• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.354.1-354.1
• /
• 2016

Nanoporous gold (NPG) is a very promising material in various fields such as sensor, actuator, and catalysis because of its high surface to volume ratio and conducting nature. In this study, we fabricated a NPG based amperometric sensor on a glass substrate by means of co-sputtering of Au and Si. During the sputtering process, we found the optimum conditions for heat treatment to reduce the residual stress and to improve adhesion between NPG films and the glass substrate. Subsequently, Si was selectively etched from Au-Si alloy by KOH solution, which forms nanoporous structures. Scanning electron microscopy (SEM) and auger electron spectroscopy (AES) were used to estimate the structure of NPG films and their composition. By employing appropriate heat treatments, we could make very stable NPG films. We tested the performance of NPG sensor with aniline molecules, which shows high sensitivity for sensing low concentration of aniline.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.4
• /
• pp.251-255
• /
• 2010

We report on the electrocatalytic reduction of hydrogen peroxide at nanoporous gold (NPG) surfaces. Various NPG surfaces with different surface structure were prepared by changing the conditions of electrodeposition for Ag-Au layers such as the concentration ratios of $KAu(CN)_2$ over $KAg(CN)_2$ and deposition charges. The effects of different electrochemical conditions on the electrocatalysis of $H_2O_2$ reduction were investigated. The NPG surfaces exhibited sensitive amperometric responses for $H_2O_2$ reduction, from which calibration plots with higher sensitivity than a bare Au surface were obtained.

• Journal of the Korean Chemical Society
• /
• v.63 no.1
• /
• pp.45-50
• /
• 2019

Because arsenic (As) is a chemical substance toxic to humans, there have been extensive investigations on the development of As detection methods. In this study, the electrochemical determination of As on nanoporous gold (NPG) electrodes was investigated using anodic stripping voltammetry. The electrochemical surface area of the NPG electrodes was controlled by changing the reaction times during the anodization of Au for NPG preparation, and its effect on the electrochemical behavior during As detection was examined. The detection efficiency of the NPG electrodes improved as the roughness factor of the NPG electrodes increased up to around 100. A further increase in the surface area of the NPG electrodes resulted in a decrease of the detection efficiency due to high background current levels. The most efficient As detection efficiency was obtained on the NPG electrodes prepared with an anodization time of 50 s. The effects of the detection parameters and of the Cu interference in As detection were investigated and the NPG electrode was compared to flat Au electrodes.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.2
• /
• pp.83-89
• /
• 2012

We investigate the electrocatalytic activities for oxygen reduction at nanoporous gold (NPG) surfaces fabricated by selective dissolution of Ag from electrodeposited Ag-Au layers on electrode surfaces. The structure of NPG was controlled by changing the concentration ratios of precursor metal complexes during the electrodeposition of Ag-Au layers and the corresponding surface morphology and surface area was examined. NPG structures with Ag/Au ratio of 2.0 exhibited the highest electrocatalytic activity for oxygen reduction, where the nanoporous structure plays a key role, but the surface area does not affect on the electrocatalytic activity. The mechanism of electroreduction of oxygen was investigated by rotating disk electrode techniques. In acidic media, oxygen was first reduced to hydrogen peroxide followed by further reduction to water through 2-step 4-electron mechanism, whereas the oxygen was reduced directly to water by 4-electron mechanism in basic media.

• Journal of the Korean Chemical Society
• /
• v.66 no.6
• /
• pp.436-441
• /
• 2022

Because the nanoporous electrodes has large electrochemical surface areas, extensive studies have been focused on their fabrication methods. In this paper, a method for introducing a nanoporous gold (NPG) structure on the surface of an ultramicroelectrode (UME) using potentiostatic anodization was investigated. A well-defined NPG structure was introduced on the surface of the UME when a potential of 1.3 V was applied in 0.1 M phosphate buffer solution (pH 8) containing 1 M KCl. The anodic oxidation efficiency was investigated by observing the effect of the applied potential, the reaction time, and the size of the electrode on the roughness factor (R_f) of the prepared NPG-UMEs. In a short time of about 10 minutes, NPG-UME with a large R_f value of about 2000 could be prepared, which could be effectively used for electrochemical glucose detection. The results shown in this work are expected to have great applicability when performing electrochemical analysis with a small sample volume.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.575-578
• /
• 2011

We fabricated a novel simple and rapid method of three dimensional nanoporous gold thin film (NPGF) onto a Au substrate using electrochemical deposition method. The NPGF-modified electrode analysis by scanning electron microscope and reveals the formation of nanopores, approximately 30~50 nm in diameter. differential pulse voltammetry was measured for the determination of ${\gamma}$-aminobutiric acid in the concentration range of ($10{\sim}100{\mu}M$ using a NPGF. The high sensitivity feature of NPGF is expected to be applied for real sample biosensor applications.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.2
• /
• pp.74-80
• /
• 2013

We investigate the formation of nanoporous gold (NPG) surfaces by anodization in three carboxylic acid (formic acid, acetic acid, and propionic acid) solutions and the electrochemical oxidation of glucose at NPG surfaces. Among three carboxylic acids, formic acid provided the most efficient conditions for NPG formation towards glucose oxidation. The optimized conditions during anodization in formic acid for glucose oxidation were 5.0 V of applied potential and 4 hour of reaction time. Electrocatalytic activities for glucose oxidation at NPG surfaces prepared by anodization in carboxylic acids were examined under the absence and presence of chloride ions, which were compared to those observed at NPG prepared in oxalic acid solutions. The application NPG prepared by optimized anodization conditions in formic acid to the amperometric detection of glucose was demonstrated.

• Journal of the Korean Institute of Gas
• /
• v.12 no.2
• /
• pp.32-37
• /
• 2008

For a development of U-safety system, liquid/gas-sensors that are easy to carry and install in any place are needed. Therefore, in this work, we prepared porous gold using a templating method with nanoporous alumina, and it was used as sensing materials and electrode. The resulting materials showed high purity macroporous structure with $200{\sim}300\;nm$ of window-pore and $4.8\;m^2/g$ of surface area. Because porous gold had good electric conductivity, convenience to measure the change of electric resistivity and good reproducibility, it could be used as potential sensing materials. As a proof-of-concept test, the detection test for mercury ion was carried out.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1777-1780
• /
• 2012

• Proceedings of the Korean Vacuum Society Conference
• /
• 2007.02a
• /
• pp.48-48
• /
• 2007