C$. The adsorption of Zn on the cladding surface was observed by X-ray photoelectron spectroscopy and detected as ZnO on the outer oxide surface. From the perspective of $OH^-$ ion diffusion and porosity formation, the absence of noticeable effects was discussed further.

• Journal of Korean Institute of Industrial Engineers
• /
• v.27 no.3
• /
• pp.250-259
• /
• 2001

Given a tree structured network in which each node has its own demand and also stands for a candidate location of a potential facility, such as plant or warehouse, a capacitated facility location problem on the network (CFLPOT) is to decide capacitated facility locations so that the total demand occurred on the network can be satisfied from those facilities with the minimum cost. In this paper, we first introduce a mixed integer programming formulation for CFLPOT with two additional assumptions, the indivisible demand assumption and the contiguity assumption and then show that it can be reformulated as a tree partitioning problem with an exponential number of variables. We then show that it can be solved in O($n^2b$) time by utilizing the limited column generation method developed by Shaw (1993), where n is the total number of nodes in the network and b is the maximum facility capacity. We also develop a depth-first dynamic programming algorithm with a running time of O(nb) for finding the locally maximal reduced cost which plays an important role in the limited column generation method. Finally, we implement our algorithms on a set of randomly generated problems and report the computational results.

• Journal of the Korean Ceramic Society
• /
• v.33 no.6
• /
• pp.665-671
• /
• 1996

Ferroelectric Pb(Fe1/2Nb1/2)O3 thin films were successfully fabricated on ITO/Glass substrate by sol-gel proces-sing and characterized to determine the dielectric and electric properties. Viscosity of PEN sol measured to investigate rheological properties was 3.25 cP which was proper for coating. The sol also showed Newtonian behavior. RTA(Rapid Thermal Annealing) was used for the annealing of the thin film and 1200~1700$\AA$ thick PEN thin films were fabricated by repeating the intermediate and the final annealing. After the deposition of Pt as top electrode by vacuum evaporation dielectric and electric properties were measured. Dielectric properties of FFN thin film were enhanced by increasing the perovskite phase fraction with increasing the annealing temperature. Measured dielectric constant of 1700$\AA$ PFN thin film annealed at $650^{\circ}C$ was 890 at 1kHz Capacitatnce density and dielectric loss were 47 fF/${\mu}{\textrm}{m}$2 and 0.47 respectively. As a result of measuring Curie temperature PFN thin films had Curie point with a rang of 110~12$0^{\circ}C$ and showed broad dielectric peak at that point. Leakage current of the PFN thin films were increased with increasing the annealing tempera-ture.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.10
• /
• pp.1069-1074
• /
• 2014

In this study, the piezoelectric characteristics of a piezoelectric paint sensor were investigated in relation to the poling time. This piezoelectric paint sensor was composed of PNN-PZT powder and epoxy resin with a 1:1 weight ratio. The dimensions of the paint specimen were $40{\times}10{\times}1mm^3$, and the top and bottom sides were both coated with a silver paste to create electrodes. During the poling treatment, the poling time was controlled to examine the effect of the piezoelectric properties, while the poling temperature was fixed at room temperature and the electric field was set to 4 kV/mm. The piezoelectric properties were measured by comparing the output voltage from the paint sensor to the force signal from an impact hammer when the impact hammer hit the specimen. In conclusion, the optimal poling conditions were found to be an electric field of 4 kV/mm and a poling time of around 30 min at room temperature.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.279-282
• /
• 2003

In this paper, to apply piezoelectric transformer for PDA backlight inverter, piezoelectric transformer using the composition which $Nb_2O_5$ added into PNW-PMN-PZT ceramics was fabricated as Rosen-type one with the size of $1165mm^3$. And their electrical characteristics were investigated with the variations of load resistance and driving frequency And then, the driving circuit for PDA CCFL(0.6W) which composed of the two MOSFETs connecting in series was manufactured using piezoelectric transformer, VCO and one-chip microprocessor. After driving for 25 min using the proposed circuit for PDA CCFL(0.6W), driving frequency of 214.4kHz, input voltage of 31.78 V and input current of 21.1mA were shown. And then, output voltage of 293.2 V and output current of 2.2mA were shown. At the same time, efficiency of 96.2$\%$ and temperature rise of $3.6^{\circ}C$ were appeared at the piezoelectric transformer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.418-425
• /
• 2019

A piezoelectric ceramic fiber composite (PCFC) was successfully fabricated using $0.69Pb(Zr_{0.47}Ti_{0.53})O_3-0.31[Pb(Zn_{0.4}Ni_{0.6})_{1/3}Nb_{2/3}]O_3$ (PZT-PZNN) for use in small-scale wind energy harvesters. The PCFC was formed using an epoxy matrix material and an array of Ag/Pd-coated PZT-PZNN piezo-ceramic fibers sandwiched by Cu interdigitated electrode patterned polyethylene terephthalate film. The energy harvesting performance was evaluated in a custom-made wind tunnel while varying the wind speed and resistive load with two types of flutter wind energy harvesters. One had a five-PCFC array vertically clamped with a supporting acrylic rod while the other used the same structure but with a five-PCFC cantilever array. Stainless steel (thickness: $50{\mu}m$) was attached onto one side of the PCFC to form the PZT-PZNN cantilever. The output power, in general, increased with an increase in the wind speed from 2 m/s to 10 m/s for both energy harvesters. The highest output power of $15.1{\mu}W$ at $14k{\Omega}$ was obtained at a wind speed of 10 m/s for the flutter wind energy harvester with the PZT-PZNN cantilever array. The results presented here reveal the strong potential for wind energy harvester applications to supply sustainable power to various IoT micro-devices.

• Journal of the Optical Society of Korea
• /
• v.15 no.2
• /
• pp.182-186
• /
• 2011

A poling method using multiple negative voltage was introduced to fabricate periodically poled lithium niobate (PPLN) devices with quasi-phase matching (QPM) period of $12.9\;{\mu}m$ by utilizing an real-time visualization system. We also performed variation of the electric field during the poling. Two different conventionally used poling method, negative and positive single pulses, were used and the poling quality compared through microscopic images and far-field diffraction pattern analysis. Etched images on the +z and -z surfaces of PPLN showed that negative multiple pulse poling presented the highest periodicity in domain structures among the three methods. Duty ratio and its standard deviation were measured by analyzing far-field diffraction patterns. The newly introduced method of negative multiple pulse poling had duty ratio of 0.42 which was close to the ideal value of 0.50 and standard deviation of 0.020 that was about 3 times smaller than that of the other conventional methods.