• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.453-458
• /
• 2008

• Journal of Mechanical Science and Technology
• /
• v.18 no.10
• /
• pp.1772-1781
• /
• 2004

The mechanical as well as tribological characteristics of coating films as thin as a few nm become more crucial as applications in micro-systems grow. Especially, the amorphous carbon film has a potential to be used as a protective layer for micro-systems. In this work, quantitative evaluation of nano-indentation, scratching, and wear tests were performed on the 7nm thick amorphous carbon film using an Atomic Force Microscope (AFM). It was shown that AFM-based nano-indentation using a diamond coated tip can be feasibly utilized for mechanical characterization of ultra-thin films. Also, it was found that the critical load where the failure of the carbon film occurred was about 18${\mu}$N by the ramp load scratch test. Finally, the wear experimental results showed that the quantitative wear rate of the carbon film ranged 10$\^$-9/～10$\^$-8/ ㎣ /N cycle. These experimental methods can be effectively utilized for a better understanding the mechanical and tribological characteristics at the nano-scale.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.95-100
• /
• 2019

Nanoindentation has been widely used for evaluating mechanical properties of nano-devices, from MEMS to packaging modules. Residual stress is also estimated from indentation tests, especially the Knoop indenter which is used for the determination of residual stress directionality. According to previous researches, the ratio of the two stress conversion factors of Knoop indentation is a constant at approximately 0.34. However, the ratio is supported by insufficient quantitative analyses, and only a few experimental results with indentation depth variation. Hence, a barrier for in-field application exists. In this research, the ratio of two conversion factors with variation in indentation depth using finite elements method has been attempted at. The magnitudes of each conversion factors were computed at uniaxial stress state from the modelled theoretical Knoop indenter and specimen. A model to estimate two stress conversion factor of the long and short axis of Knoop indenter at various indentation depths is proposed and analyzed.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.342-346
• /
• 2004

Recently there has been a great world-wide interest in developing and characterizing new nano-structured materials. These newly developed materials are often prepared in limited quantities and shapes unsuitable for the extensive mechanical testing. The development of depth sensing indentation methods have introduced the advantage of load and depth measurement during the indentation cycle. In the present work, ZnO thin films are prepared on the Glass, GaAs(100), Si(111), and Si(100) substrates at different temperatures by pulsed laser deposition(PLD) method. Because the potential energy in c-axis is law, the films always shaw c-axis orientation at the optimized conditions in spite of the different substrates. Thin films are investigated by X-ray diffractometer and Nano indentation equipment. From these measurements it is possible to get elastic modulus and hardness of ZnO thin films on all substrates.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.471-474
• /
• 2005

This study investigates the nano/microstructure, the aging response, and the mechanical/tribological properties of the eutectic regions in rheoformed A356 alloy-T5 parts using nano/micro-indentation and mechanical scratching, combined with optical microscopy and atomic force microscope (AFM). Most eutectic Si crystals in the A356 alloy showed a modified morphology as fine-fibers. The loading curve for the eutectic region was more irregular than that of the primary Al region due to the presence of various particles of varying strength. The aging responses of the eutectic regions in the rheoformed A356 alloys aged at $150^{\circ}C$ for different times (0, 2, 4, 8, 10, 16, 24, 36, and 72 h) were investigated. Both Victors hardness $(H_v)$ and indentation $(H_{IT})$ test results showed a similar trend of aging curves, and the peak was obtained at the same aging time of 10 h. A remarkable size-dependence of the tests was found.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.177.1-177.1
• /
• 2015

플라즈마 건식 식각공정은 반도체 공정에 있어 증착 및 세정 공정과 함께 중요한 공정중 하나이다. 기존 연구에서는 높은 식각 속도, 종횡비, 대면적에 대한 균일도 증가를 위하여 플라즈마 이온 밀도의 증가와 전자 온도를 감소시키기 위한 노력을 하고 있으며 플라즈마 식각분석 연구에서는 분광학 분석 기법을 활용하여 플라즈마에 의하여 활성화된 식각 가스와 박막 표면의 반응 메커니즘 연구가 진행 중에 있다. 그러나 지금까지의 플라즈마 식각연구에서는 플라즈마 식각 공정에서 발생되는 박막의 damage에 대한 연구는 전무하다. 본 연구에서는 플라즈마 식각과정에서 발생되는 박막 표면의 damage 연구를 위하여 Nano-indenter에 의한 분석 기법을 제시하였다. Nano-indentation 기법은 박막 표면을 indenter tip으로 직접 인가하여 박막 표면의 기계적 특성을 분석하고 이를 통하여 플라즈마에 의한 박막 표면의 물성 변화를 정량적으로 측정한다. 실험에서 플라즈마 소스는 Adaptively Coupled Plasma (ACP)를 사용하였고 식각 가스로는 HBr 가스를 주로 사용하였으며, 플라즈마 소스 파워는 1000 W로 고정 하였다. 연구 결과에 의하면 식각공정 챔버 내 압력이 5, 10, 15 및 20 mTorr로 증가함에 따라 TEOS SiO2 박막의 강도가 7.76, 8.55, 8.88 및 6.29 GPa로 변화되는 것을 측정하였고 bias power에 따라서도 다르게 측정됨을 확인하였다. 이 결과를 통하여 Nano-indentation 분석 기법을 활용하여 TEOS SiO2 박막의 식각공정의 변화에 따른 강도변화를 측정함으로써 플라즈마에 의한 박막 표면의 damage를 정량적으로 측정 가능함을 확인하였다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.198-202
• /
• 2015

We present a series of simple but novel nanopatterning methodologies inspired by traditional mechanical machining processes involving rolling, pullout, and forging. First, we introduce roll-to-roll nanopatterning, which adapts conventional rolling for continuous nanopatterning. Then, nano-inscribing and nano-channel lithography are demonstrated, whereby seamless nanogratings can be continuously pulled out, as in a pullout process. Finally, we discuss vibrational indentation micro- and nanopatterning. Similarly to the forging/indentation process, this technique employs high-frequency vertical vibration to indent periodic micro/nanogratings onto a horizontally fed substrate. We discuss the basic principles of each process, along with its advantages, disadvantages, and potential applications. Adopting mature and reliable traditional technologies for small-scale machining may allow continuous nanopatterning techniques to cope with scalable and low-cost nanomanufacturing in a more productive and trustworthy way.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.532-538
• /
• 2004

MEMS technology applying to the sensors and micro-electro devices is complete system. These microsystems are made by variable processes. Especially, the mentallization process has very important functions to transfer the power operating the sensor and signal induced from sensor part. But in the structures of MEMS the local stress concentration and deformation are often yielded by an irregular geometrical shape and different constraint. Therefore, this paper studies the effect of supporting type and thickness ratio about thin film of the substrate on the residual stress variation when the thermal loads is applied to the multi-layer thin film fabricated by metallization process. Specimens were made from several materials such as Al, Au and Cu. Then, uniform thermal load was applied, repeatedly. The residual stress was measured by FE Analysis and nano-indentation method using AFM. Generally, the specimen made of Al induced the larger residual stress than that of made of other materials. Specimen made of Cu and Au having the low thermal expansion coefficient induces the minimum residual stress. Similarly, the lowest indentation length was measured by nano-indentation method in the Si/Au/Cu specimen. Particularly, clusters are created in the specimen made of Cu by thermal load and the indentation length became increasingly large by cluster formation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.1-6
• /
• 2018

Recently nano meter size pattern (sub-micro scale) can be machined mechanically using a diamond tool. Many studies have found a 'size effect' which referred to a specific cutting energy increase with the decrease in the uncut chip thickness at micro scale machining. A new analysis method was suggested in order to observe 'size effect' in nano scale machining and to verify the cause of the 'size effect' in this study. The diamond tool was indented to a vertical depth of 1,000nm depth in order to simplify the stress state and the normal force was measured continuously. The tip rounding was measured quantitatively by AFM. Based on the measurements and theoretical analysis, it was verified that the main cause of the 'size effect' in nano scale machining is geometrically necessary dislocations, one of the intrinsic material characteristics. st before tool failure.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.123-126
• /
• 2003

A high strength aluminum alloy bolt (A7050, T7 temper treatment) has been developed by the authors. The bolt has a small grain size in the whole area of the bolt because of the large equivalent strain followed by thermo-mechanical treatment. As the bolt made of A 7050 has a risk of stress corrosion cracking, each grain should be strengthened the grain inside than the grain boundary in order to improve the stress corrosion cracking resistance. It has been confirmed that the nano-indentation hardness at each grain inside increased with the increasing equivalent strain by thermo-mechanical treatment processing.