• Korean Journal of Materials Research
• /
• v.22 no.4
• /
• pp.180-184
• /
• 2012

Nanostructures of ZnO, such as nanowires, nanorods, nanorings, and nanobelts have been actively studied and applied in electronic or optical devices owing to the increased surface to volume ratio and quantum confinement that they provide. ZnO seed layer (about 40 nm thick) was deposited on Si(100) substrate by RF magnetron sputtering with power of 60 W for 5 min. ZnO nanorods were grown on ZnO seed layer/Si(100) substrate at $95^{\circ}C$ for 5 hr by hydrothermal method with concentrations of $Zn(NO_3)_2{\cdot}6H_2O$ [ZNH] and $(CH_2)_6N_4$ [HMT] precursors ranging from 0.02M to 0.1M. We observed the microstructure, crystal structure, and photoluminescence of the nanorods. The ZnO nanorods grew with hexahedron shape to the c-axis at (002), and increased their diameter and length with the increase of precursor concentration. In 0.06 M and 0.08 M precursors, the mean aspect ratio values of ZnO nanorods were 6.8 and 6.5; also, ZnO nanorods had good crystal quality. Near band edge emission (NBE) and a deep level emission (DLE) were observed in all ZnO nanorod samples. The highest peak of NBE and the lower DLE appeared in 0.06 M precursor; however, the highest peak of DLE and the lower peak of NBE appeared in the 0.02 M precursor. It is possible to explain these phenomena as results of the better crystal quality and homogeneous shape of the nanorods in the precursor solution of 0.06 M, and as resulting from the bed crystal quality and the formation of Zn vacancies in the nanorods due to the lack of $Zn^{++}$ in the 0.02 M precursor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.13-17
• /
• 2006

The one-dimensional ZnO nanostructures prepared through thermal evaporation under various cooling down procedures by changing the flow rates of the carrier gas and the reactive gas were investigated. The nanorod structures were changed into the nanonail types with a broad head through the reduction of the flow rate of the carrier gas. The decrease of the reactive gas reduced the length of the nail heads due to the limited mass transport of reactive gas. The intensity ratio of the ultraviolet emission/green emission of photoluminescence was proportional to the length of the broad head showing a larger surface area. The vertically aligned nanostructures were grown along the [0001] direction of ZnO regardless of the aligned directions. The crystal direction of the nanostructures was determined by that of the initial ZnO crystal.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.4
• /
• pp.229-234
• /
• 2017

In this study, we fabricated a TFT gas sensor with ZnO nanorods grown by hydrothermal synthesis. The suggested devices were compared with the conventional ZnO film-type TFTs in terms of the gas-response properties and the electrical transfer characteristics. The ZnO seed layer is formed by atomic-layer deposition (ALD), and the precursors for the nanorods are zinc nitrate hexahydrate ($Zn(NO_3)_2{\cdot}6H_2O$) and hexamethylenetetramine ($(CH_2)6N_4$). When 15 ppm of NO gas was supplied in a gas chamber at $150^{\circ}C$ to analyze the sensing capability of the suggested devices, the sensitivity (S) was 4.5, showing that the nanorod-type devices respond sensitively to the external environment. These results can be explained by X-ray photoelectron spectroscopy (XPS) analysis, which showed that the oxygen deficiency of ZnO nanorods is higher than that of ZnO film, and confirms that the ZnO nanorod-type TFTs are advantageous for the fabrication of high-performance gas sensors.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.35.1-35.1
• /
• 2009

Vertically aligned zinc oxide (ZnO) nanorods (NRs) with different surface morphology were grown by metal organic chemical vapor deposition (MOCVD) on sapphire substrate. The films thus prepared were characterized by measuring X-ray diffraction (XRD), Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM) studies. To study the effect of surface morphology on wettability, the contact angle (CA) of water was measured. It was demonstrated that the CA of the deposited ZnO NRs varied between $104^{\circ}$ and $135^{\circ}$ depending upon the surface morphology. Variable temperature photoluminescence (PL) have employed to probe the exciton recombination in high density and vertically aligned ZnO Nanorod arrays. The low-temperature PL characterizes the dominant near-band-edge excitonic emissions from such nanorod arrays.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1251-1254
• /
• 2008

ZnO:Zn films have been deposited on the glass substrates using thermal vapor deposition method. Different morphologies such as ZnO slice, pillar and nanorod have been derived. The relationship between photoluminescence and morphology has been studied. Photocatalytic activity has been performed to validate that defects play an important role in the photoluminescence process.

• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.668-672
• /
• 2003

The ZnO nanorods were synthesized using vapor-solid (VS) method on sodalime glass substrate without the presence of metal catalyst. ZnO nanorods were prepared thermal evaporation of Zn powder at $500^{\circ}C$. As-fabricated ZnO nanorods had an average diameter and length of 85 nm and 1.7 $\mu\textrm{m}$. Transmission electron microscopy revealed that the ZnO nanorods were single crystalline with the growth direction perpendicular to the (101) lattice plane. The influences of reaction time on the formation of the ZnO nanorods were investigated. The photoluminescence measurements showed that the ZnO nanorods had a strong ultraviolet emission at around 380 nm and a green emission at around 500 nm.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1605-1610
• /
• 2017

The electrochemical luminescence (ECL) device was investigated, which has similar structure to the dye-sensitized solar cell. The structure of the ECL cell in this experiment reliably induces a large amount of the oxidation around electrodes. The band gap of the ECL electrode is of 3.0 - 3.2 eV. Titanium dioxide ($TiO_2$) nanoparticle has following properties: a band gap of 3.4 eV, a low-priced material, and 002 preferred orientation (Z-axis). Zinc Oxide (ZnO) nanorod is easy to grow in a vertical direction. In this paper, in order to determine material suitable for the ECL device, the properties of various materials for electrodes of ECL devices such as ZnO nanorod (ZnO-NR) and $TiO_2$ nanoparticle ($TiO_2-NP$) were compared. The threshold voltage of the light emission of the ZnO-NR was 2.0 V which is lower than 2.5 V of $TiO_2-NP$. In the other hand, the luminance of $TiO_2-NP$ was $44.66cd/m^2$ and was higher than that of $34cd/m^2$ of ZnO-NR at the same applied voltage of 4 V. Based on the experimental results, we could conclude that $TiO_2-NP$ is a more suitable electrode material in ECL device than the ZnO-NR.

• 한국전기화학회:학술대회논문집
• /
• 2003.10a
• /
• pp.42-42
• /
• 2003

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.49-49
• /
• 2010

Nanopiezotronics is an emerging area of nanotechnology with a variety of applications that include piezoelectric field-effect transistors and diodes, self-powered nanogenerators and biosystems, and wireless nano/biosensors. By exploiting coupled piezoelectric and semiconducting characteristics, it is possible for nanowires, nanobelts, or nanorods to generate rectifying current and potential under external mechanical energies such as body movement (handling, winding, pushing, and bending) and muscle stretching, vibrations (acoustic and ultrasonic waves), and hydraulic forces (body fluid and blood flow). Fully transparent, flexible (TF) nanogenerators that are operated by external mechanical forces will be presented. By controlling the density of the seed layer for ZnO nanorod growth, transparent ZnO nanorod arrays were grown on ITO/PES films, and a TF conductive electrode was stacked on the ZnO nanorods. The resulting integrated TF nanodevice (having transparency exceeding 70 %) generated a noticeable current when it was pushed by application of an external load. The output current density was clearly dependent on the force applied. Furthermore, the output current density depended strongly on the morphology and the work function of the top electrode. ZnO nanorod-based nanogenerators with a PdAu, ITO, CNT, and graphene top electrodes gave output current densities of approximately $1-10\;uA/cm^2$ at a load of 0.9 kgf. Our results suggest that our TF nanogenerators are suitable for self-powered TF device applications such as flexible self-powered touch sensors, wearable artificial skins, fully rollable display mobile devices, and battery supplements for wearable cellular phones.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.4
• /
• pp.155-159
• /
• 2008

In this work, we report synthesis of free-standing ZnO/Zn core-shell micro-polyhedrons using metal Zn pellets as a source material by the thermal chemical vapor deposition process. Scanning and transmission electron microscopy measurements were introduced to investigate morphologies and structural properties of as-grown ZnO/Zn core-shell micro-polyhedrons. It was found that micro-polyhedrons were composed of inner single-crystalline metal Zn surrounded by single-crystalline ZnO nanorod arrays. The inner single crystalline metal Zn with micro-scale diameter has a hexagonal crystal structure. Diameter and height of ZnO nanorods covering the metal Zn surface are below 10 nm and 100 nm, respectively. It was also confirmed that c-axis oriented ZnO nanorods are single crystalline with a hexagonal crystal structure.