• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.288-289
• /
• 2011

Indium Tin Oxide (ITO) is a typical highly Transparent Conductive Oxide (TCO) currently used as a transparent electrode material. Most widely used deposition method is the sputtering process for ITO film deposition because it has a high deposition rate, allows accurate control of the film thickness and easy deposition process and high electrical/optical properties. However, to apply high quality ITO thin film in a flexible microelectronic device using a plastic substrate, conventional DC magnetron sputtering (DMS) processed ITO thin film is not suitable because it needs a high temperature thermal annealing process to obtain high optical transmittance and low resistivity, while the generally plastic substrates has low glass transition temperatures. In the room temperature sputtering process, the electrical property degradation of ITO thin film is caused by negative oxygen ions effect. This high energy negative oxygen ions(about over 100eV) can be critical physical bombardment damages against the formation of the ITO thin film, and this damage does not recover in the room temperature process that does not offer thermal annealing. Hence new ITO deposition process that can provide the high electrical/optical properties of the ITO film at room temperature is needed. To solve these limitations we develop the Magnetic Field Shielded Sputtering (MFSS) system. The MFSS is based on DMS and it has the plasma limiter, which compose the permanent magnet array (Fig.1). During the ITO thin film deposition in the MFSS process, the electrons in the plasma are trapped by the magnetic field at the plasma limiters. The plasma limiter, which has a negative potential in the MFSS process, prevents to the damage by negative oxygen ions bombardment, and increases the heat(-) up effect by the Ar ions in the bulk plasma. Fig. 2. shows the electrical properties of the MFSS ITO thin film and DMS ITO thin film at room temperature. With the increase of the sputtering pressure, the resistivity of DMS ITO increases. On the other hand, the resistivity of the MFSS ITO slightly increases and becomes lower than that of the DMS ITO at all sputtering pressures. The lowest resistivity of the DMS ITO is $1.0{\times}10-3{\Omega}{\cdot}cm$ and that of the MFSS ITO is $4.5{\times}10-4{\Omega}{\cdot}cm$. This resistivity difference is caused by the carrier mobility. The carrier mobility of the MFSS ITO is 40 $cm^2/V{\cdot}s$, which is significantly higher than that of the DMS ITO (10 $cm^2/V{\cdot}s$). The low resistivity and high carrier mobility of the MFSS ITO are due to the magnetic field shielded effect. In addition, although not shown in this paper, the roughness of the MFSS ITO thin film is lower than that of the DMS ITO thin film, and TEM, XRD and XPS analysis of the MFSS ITO show the nano-crystalline structure. As a result, the MFSS process can effectively prevent to the high energy negative oxygen ions bombardment and supply activation energies by accelerating Ar ions in the plasma; therefore, high quality ITO can be deposited at room temperature.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.328-332
• /
• 2010

In this study, porous ZnO sphere and Cu-ZnO composite were synthesized by coprecipitation method in diethylene glycol solvent. The physicochemical properties of as-prepared composite materials were characterized by SEM, XRD, $N_2$-sorption and $H_2$-TPR. A series of porous Cu-ZnO with different Cu contents (0, 6.6, 21.3, 36.4, 54.6, 77.8 wt%) was investigated for CO oxidation activity in a fixed bed reactor system. With increasing Cu content in Cu-ZnO the surface area and micropore volume of Cu-ZnO are decreased and Cu (36.4 wt%)-ZnO shows higher activity for CO oxidation compared to the others.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.23-29
• /
• 2013

Development of flexible electronic devices has primarily focused on printing technology using organic materials. However, organic-based flexible electronics have several disadvantages, including low electrical performance and long-term reliability. Therefore, we fabricated nano- and micro-thick silicon film attached to the polymer substrate using transfer printing technology to investigate the feasibility of silicon-based flexible electronic devices with high performance and high flexibility. Flexibility of the fabricated samples was investigated using bending and stretching tests. The failure bending radius of the 200 nm-thick silicon film attached on a PI substrate was 4.5 mm, and the failure stretching strain was 1.8%. The failure bending radius of the micro-thick silicon film attached on a FPCB was 2 mm, and the failure strain was 3.5%, which showed superior flexibility compared with conventional silicon material. Improved flexibility was attributed to a buffering effect of the adhesive between the silicon film and the substrate. The superior flexibility of the thin silicon film demonstrates the possibility for flexible electronic devices with high performance.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.1
• /
• pp.20-26
• /
• 2015

Ceramic ink-jet printing technology in art tiles, decorated tablewares and other porcelain products has many advantages of fast and precision printing of various images with high efficiency and low cost. For the application to ink-jet printing, ceramic ink requires a stable dispersibility with nano-sized pigments. In this paper, characteristics of pink-red aqueous ceramic ink for ink-jet printing was demonstrated. $CaCr_{0.1}Sn_{0.8}SiO_5$ pigment was synthesized using solid state reaction and deagglomerated using attrition milling. The aqueous ceramic ink contains 10 wt% of the obtained $CaCr_{0.1}Sn_{0.8}SiO_5$ nanopigment with 0.4 wt% of sodium dodecyl sulfate (SDS) as a dispersion agent. Viscosity of $CaCr_{0.1}Sn_{0.8}SiO_5$ aqueous ceramic ink was adjusted using 0.18 wt% of polyvinyl alcohol (PVA) for a suitable jetting from the nozzle. The prepared pink-red ceramic ink showed a good jetting property with formation of a single sphere-shaped droplet after $180{\mu}s$ without a tail and satellite droplet.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.8
• /
• pp.1719-1723
• /
• 2009

The LiFeP$O_4$ powder was synthesized by using the solid state reaction method with Fe($C_2O_4){\cdot}2H_2O,\;(NH_4)_2HPO_4,\;Li_2CO_3$, and chitosan as a carbon precursor material for a cathode of a lithium-ion battery. The chitosan added LiFePO4 powder was calcined at 350 ${^{\circ}C}$ for 5 hours and then 800 ${^{\circ}C}$ for 12 hours for the calcination. Then we calcined again at 800 ${^{\circ}C}$ for 12 hours. We characterized the synthesized compounds via the crystallinity, the valence states of iron ions, and their shapes using TGA, XRD, SEM, TEM, and XPS. We found that the synthesized powders were carbon-coated using TEM images and the iron ion is substituted from 3+ to 2+ through XPS measurements. We observed voltage characteristics and initial charge-discharge characteristics according to the C rate in LiFeP$O_4$ batteries. The obtained initial specific capacity of the chitosan added LiFeP$O_4$ powder is 110 mAh/g, which is much larger than that of LiFeP$O_4$ only powder.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.582-587
• /
• 2012

In this paper, it was studied on the crystallization characteristics of PLA film by adding ammonium phosphate (APP) as a nucleation agent. Crystallinity and crystallite size of PLA film were determined by Scherrer equation. Crystallization rate constant of PLA film was calculated through Avrami equation. Film samples in the study were prepared by two steps. PLA films were prepared by adding 1, 5, and 10 wt%, respectively, at first and was secondly annealed at 130, 140, and $150^{\circ}C$. Crystallinity of pure PLA film was average 4.6% and those of PLA film with adding 1, 5, and 10 wt% APP were 12.2, 47.7, and 50.0%, respectively. Crystallite size of PLA film was average 28.0 nm and those of PLA film with adding 1, 5, and 10 wt% APP were 26.8, 24.0, and 19.0 nm, respectively. Crystallization rate constants of PLA film with 1 wt% APP were 2.12, 3.86, and 0.27 by annealing at 130, 140, and $150^{\circ}C$, respectively, where was higher than pure PLA film and those with adding 5 and 10 wt% APP, respectively.

• Journal of Korea Port Economic Association
• /
• v.25 no.4
• /
• pp.107-130
• /
• 2009

Future of Busan New Port may depend even on the efficient use of the port hinterland. Accordingly, selection of which industry according to which standard in the port hinterland is another task. In order to solve this problem, it analyzed the structure in international division of labor with China and Japan, which are possessing considerable portion in the trading volume with our country, and the export-import structure of Busan Port against China and Japan, by using RCA index and GL index as well as export-import results. In addition to this, the proper industry was selected on the basis of 10 strategic industries for development in Busan. According to the analytical results, the industries, which will be induced in the hinterland of Busan New Port, include textile clothing, pulp printing matter, jewelry, basic metal nonmetallic product, machine lectric product, automobile, shipbuilding, optics accurate machinery medical treatment musical instrument, nano material, fuel battery, aerospace and intelligent robot.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.4
• /
• pp.173-181
• /
• 2018

Recently composite materials have dominated most engineering fields, owing to their better performance, increased durability and flexibility to be customized and designed for a specific required property. This has given them unprecedented superiority over conventional materials. With the help of the ever increasing computational capabilities of computers, researchers have been trying to develop accurate material models for the complex and integrated properties of these composites. This has led to advances in virtual testing of composite materials as a supplement or a possible replacement of laboratory experiments to predict the properties and responses of composite materials and structures. This paper presents a review on the complex multi-scale modelling framework of the virtual testing machines, which involve computational mechanics at various length-scales starting with nano-mechanics and ending in structure level computational mechanics, with a homogenization technique used to link the different length scales. In addition, the paper presents the features of some of the biggest integrated virtual testing machines developed for study of concrete, including a multiscale modeling scheme for the simulation of the constitutive properties of nanocomposites. Finally, the current challenges and future development potentials for virtual test machines are discussed.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.2 s.52
• /
• pp.135-145
• /
• 2007

The needs for the ultra fine particles have been increased in preparation field of raw powders such as fine ceramics and high functional products. In this study, a series of wet grinding experiments were carried out on inorganic powders such as calcite, pyrophyllite and talc by a stirred ball mill. The particle size distribution of ground products of each test material fur a given grinding time was found to be expressed by the grinding rate (selection function) which was obtained from the grinding kinetics analysis. The median diameter decreased from 6.49 to $0.47{\mu}m$ in calcite, and decreased from 3.91 to $1.14{\mu}m$ in pyrophyllite. However, in talc, median diameter was decreased a little bit from 10.30 to $6.67{\mu}m$. The grinding rate changing on calcite and pyriphyllite were similar at the same conditions. However, in the case of talc, it was observed that the grinding rate was not increased compared to other samples.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.49-55
• /
• 2018

Under the era of energy crisis, hydrogen energy is considered as one of the most potential alternative energies. Liquid hydrogen has much higher energy density per unit volume than gas hydrogen and is counted as the excellent energy storage method. In this study, Navier-Stokes equations based on 2-phase model were solved by using a computational fluid dynamics program and the liquefaction process of gaseous hydrogen passing through a cryogenic cooling tube was analyzed. The copper with high thermal conductivity was assumed as the material for cryogenic cooling tube. For different inlet velocities of 5 m/s, 10 m/s and 20 m/s for hydrogen gas, the distributions of fluid temperature, axial and radial velocities, and volume fractions of gas and liquid hydrogens were compared. These research results are expected to be used as basic data for the future design and fabrication of cryogenic cooling tube to transform the hydrogen gas into liquid hydrogen.