• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.10 s.115
• /
• pp.1074-1081
• /
• 2006

This paper deals with the dynamic stability analysis of clamped-hinged columns with constant volume. Numerical methods are developed for solving natural frequencies and buckling loads of such columns, subjected to an axial compressive load. The parabolic taper with the regular polygon cross-section is considered, whose material volume and column length are always held constant. Differential equations governing both free vibrations and buckled shapes of such columns are derived. The Runge-Kutta method is used to integrate the differential equations, and the Regula-Falsi method is used to determine natural frequencies and buckling loads, respectively. The numerical methods developed herein for computing natural frequencies and buckling loads are found to be efficient and robust. From the numerical results, dynamic stability regions, dynamic optimal shapes and configurations of strongest columns are reported in figures and tables.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.10
• /
• pp.667-676
• /
• 2015

Working displacement variation by elastic deformation of active Gurney flap which was operated on high frequency was observed. Flap-wise natural frequency was lower than mode analysis result and hinge boundary condition was identified to be the cause through the simple modal test. Design modification for increasing natural frequency was conducted for minimizing the elastic deformation at maximum 35 Hz operating condition which was design requirement condition. Brass bushing was applied instead of rotating bearing for gap minimization and Gurney flap design modification was conducted to increase of the flap-wise natural frequency. Design modification effect was validated by natural frequency comparison with mode analysis result and modal test result of design modification model.

• Journal of the Korean Society of Safety
• /
• v.17 no.2
• /
• pp.8-15
• /
• 2002

In order to investigate the vibration characteristics of fluid-structure interaction problem, we modeled two identical rectangular plates coupled with fluid. A commercial computer code, ANSYS was used to perform finite element analysis and FEM solutions were compared with the experimental results to verify the finite element model. As a result, comparison of FEM and experiment showed good agreement, and the transverse vibration modes, in-phase and out-of-Phase, were observed alternately in the fluid-coupled system. The effect of fluid gap size on the fluid-coupled natural frequency were investigated. It was shown that the mode numbers increased, the normalized natural frequencies monotonically increased. And it was also found that an increase of the fluid gap reduced the coupled natural frequencies for the in-phase modes but increased the coupled natural frequencies for the out-of phase modes, and eventually converged to the results of an infinite fluid gap.

• Structural Engineering and Mechanics
• /
• v.50 no.6
• /
• pp.773-796
• /
• 2014

This paper deals with free vibration analysis of continuous grading fiber reinforced (CGFR) and bi-directional FG annular sector plates on two-parameter elastic foundations under various boundary conditions, based on the three-dimensional theory of elasticity. The plates with simply supported radial edges and arbitrary boundary conditions on their circular edges are considered. A semi-analytical approach composed of differential quadrature method (DQM) and series solution is adopted to solve the equations of motion. Some new results for the natural frequencies of the plate are prepared, which include the effects of elastic coefficients of foundation, boundary conditions, material and geometrical parameters. Results indicate that the non-dimensional natural frequency parameter of a functionally graded fiber volume fraction is larger than that of a discrete laminated and close to that of a 2-layer. It results that the CGFR plate attains natural frequency higher than those of traditional discretely laminated composite ones and this can be a benefit when higher stiffness of the plate is the goal and that is due to the reduction in spatial mismatch of material properties. Moreover, it is shown that a graded ceramic volume fraction in two directions has a higher capability to reduce the natural frequency than conventional one-dimensional functionally graded material. The multidirectional graded material can likely be designed according to the actual requirement and it is a potential alternative to the unidirectional functionally graded material. The new results can be used as benchmark solutions for future researches.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.6
• /
• pp.596-605
• /
• 2022

In this study, analysis of dynamic characteristics and flight vibration was performed to unmanned aerial vehicles. The analysis model was supplemented by performing a dynamic characteristic test and a random vibration test using manufactured dummy aerial vehicle. For the dynamic characteristic test, a bungee cable was used to implement the free end boundary condition. Prior to the flight vibration test using a multiple electric shaker, a random vibration test was performed to predict the excitation force during the actual flight vibration test. It was judged that the actual test could be predicted more accurately by supplementing the analysis model from the test results. In addition, it was possible to determine the feasibility of the test by predicting the excitation force of the flight vibration test.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.568-572
• /
• 2001

An industrial vibratory conveyor system is devised for large-scale feeding by the low-power, using natural frequency of the system. The important thing in this system is to determine the natural frequency and to drive by it. The purpose of this study is to build up reliance on the system with changing of element parameters for vibration characteristics of balancing type vibratory conveyor by using F.E.M. modeling. For investigating the natural frequency, modal testing is performed by using impact hammer, accelerometer and LMS/Vibration Analysis System. Experimental results are compared with F.E.M results. The results of the comparisons within the errors of less than 2 percent can verify the reliability of the F.E.M. analysis of the system. Also we can verify that the characteristics of natural frequency have linearly decreased(-6%) as adding the mass($50{\sim}600kg$). We can find that controlling driving frequency is necessary for triggering the natural frequency, but natural frequency is less affected by adding the mass on the balancing weight.

• Steel and Composite Structures
• /
• v.32 no.3
• /
• pp.305-312
• /
• 2019

In this study, we investigated the effect of fatigue crack propagation of the beams which have a vital importance in engineering applications, on the natural frequency of the system. Beams which have a wide range of applications, are used as fundamental structural elements in engineering structures. Therefore, early detection of any damages in these structures is of vital importance for the prevention of possible destructive damages. One of the widely used methods of early detection of damages is the vibration analysis of the structure. Hence, it is of vital importance to detect and monitor any changes in the natural frequencies of the structure. From this standpoint, in this study we experimentally investigated the effect of fatigue crack propagation on beams produced from 4140 steel, of the natural frequency of the beam. A crack was opened on the $8{\times}16{\times}500mm$ beam using a 3 mm long and 0.25 mm wide wire erosion. The beam, then, underwent 3 point bending tests at 10 Hz with a dynamic fatigue device and its natural frequencies were measured in scheduled intervals and any changes taking place on the natural frequencies of the beam were measured. This data allowed us to identify and measure the crack occurring on the beam subjected to dynamic loading, during the propagation phase. This method produced experimental data. The experimental data showed that the natural frequency of the beam decreased with the propagation of the fatigue crack on the beam.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.1083-1091
• /
• 2009

Modern military equipments are tend to be mounted on a movable truck for their survivability and operation performance. Special units and electronic equipments installed on the truck experience the vibration caused by road roughness during their transport. The level of the transportation vibration is affected by both road conditions and vehicle speeds. In this paper, various experiments on the vibration characteristics of the equipment are carried out via road tests. Transportation vibration is also investigated by numerical analysis using FEM, and natural frequencies and random responses of the launcher are obtained. The PSD and RMS values of acceleration of the equipment are predicted and compared with test results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.171-182
• /
• 2003

Tire vibration modes are known to play a key role in vehicle ride and comfort characteristics. Inputs to the tire such as impacts, rough road surface, tire nonuniformities, and tread patterns can potentially excite tire vibration. In this study, experimental modal analysis on the tire in ground contact are performed by a 3-D impact at the center of contact patch to investigate which modes of tire influence the vibration of wheel and axle. Through the experiment, the vibration transmission properties from tire to axle are examined. And we have compared the influential tire modes when the tire is excited by a vertical impact with those when excited by the 3-D impact. Additionally, the modes of ground contact tire are compared with those of the suspended tire.

• Structural Engineering and Mechanics
• /
• v.7 no.1
• /
• pp.53-67
• /
• 1999

The natural frequencies and modes of free vibration of specially orthotropic elliptic and circular plates are analysed using the Rayleigh-Ritz method. The assumed functions used are two-dimensional boundary characteristic orthogonal polynomials which are generated using the Gram-Schmidt orthogonalization procedure. The first five natural frequencies are reported here for various values of aspect ratio of the ellipse. Results are given for various boundary conditions at the edges i.e., the boundary may be any of clamped, simply-supported or fret. Numerical results are presented here for several orthotropic material properties. For rectilinear orthotropic circular plates, a few results are available in the existing literature, which are compared with the present results and are found to be in good agreement.