• International Journal of Concrete Structures and Materials
• /
• v.5 no.1
• /
• pp.3-10
• /
• 2011

Theoretical models for prediction of the mechanical properties of cement mortar are developed based on the morphology and interactions of cement hydration products, capillary pores and microcracks. The models account for intermolecular interactions involving the nano-scale calcium silicate hydrate (C-S-H) constituents of hydration products, and consider the effects of capillary pores as well as the microcracks within the hydrated cement paste and at the interfacial transition zone (ITZ). Cement mortar was modeled as a three-phase material composed of hydrated cement paste, fine aggregates and ITZ. The Hashin's bound model was used to predict the elastic modulus of mortar as a three-phase composite. Theoretical evaluation of fracture toughness indicated that the frictional pullout of fine aggregates makes major contribution to the fracture energy of cement mortar. Linear fracture mechanics principles were used to model the tensile strength of mortar. The predictions of theoretical models compared reasonably with empirical values.

• Journal of the Korean Ceramic Society
• /
• v.48 no.6
• /
• pp.636-640
• /
• 2011

Nano-sized cobalt (II) oxide nanoparticles with a high crystallinity were synthesized using thermolysis of a $Co^{2+}$-oleate precursor at 310$^{\circ}C$. The phase and morphology of as-prepared cobalt oxide nanoparticles were characterized using X-ray diffraction, high-resolution transmission electron microscopy, and Brunauer-Emmett-Teller surface area measurements. The cobalt oxide nanoparticles were found to be spherical nanoclusters with an average diameter of approximately 200 nm, consisting of tiny nanocrystals (10-20 nm). Furthermore, the Li electroactivites of the cobalt oxide nanoparticles were investigated using cyclic voltammetry and galvanostatic cycling. The cobalt oxide nanoparticles could deliver high capacities over 420 mA h $g^{-1}$ at a C/5 current rate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.241-246
• /
• 2016

ZnO thin films have wide application areas due to its versatile properties as transparent conductors, wide-bandgap n-type semiconductors, gas sensor materials, and etc. We have performed a systematic investigation on ultraviolet-assisted CVD (chemical vapor deposition) method. Ultraviolet irradiation during the deposition of ZnO causes chemical reduction on the growing surface; which results in the reduction of the deposition rate, increase in the surface roughness, and decrease of the electrical resistivity. These effects produce larger characteristic variation with various deposition conditions in terms of surface morphology and optical/electrical properties compared to normal CVD deposited ZnO thin films. This versatile controllability of ultraviolet-assisted CVD can provide a larger processing options in the fabrication of nano-structured materials and flexible device applications.

• Membrane and Water Treatment
• /
• v.7 no.6
• /
• pp.555-571
• /
• 2016

Heavy metal contamination has attracted considerable attention during recent decades due to the potential risk brought about for human beings and the environment. Several adsorbent materials are utilized for the purification of contaminated water resources among which chitosan is considered as an appropriate alternative. Copper is a heavy metal contaminants found in several industrial wastewaters and its adsorption on porous and macroporous chitosan membranes is investigated in this study. Membranes are prepared by phase inversion and particulate leaching method and their morphology is characterized using SEM analysis. Batch adsorption experiments are performed and it is found that copper adsorption on macroporous chitosan membrane is higher than porous membrane. The iso-steric heat of adsorption was determined by analyzing the variations of temperature to investigate its effect on adsorption characteristics of macroporous chitosan membranes. Furthermore, desorption experiments were studied using NaCl and EDTA as eluants. The mechanism of copper adsorption was also investigated using XPS spectroscopy which confirms simultaneous occurrence of chelation and electrostatic adsorption mechanisms.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1692-1696
• /
• 2008

In this paper, we characterize the mechanical properties of PCL strand which is made by oscillating nozzle for tissue engineering scaffold. In order to increase the mechanical properties of the PCL strand, we designed an oscillating nozzle system for the 3D plotting system. First, we check the effect of the nozzle speed (3 to 8 mm/sec), frequency (0 or 300 Hz) and the oscillating amplitude (0 or 100 V) on the diameter of the PCL strand. Second, we observe the effect of the frequency (0, 100, 200 and 300 Hz) and the oscillating amplitude (0, 50 and 100 V) on the mechanical property of PCL strand. The mechanical properties and surface morphology of PCL strand made by oscillating nozzle are compared with the PCL strand made by normal nozzle using Nano-UTM and SEM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.295-295
• /
• 2010

Nanoparticles of the compound semiconductor, Cu(In, Ga)Se2 (CIGS), were synthesized in solution under ambient pressure below $100^{\circ}C$ and characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption spectroscopy and energy-dispersive X-ray (EDX) analyses. These materials have chalcopyrite crystal structures and the particle sizes less than 100 nm. Synthetic conditions were studied for the crystallized CIGS nanoparticles formation to prevent from side products of Cu2Se, Cu2-xSe, and CuSe etc. The single phase CIGS nanoparticles were applied to coating of thin films photovoltaic cells. The electro deposition of CIGS thin films is also a good non-vacuum technology and under investigation. In aqueous solutions, the different chemical compositions of CIGS thin films were obtained, depending on pH, concentration of starting materials and deposition potentials. The surface morphology of the prepared CIGS thin films depends on the complexing ligands to the solutions during the electrochemical deposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.299-300
• /
• 2005

본 연구에서는 $SiO_2$ 판상체 위에 저굴절 및 고굴절 금속 산화물을 다층 교차 증착하여 Pearl Pigment를 sputtering 공법을 이용하여 증착하였다. Pearl Pigment는 Essential Macleod program 을 이용한 색상과 증착된 pigment의 색상이 파장에 따라 blue, violet, pink, red, orange, yellow, green 등(Wave length : 450$\sim$730 nm)으로 동일하게 나타났고, 기존의 제품에 비해 색상효과가 뛰어나고, 표면 morphology가 우수하였다. 주사전자현미경(SEM)으로 막 두께, 표면 조직 및 입자 크기를 측정하였고, 스펙트로미터를 사용하여 각각의 파장을 분석하였으며 EDS, XRD를 이용하여 정성 및 정량 분석을 하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.183-184
• /
• 2005

Four different coatings deposited using cold spray process were studied with two different powder agglomerating techniques (spray d교 and evaporated powder) and using $TiO_2$ nano-sized powders with and without a 10wt% addition of ZnO. Characterization was performed by SEM, XRD and roughness test. Also the photocatalytic effect of the coatings was evaluated. Although the change of powder preparation techniques and the addition of ZnO into $TiO_2$ did not show appreciable variations in the surface morphology and Anatase phase transformation, it did show influence on the surface roughness of the coating, the highest roughness being found in the coatings made by spray powder prepared method. Regarding the photocatalytic effect it was observed that the using the spray dry coating and the addition of ZnO are promoter of purification at higher rates.

• Korea-Australia Rheology Journal
• /
• v.17 no.2
• /
• pp.41-45
• /
• 2005

As an effort to explore the effective use of carbon nanotubes as a reinforcing material for advanced nano-composites with polymer matrices, multi-walled carbon nanotubes (MWNTs) were successfully incorporated into polystyrene (PS) via in-situ bulk polymerization. Various experimental techniques revealed that the covalent bonds formed between PS radicals and acid-treated carbon nanotubes are favorable resulting in an effective load transfer. The enhanced storage modulus of the nanocomposites suggests a strong possibility for the potential use in industrial applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.560-560
• /
• 2012

We report a one-step fabrication method of Poly(9,9-dioctylfluorene) (PFO) nanowire array with pronounced ${\beta}$-Phase. We use liquid-bridge-mediated nanotransfer molding (LB-nTM) which is a new direct nano-patterning method based on the direct transfer of various materials from a mold to a substrate via liquid layer. The formation of the ${\beta}$-phase morphology in the resulting PFO nanowire array was evidenced by the presence of an absorption peak at 435nm. With the collection polarizer oriented parallel to the wire long axis, the PL emission was most intense and an emission dichroic ratio, DRE, of 3.7 was determined. The nanowire array have been investigated by scanning electron microscopy (SEM). Also, we simply fabricated structure of device of ITO/PFO nanowire arrays/Al and the electroluminescence spectra were recorded at various applied voltage.