• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.222-226
• /
• 2016

The synthesis of pure calcium carbonate nanocrystals was achieved using a simultaneous injection method to produce nano particles of uniform size. These were characterized using scanning electron microscopy and powder X-ray diffraction. The nano particles were needle-shaped aragonite polymorphs, approximately 100-200 nm in length. The aragonite polymorph of calcium carbonate was prepared using aqueous solutions of $CaCl_2$ and $Na_2CO_3$, which were injected simultaneously into double distilled water at $50^{\circ}C$ and then allowed to react for 1.5 h. The resulting whisker-type nano aragonite with high aspect ratio (30) is biocompatible and potentially suitable for applications in light weight plastics, as well as in the medical, pharmaceutical, cosmetic and paint industries.

• Journal of the Korean Ceramic Society
• /
• v.40 no.7
• /
• pp.632-636
• /
• 2003

To prepare the alumina cement free vibrated alumina castable, $\rho$-alumina is employed as a binder material, and nano-sized clay is added to enhance the curing strength and give thixotropic behavior. The rheological behavior of matrix of castable is controlled by investigating the influences of ultrafines, $\rho$-alumina, and nano-sized clay on the viscosity of matrix. The microsilica and ultrafine alumina were added 3 wt% and 4 wt%, respectively to the matrix, which showed that the viscosities tends to be lowest values. The rheological property of the matrix is well established by adding $\rho$-alumina as 8 wt% and clay as 4 wt%. The thixotropic behavior of the $\rho$-alumina bonded castable was appeared by introducing nano-sized clay into the matrix and adjusting the pH near to the PZC of the clay suspension.

• Journal of the Korean Ceramic Society
• /
• v.50 no.4
• /
• pp.275-279
• /
• 2013

The purpose of this study was to prepare calcium phosphate cement [CPC] for use in artificial bone. Nano-crystalline calcium phosphate [CaP] was precipitated at $37^{\circ}C$ using highly active $Ca(OH)_2$ in DI water and an aqueous solution of $H_3PO_4$. From the XRD measurements, the nano-CaP powder was close to apatitic TCP phase and the powders fired at $800^{\circ}C$ showed a critical ${\beta}$-TCP phase. A mixture of one mole $CaCO_3$ and two moles di-calcium phosphate was calcined at $1100^{\circ}C$ to make a reference ${\beta}$-TCP material. The nano-CaP powders were added to the normal ${\beta}$-TCP matrix and fired at $900^{\circ}C$ to make a ${\beta}$-TCP block. The sintered block showed improved mechanical strength, which was caused by the solid state interaction between nano-CaP and normal ${\beta}$-TCP.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2016.05a
• /
• pp.5-5
• /
• 2016

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1027-1046
• /
• 2003

Nanostructured materials can be engineered by the controlled assembly of several suitable nano-objects as the building blocks. While, materials properties are determined by their atomic and molecular constituents and structure, their functionalities emerge when the microstructure of these early ensembles is in the nanometer regime. The properties and functionalities of these ensembles may be different as their size grows from the nano-regime to the micron regime and bulk structures. Nanotechnology, offers a unique possibility to manipulate the properties through the fabrication of materials using the nano-objects as building blocks. Nanotechnology is therefore considered an enabling technology by which existing materials, virtually all man-made materials, can acquire novel properties and functionalities making them suitable for numerous novel applications varying from structural and functional to advanced biomedical in-vivo and in-vitro applications.

• Journal of the Korean Ceramic Society
• /
• v.39 no.4
• /
• pp.336-340
• /
• 2002

Pure and nano-sized $TiO_2$ and $CaTiO_3$ powders were fabricated by a polymeric steric entrapment route and planetary milling process. An ethylene glycol was used as a polymeric carrier for the preparation of organic-inorganic precursors. Titanium isopropoxide and calcium nitrate were dissolved in liquid-type ethylene glycol without any precipitation. At the optimum amount of the polymer, the metal cations were dispersed in solution and a homogeneous polymeric network was formed. The dried precursor ceramic gels were turned to porous powders through calcination process. The porous powders were crystallized at low temperatures and the crystalline powders were planetary milled to nano size.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.852-856
• /
• 2014

$BaTiO_3$ nano powder can be synthesized by hydrate salt method at $120^{\circ}C$ in air. Decreasing the thickness of thick film, the nano dielectric particle is needed in electronic ceramics. However, the synthesis of $BaTiO_3$ nano particle at low temperature in air and their mechanism were not reported enough. And ultrasonic treatment can be tried because of low temperature process in air. Therefore, in this study, the $BaTiO_3$ nano powder was synthesised with the synthesis time and ultrasonic treatment at $120^{\circ}C$ in air. In the synthesis process, the effects of process were evaluated. From the experimental observation, the synthesis mechanism was proposed. The homogeneous $BaTiO_3$ particle was synthesised by KOH salt solution at $120^{\circ}C$ for 1hour. It was conformed that the ultrasonic treatment effected on the increase of synthesis rate. After cutting the salt powder using FIB, $BaTiO_3$ nano particles observed homogeneously in the cross-section of the salt particle.

• Journal of Ceramic Processing Research
• /
• v.19 no.6
• /
• pp.479-482
• /
• 2018

Polystyrene superstructure films show faint rainbow color, and this low color saturation limits its wide application. In this paper, polystyrene superstructure films with single bright blue color were prepared by vertical deposition self-assembly method using polystyrene microspheres with average diameter of $310{\pm}10nm$ as raw material. Polystyrene superstructure films were modified by adding nano-carbon powder, and effect of the amount of nano-carbon powde on color performance was studied. The results showed that without addition of nano-carbon powder, the superstructure films showed a faint rainbow color, while with addition of nano-carbon power, the superstructure films exhibited a single bright blue under the same natural light source. Changing the amount of nano-carbon powder addition could adjust color saturation of the film. With increasing the amount of nano-carbon powder addition from 0.008 wt% to 0.01 wt%, color saturation of the superstructure film increased gradually. Further increasing the amount of nano-carbon powder addition to 0.011wt%, color saturation of the superstructure film didn't increase anymore and tended to get dark.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.560-565
• /
• 2014

Alumina nano-asperites were grown on plate-like alumina particles of which the surface had been covered with a capping agent to control the asperite formation sites on the particles. Utilized alumina source for asperite was nano sized ${\gamma}$-alumina, which was prepared by calcination of $Al(OH)_3$ at $600^{\circ}C$; silica suspension was used as the capping agent. Plate like alumina particles were covered by silica suspension and continuously heat-treated to $900^{\circ}C$ with nano sized ${\gamma}$-alumina, as the source material, under molten-salt atmosphere. Asperite growing site were controlled by the degree of coating of the capping agent; 10-20 nanosize of ${\theta}$-alumina were formed on the particle surface. On the other hand, alumina particles without capping agent were observed to undergo only step-like crystal growth during heat-treatment.

• Journal of the Korean Ceramic Society
• /
• v.50 no.4
• /
• pp.301-307
• /
• 2013

SiC hollow fiber was fabricated by curing, dissolution and sintering of Al-PCS fiber, which was melt spun the polyaluminocarbosilane. Al-PCS fiber was thermally oxidized and dissolved in toluene to remove the unoxidized area, the core of the cured fiber. The wall thickness ($t_{wall}$) of Al-PCS fiber was monotonically increased with an increasing oxidation curing time. The Al-PCS hollow fiber was heat-treated at the temperature between 1200 and $2000^{\circ}C$ to make a SiC hollow fibers having porous structure on the fiber wall. The pore size of the fiber wall was increased with the sintering temperature due to the decomposition of the amorphous $SiC_xO_y$ matrix and the growth of ${\beta}$-SiC in the matrix. At $1400^{\circ}C$, a nano porous wall with a high specific surface area was obtained. However, nano pores grew with the grain growth after the thermal decomposition of the amorphous matrix. This type of SiC hollow fibers are expected to be used as a substrate for a gas separation membrane.