• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.146-146
• /
• 2011

The blue light emitting diode (LED) structure based on non-polar a-plane (11-20) GaN which was coated TiO2 nanoparticles using spin coating method was grown on r-plane (1-102) sapphire substrates to improve light extraction efficiency. We report on the emission and structural properties with temperature dependence of photoluminescence (PL) and x-ray rocking curves (XRC). From PL results at 13 K of undoped GaN samples, basal plane stacking fault (BSF) and near band edge (NBE) emission peak were observed at 3.434 eV and 3.484 eV, respectively. We also found the temperature-induced band-gap shrinkage, which was fitted well with empirical Varshini's equation. The PL intensity of TiO2 nanoparticles ?coated multiple quantum well (MQW) sample is decayed slower than that of no coating sample with increasing temperature. The anisotrophic strain and azimuth angle dependence in the films were shown from XRC results. The full width at half maximum (FWHM) along the GaN [11-20] and [1-100] directions were 564.9 arcsec and 490.8 arcsec, respectively. A small deviation of FWHM values at in-plane direction is attributed to uniform in-plane strain.

• Journal of Pharmaceutical Investigation
• /
• v.37 no.1
• /
• pp.15-22
• /
• 2007

An oil-in-water solvent evaporation method was used to prepare the cyclosporin A (CyA)-loaded nanoparticles varying in poly (D,L-lactide-co-glycolide) (PLGA) polymer (RG 502H, RG 503H) and the amount of additive ethyl myristate (EM) or chitosan (CS). The particles were characterized for drug loading and entrapment efficiency by HPLC, surface morphology by scanning electron microscopy, particle size by dynamic light scattering and surface charge by Zetapotential. The results showed drug loadings ranging from 10.9% to 15.8% with high encapsulation efficiency (82.0-97.8%). SEM and DLS studies showed discrete and spherical particles with smooth surfaces and mean size ranging 257.6-721.7 nm. The additive EM or CS did not change the mean sizes of the nanoparticles, whereas by the coating effect of CS, the Zetapotential values of the CS-added nanoparticles were moved to the more positive direction as the amount of CS was increased. From the pharmacokinetic analysis, the nanoparticles formulations showed the higher bioavailability and MRT than $Neoral^{\circledR}$ While little adding effect of EM or CS was detected in pharmacokinetic profile when RG 503H was used as polymer carrier, more noticeable different pharmacokinetic behaviors could be observed in case of RC 502H. EM incorporation was found to elevate the $K_{el}$, whereas CS coating resulted in the decrease of F and $K_{el}$, which seems to be due to the function of CS as a barrier and a mucoadhesive coating.

• Membrane and Water Treatment
• /
• v.10 no.4
• /
• pp.287-298
• /
• 2019

Lotus leaf has a special dual micro and nano surface structure which gives its highly hydrophobic surface characteristics and so-called self cleaning effect. In order to endow PVDF hollow fiber membrane with this special structure and improve the hydrophobicity of membrane surface, PVDF hollow fiber composite membranes was obtained through the immersion coating of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) dilute solution on the outside surface of PVDF support membrane. The prepared PVDF composite membranes were used in the vacuum membrane distillation (VMD) for the desalination. The effects of PVDF-HFP dilute solution concentration in the dope solution and coating time on VMD separation performance was studied. Membranes were characterized by SEM, WCA measurement, porosity, and liquid entry pressure of water. VMD test was carried out using $35g{\cdot}L^{-1}$ NaCl aqueous solution as the feed solution at feed temperature of $30^{\circ}C$ and the permeate pressure of 31.3 kPa. The vapour flux reached a maximum when PVDF-HFP concentration in the dilute solution was 5 wt% and the coating time was kept in the range of 10-60 s. This was attributed to the well configuration of micro-nano rods which was similar with the dual micro-nano structure on the lotus leaf. Compared with the original PVDF membrane, the salt rejection can be well maintained which was greater than 99.99 % meanwhile permeation water conductivity was kept at a low value of $7-9{\mu}S{\cdot}cm^{-1}$ during the continuous testing for 360 h.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.691-699
• /
• 2008

Electrochemical characteristics of Ti-30Ta-xZr alloys coated with HA/TiN by using magnetron sputtering method were studied. The Ti-30Ta containing Zr(3, 7, 10 and 15wt%) were 10 times melted to improve chemical homogeneity by using a vacuum furnace and then homogenized for 24hrs at $1000^{\circ}C$. The specimens were cut and polished for corrosion test and coating, and then coated with HA/TiN, respectively, by using DC and RF-magnetron sputtering method. The analyses of coated surface and coated layer were carried out by using optical microscope(OM), field emission scanning electron microscope(FE-SEM) and X-ray diffractometer(XRD). The electrochemical characteristics were examined using potentiodynamic (-1,500 mV~ + 2,000 mV) and A.C. impedance spectroscopy(100 kHz ~ 10 mHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The microstructure of homogenized Ti-30Ta-xZr alloys showed needle-like structure. In case of homogenized Ti-30Ta-xZr alloys, a-peak was increased with increasing Zr content. The thickness of TiN and HA coated layer showed 400 nm and 100 nm, respectively. The corrosion resistance of HA/TiN-coated Ti-30Ta-xZr alloys were higher than that of the non-coated Ti-30TaxZr alloys, whic hindicate better protective effect. The polarization resistance($R_p$) value of HA/TiN coated Ti-30Ta-xZr alloys showed $8.40{\times}10^5{\Omega}cm^2$ which was higher than that of non-coated Ti-30Ta-xZr alloys.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.52-56
• /
• 2006

Some of factors affecting photo-conversion efficiency of dye sensitized solar cells (DSCs) are discussed in terms of $TiO_2$ electrodes. The first topic is on the surface modification of $TiO_2$ nano-particles, which is associated with electron traps on the surface of $TiO_2$ nano-particles. The surface is modified with dye molecules under pressurized $CO_2$ atmosphere to increase the surface coverage of $TiO_2$ nano-particles with dye molecules. This increases Jsc because of an increase in the amount of dye molecules and a decrease in the amount of trapping sites on $TiO_2$ nano-particles. In addition, the decrease in the amount of trap sites increases Voc because decreases in Voc are brought about by the recombination of $I_2$ molecules with electrons trapped on the $TiO_2$ surfaces. Selective staining for tandem cells is proposed. The second topic is on the contact between a $SnO_2$/F transparent conductive layer (TCL) and nano-particles. Polishing the TCL surfaces with silica nano-particles increases the contact, resulting in Jsc increases. The third topic is the fabrication of ion-paths in $TiO_2$ layers. Electro-spray coating of $TiO_2$ nano-particles onto TCL is shown to be effective for fabricating ion-paths in $TiO_2$ layers, which increases Jsc.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.156-162
• /
• 2006

Direct fabrication of nano patterns has been studied employing a nano-stereolithography (NSL) process. The needs of nano patterning techniques have been intensively increased for diverse applications for nano/micro-devices; micro-fluidic channels, micro-molds. and other novel micro-objects. For fabrication of high-aspect-ratio (HAR) patterns, a thick spin coating of SU-8 process is generally used in the conventional photolithography, however, additional processes such as pre- and post-baking processes and expansive precise photomasks are inevitably required. In this work, direct fabrication of HAR patterns with a high spatial resolution is tried employing two-photon polymerization in the NSL process. The precision and aspect ratio of patterns can be controlled using process parameters of laser power, exposure time, and numerical aperture of objective lens. It is also feasible to control the aspect ratio of patterns by truncation amounts of patterns, and a layer-by-layer piling up technique is attempted to achieve HAR patterns. Through the fabrication of several patterns using the NSL process, the possibility of effective patterning technique fer various N/MEMS applications has been demonstrated.

• Current Photovoltaic Research
• /
• v.1 no.2
• /
• pp.90-96
• /
• 2013

We report here flexible dye-sensitized solar cells (DSSC) based on Ti-mesh electrodes that show good mechanical flexibility and electrical conductivity. $TiO_2$ nanotube arrays prepared by electrochemical anodizing Ti-mesh substrate were used as photoanode. A Pt-coated Ti-mesh substrate was used as counter electrode. The photoanodes were modified by coating a $TiO_2$ porous layer onto the $TiO_2$ nanotubes in order to increase the specific surface area. To increase the long term stability of the DSSCs, a gel type electrolyte was used instead of a conventional liquid type electrolyte. The DSSC based on $33.2{\mu}m$ long porous $TiO_2$ nanotubes exhibited a better energy conversion efficiency of ~2.33%, which was higher than that of the DSSCs based on non-porous $TiO_2$ nanotubes.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.307-310
• /
• 2009

Nowadays, the usage of high strength steel has been growing in automobile industry mainly as structural parts since for its lightweight and high strength properties the oil crisis happened. Owing to poor formability, complex-shaped high-strength steel components are invariably produced through hot press forming. The high-strength steel sheets are in so me instances used with an Al-Si-coating with a view to prevent scaling of components during hot press forming. How ever, friction and fracture characteristics of Al-Si-coated high-strength steel during hot press forming process have not yet been investigated. In this paper, the formed parts which were formed in hot bending process were investigated by using EDS. SEM and nano indenter in order to analysis the coating layer behavior.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.638-643
• /
• 2013

Laser beam machining (LBM) is fast, contactless and able to machine various materials. So it is used to cut metal, drill holes, weld or pattern the imprinted surface. However, after LBM, there still leave burrs and recast layers around the machined area. In order to remove these unwanted parts, LBM process often uses electrochemical etching (ECE). But, the total thickness of workpiece is reduced because the etching process removes not only burrs and recast layers, but also the entire surface. In this paper, surface coating was performed using enamel after LBM on metal. The recast layer can be selectively removed without decreasing total thickness. Comparing with LBM process only, the surface quality of enamel coating process was better than that. And edge shape was also maintained after ECE.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.1 s.113
• /
• pp.34-44
• /
• 2006

A new composition of paper coating adhesives was prepared by using a nano-filler of an organically-modified montmorillonite (O-MMT). The new O-MMT coating adhesives were applied to the paper, and the properties of coated papers including surface morphology, optical and physical properties, and printing properties were investigated. The use of O-MMT improved the mechanical properties, such as folding endurance, tearing strength, and tensile strength, while the surface smoothness decreased. It decreased especially when the dosage was high enough, approximately above 6 parts. The printing properties such as wet- and dry-pick were enhanced with addition of O-MMT.