• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.4
• /
• pp.286-296
• /
• 2016

Offshore CCS technology is to transport and inject $CO_2$ which is captured from the power plant into the saline aquifer or depleted oil-gas fields. The more accumulated injected $CO_2$, the higher reservoir pressure increases. The increment of reservoir pressure make a dramatic change of the operating conditions of transport and injection systems. Therefore, it is necessary to carefully analyze the effect of operating condition variations over the injection period in early design phase. The objective of this study is to simulate and analyze the $CO_2$ behavior in the transport and injection systems over the injection period. The storage reservoir is assumed to be gas field in the East Sea continental shelf. The whole systems were consisted of subsea pipeline, riser, topside and wellbore. Modeling and numerical analysis were carried out using OLGA 2014.1. During the 10 years injection period, the change of temperature, pressure and phase of $CO_2$ in subsea pipelines, riser, topside and wellbore were carefully analyzed. Finally, some design guidelines about compressor at inlet of subsea pipeline, heat exchanger on topside and wellhead control were proposed.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.1
• /
• pp.71-80
• /
• 1992

The Seakeeping committee of Korea Towing Tank Conference executed the cooperative experimental study on deck wetting phenomena using S-175 contatiner model ships. Two members, Korea Research Institute of Ships and Ocean Engineering(KRISO) and Hyundai Maritime Research Institute(HMRI) participated in the study. This study was initiated by the ITTC(International Towing Tank Conference) Seakeeping Committee as the cooperative study of the 19th ITTC aiming at the establishement of the model test procedure on the deck wetting phenomena. Special emphasis was made on the determination of reliable record length for experimental measurement on rarely occurring events(such as deck wetness, slamming etc). Comparisons were made on both the test results and the test procedrues in this research. The measured frequencies of deck wetting show remarkable deviations between the runs. This fart implies that sufficiently long record length is required in the deck wetness measurement compared to the conventional ship motion tests. Careful considerations were made on the physical interpretation of the deck wetting phenomena, the correlation between the measured relative motion at stemhead and the measured deck wetness, and the estimation of deck wetting frequencies by Poisson process.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.1
• /
• pp.45-53
• /
• 1985

For the analysis of vertical vibrations of a ship's hull, the Timoshenko beam analogy is accepted up to seven or eight-node modes provided that the system parameters are properly calculated. As to the shear coefficient, it has been a common practice to apply the strain energy method or the projected area method. The theoretical objection to the former is that it ignores lateral contraction due to Poisson's ratio, and the latter is of extreme simplifications. Recently, Cowper's and Stephen's shear coefficient formulas have drawn ship vibration analysts' attentions because these formulas, derivation of which are based on an integrations of the equations of three-dimensional elasticity, take Poisson's ratio into account. Providing computer programs for calculation of the shear coefficient of ship sections modeled as thin-walked multicell sections by each of the forementioned methods, the authors calculated natural vibration characteristics of a bulk carrier and of a container ship by the transfer matrix method using shear coefficients obtained by each of the methods, and discussed the results in comparision. The major conclusions resulted from this investigation are as follows: (1) The shear coefficients taking account of the effects of Poisson's ratio, Cowper's $K_c$ and Stephen's $K_s$, result in higher values of about 10% in maximum as compared with the shear coefficient $K_o$ based on the conventional strain energy methods; (a) $K_c/K_o{\cong}1.05\;and\;K_s/K_o{\cong}1.10$ for ships having single skin side-shell such as a bulk carrier. (b) $K_c/K_o{\cong}1.02\;and\;K_s/K_o{\cong}1.05$ for ships having longitudinally through bulkheads and/or double side-shells in the portion of the cargo hod such as a container carrier. (2) The distributions of the effective shear area along the ship's hull based on each of $K_o,\;K_c\;and\;K_s$ are similar each another except the both end portions. (3) Natural frequencies and mode shapes of the hull based on each of $K_c\;and\;K_s$ are of small differences as compared each other. (4) In cases of using $K_c\;or\;K_s$ in ship vibration analysis, it is also desirable to have the bending rigidity be corrected according to the effective breadth concept. And then, natural frequencies and mode shapes calculated with the bending rigidity corrected in the above and with each of $K_o,\;K_c\;and\;K_s$ result in small differences as compared each another. (5) Referring to those mentioned in the above (3) and (4) and to the full-scale experimental results reported by Asmussen et al.[17], and considering laboursome to prepare the computer input data, the following suggestions can safely be made; (a) Use of $K_o$ in ship vibration analysis is appropriate in practical senses. (b) Use of $K_c$ is appropriate even for detailed vibration analysis of a ship's hull. (6) The effective shear area based on the projected area method is acceptable for the two-node mode.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.1
• /
• pp.118-126
• /
• 2024

In this paper, the research contents and results related to the automation of the hull-form optimal design of container ships are summarized. A container ship is a ship that generally operates near Froude number of 0.26. To implement hull-form optimal design automation for ships operating at this speed, an optimization algorithm, a hull-form change algorithm, a ship performance prediction algorithm, an automation algorithm, and an iterative calculation technique were applied to develop a numerical analysis computer program that enables hull-form optimal design automation of the container ship, and it was named HOTCONTAINER. In this study, a sensitivity analysis algorithm was developed and applied to appropriately set design variables for hull-form optimal design. To understand the reliability and real ship applicability of the developed algorithm, a numerical analysis was performed on KCS(KRISO Container Ship), a container ship that has been studied in various ways worldwide. Consequently, the optimal ship was derived, and the wave resistance, wave pattern, and wave height of the target and optimal ship were compared. In conclusion, compared the target ship, the optimal ship a 47.63% decrease in wave resistance, and the displacement and wet surface area decreased by 0.50% and 0.39%, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.43 no.3
• /
• pp.222-231
• /
• 2007

This paper represents a basic statistical examination on the navigability of ocean-going ship from the point of estimating the time lasting period when propeller racing occurred by using the basic probability theory and the statistics. The propeller racing is one of the most important seakeeping qualities in relation to the safety of the main engine and shafting system. The trend of the racing has been mainly investigated in order to estimate allowable maximum propeller diameter, operation of ocean-going ships, etc.. In those studies, the propeller racing generally and mainly means the situation (propeller exposed) in which the relative motion amplitude between ship hull and wave surface would exceed a depth of point in rotary disk propeller. Therefore, it seems that the magnitude of the amplitude and its exceeding frequency of propeller racing have been examined as a principal subject of study as usual. However, the time during which the amplitude exceeds the depth of point, that is, the propeller exposes in the air, must be also one of most important factor affecting the trend of propeller racing. Then, this paper proposes a new practical method for estimating the time lasting of exposed propeller related to propeller racing in rough-confused seas on the basis of the linear strip theory and the statistics. And, numerical examples of estimating the propeller racing probability are given for four wide ship forms. Finally the usefulness of the proposed method for predicting propeller racing based on the time lasting period is discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.373-380
• /
• 2020

A valve product can be over-designed or too heavy. Finite element analysis was performed using ANSYS for two and three-dimensional ball valve models, and the ball weight was reduced by optimization within the allowable design criteria. The ball is structurally safe according to the computed stress values, which are within the material's admissible stress. The weight was reduced by about 22%, and the structural safety factor was 1.25. The structural safety of the seat insert and ring, which are used to prevent leakage, was confirmed through finite element analysis. It is shown that the two-dimensional analysis can result in similar values to the three-dimensional analysis for the axisymmetric structure. The redesign of the valve is not included in the results since such changes require a whole new design process, including all valve components.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.7 no.4
• /
• pp.174-179
• /
• 2004

Domestic marine diesel engine makers reduce the NOx emission mostly by applying low NOx fuel nozzle and injection timing retard. However, it is necessary to develop high efficient technology (EGR, DWI and SCR, etc.) to reduce NOx emission in order to prepare for the further reinforcement of the NOx emission limit. Also, in the near future, IMO will restrict additively THC, PM and CO with NOx. Therefore, domestic engine makers have to prepare for it and the relevant government ministries should give a sufficient support to these technology research and establish or amend the relevant law, which should include the excursion riverboat.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.7 no.4
• /
• pp.216-223
• /
• 2004

A nonlinear sloshing problem is numerically simulated. During excessive sloshing the sloshinginduced impact load can cause a critical damage on the tank structure. A three-dimensional free-surface flow in a tank is formulated in the scope of potential flow theory. The exact nonlinear free-surface condition is satisfied numerically. A finite-element method based on Hamiltons principle is employed as a numerical scheme. The problem is treated as an initial-value problem. The computations are made through an iterative method at each time step. The hydrodynamic loading on the pillar in the tank is computed.

• Journal of Advanced Navigation Technology
• /
• v.20 no.6
• /
• pp.519-527
• /
• 2016

The present study is concept research on the operation cost management of shipping firms, especially considering technology for economical ship operation of existing ships in units of voyage. The factors that influence economical ship operation management were identified by analyzing the current status of the shipping industry, the development of economical ship operation technologies, technological requirements, and the cost factors of ship operation. Economical operation of existing ships, especially, the economical operation of the units of each voyage, may minimize fuel cost and port charges. This requires low-load streaming cruise control, ballast control, optimal trim, optimal routing, terminal work efficiency improvement, and ship energy management. Optimal routing and terminal work efficiency improvement manage the time saved. To determine the low-load streaming, cruise control, ballast control, optimal trim and ship energy management are meeting the recommendations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.302-307
• /
• 2017

Draft ice in polar regions is formed due to sea level changes and various environmental factors cause damage due to collision with offshore plants and ships for resource development. Drift ice in polar regions is a potential source of accidents for offshore plants that perform long-term operations in one place, as well as on the ship. To prevent accidents with drift ice, offshore plants and ships in polar regions use satellite image information and detection radar to detect drift ice. However, the inability to use visible satellite images at night significantly lowers the detection probability by radar for small drift ice. In this study, we used a thermal imaging system which can be operated day and night for the detection of drift ice, and carried out an experimental study on the detection characteristics of drift ice. To examine the night operation of the thermal imaging system, the experimental condition was set and the thermal image was measured according to the measurement angle change. Under this condition, the correlation was analyzed by theoretical calculating the radiant energy of the drift ice and the sea water.