• 한국수소및신에너지학회논문집
• /
• 제13권4호
• /
• pp.259-269
• /
• 2002

A battery based on the lithium/elemental sulfur redox couple has the advantage of high theoretical specific capacity of 1,675 mAh/g-sulfur. However, Li/S battery has bad cyclic durability at room temperature due to sulfur active material loss resulting from lithium polysulfide dissolution. To improve the cycle life of Li/S battery, PEGDME (Poly(ethylene glycol) dimethyl ether) 500 containing 1M LiTFSI salt which has high viscosity was used as electrolyte to retard the polysulfide dissolution and nano-sized $Mg_{0.6}Ni_{0.4}O$ was added to sulfur cathode as additive to adsorb soluble polysulfide within sulfur cathode. From experimental results, the improvement of the capacity and cycle life of Li/S battery was observed( maximum discharge capacity : 1,185 mAh/g-sulfur, C50/C1 = 85 % ). Through the charge-discharge test, we knew that PEGDME 500 played a role of preventing incomplete charge-discharge $behavior^{1,2)$. And then, in sulfur dissolution analysis and rate capability test, we first confirmed that nano-sized $Mg_{0.6}Ni_{0.4}O$ had polysulfide adsorbing effect and catalytic effect of promoting the Li/S redox reaction. In addition, from BET surface area analysis, we also verified that it played the part of increasing the porosity of sulfur cathode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.74-75
• /
• 2007

We report on the characteristics of organic light-emitting diodes with Al cathode deposited by specially designed twin target sputter(TTS) system. It was found that the Al cathode films grown by TTS system were amorphous structure with nanocrystallines due to low substrate temperature during sputtering process. Effective confinement of high-density plasma between two Al targets lead to low temperature sputtering process on organic layer. Moreover, organic light-emitting diodes with Al cathode deposited by TTS system exhibited low leakage current density of $4{\times}10^{-6}\;mA/cm2$ at -6 V indicating plasma damage due to bombardment of energetic particles such as ions and $\gamma$-electrons was effectively restricted in the ITS system. Sputtering method using ITS system is expected to be applied in organic electronics and flexible displays due to its low temperature and plasma damage free deposition process.

• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.304-307
• /
• 2012

Nano-fibers of LiFePO4 were synthesized from a metal oxide precursor by adopting electrospinning method. After calcination of the above precursor nano-fibers at 800 ℃, LiFePO4 nano-fibers with a diameter of 300 ~ 800 nm, were successfully obtained. Measurement were performed using X-ray diffraction (XRD), fourier transform infrared spectrometer (FT-IR), videoscope, scanning electron microscope (SEM) and atomic force microscope (AFM), respectively, were performed to characterize the properties of the as-prepared materials. The results showed that the crystalline phase and morphology of the fibers were largely influenced the starting materials and electrospinning conditions.

• 전기화학회지
• /
• 제18권3호
• /
• pp.95-101
• /
• 2015

본 논문에서는 차세대 고용량 양극 물질로 각광받고 있는 리튬리치계 산화물의 나노입자의 제조방법에 대해 보고하고 있다. 리튬리치계 산화물은 기존에 사용되고 있는 $LiCoO_2$와 같은 양극물질의 50-80% 이상 높은 용량으로 인해 고용량 이차전지용 양극재료로 기대를 받고 있다. 그러나 이온 및 전자전도성이 좋지 못하여 고율특성이 취약한 단점이 있다. 본 연구에서는 리튬리치계 산화물을 나노입자화 하여 고율특성을 향상시키는데 연구의 초점을 맞추고 있다. 이를 위해 제조공정에서 2가지 계면활성제를 사용, 입자를 분산시켜 나노화 하였다. 나노 입자를 가진 리튬리치 산화물의 전기화학적 특성을 관찰한 결과 상대적으로 우수한 고율특성을 가지고 있음을 확인할 수 있었다.

• 한국세라믹학회지
• /
• 제42권6호
• /
• pp.425-431
• /
• 2005

Line Shaped Solid Oxide Fuel Cell (SOFC) with multilayered structure has been fabricated via direct-writing process. The cell is electrolyte of Ni-YSZ cermet anode, YSZ electrolyte and LSM cathode. They were processed into pastes for the direct writing process. Syringe filled with each electrode and electrolyte paste was loaded into the computer-controlled robe-dispensing machine and the paste was dispensed through cylindrical nozzle of 0.21 mm in diameter under the air pressure of 0.1 tow onto a moving plate with 1.22 mm/s. First of all, the anode paste was dispensed on the PSZ porous substrate, and then the electrolyte paste was dispensed. The anode/electrolyte and the PSZ substrate were co-fired at $1350^{\circ}C$ in air atmosphere for 3 h. The cathode layer was similarly dispensed and sintered at $1200^{\circ}C$ for 1 h. All the electrode/electrolyte lines were visually aligned during the direct writing process. The effective reaction area of fabricated SOFC was $0.03 cm^2$, and the thickness of anode, electrolyte and cathode was 20 $\mu$m, 15 $\mu$m, and 10 $\mu$m, respectively. The single line-shaped SOFC fabricated by direct-writing process exhibited OCV of 0.95 V and maximum power density of $0.35W/cm^2$ at $810^{\circ}C$.

• 한국세라믹학회지
• /
• 제53권4호
• /
• pp.406-410
• /
• 2016

Carbon-coated sodium iron pyrophosphate ($Na_2FeP_2O_7$) was prepared by a simple and low-cost pyro-synthesis route for further use as the cathode for Na-ion batteries. The X-ray diffraction (XRD) pattern of the sample annealed at $650^{\circ}C$ confirmed the pure triclinic phase of $Na_2FeP_2O_7$. Electron microscopy studies revealed a cross linked plate shape morphology of the $Na_2FeP_2O_7$ sample. When tested for application in Na-ion battery, the $Na_2FeP_2O_7$ cathode showed two redox pairs in the potential window of 2.0-4.0 V. The cathode registered initial discharge and charge capacities of 80.85 and 90 mAh/g, respectively, with good cycling performance.

• Journal of Electrochemical Science and Technology
• /
• 제7권2호
• /
• pp.115-131
• /
• 2016

Though battery chemistry and technology had been developed for over a hundred years back, increase in demand for storage energy, in the computer accessories, cell phones, automobile industries for future battery car and uninterrupted power supply, has made, the development of existing and new battery, as an emerging areas of research. With innovation of high energetic inexpensive Nano structure materials, a more energy efficient battery with lower cost can be competitive with the present primary and rechargeable batteries. Materials electrochemistry of electrode materials, their synthesis and testing have been explained in the present paper to find new high efficient battery materials. The paper discusses fundamental of electrochemistry in finding true cell potential, overvoltages, current, specific energy of various combinations of anode-cathode system. It also describes of finding the performance of new electrode materials by various experiments viz. i. Cyclic Voltammetry ii. Chronoamperometry iii. Potentiodynamic Polarization iv. Electrochemical Impedance Spectroscopy (EIS). Research works of different battery materials scientists are discussed for the development of existing battery materials and new nano materials for high energetic electrodes. Problems and prospects of a few promising future batteries are explained.

• 고무기술
• /
• 제6권2호
• /
• pp.91-98
• /
• 2005

Nano-sized cathode materials for high power lithium ion polymer battery are easily and economically prepared using united eutectic self-mixing method without any artificial mixing procedures of reactants and ultra-miniaturization of products. While the micro-sized $LiNi_{0.7}Co_{0.3}O_2$ exhibits the discharge capacities of 167.8 mAh/g at 0.1C and 142.5 mAh/g at 3.0C, those of the nano-sized $LiNi_{0.7}Co_{0.3}O_2$ are 170.8 mAh/g at 0.1C and 159.3 mAh/g at 3.0C. In the case of $LiCoO_2$, the micro-sized $LiCoO_2$ exhibits the discharge capacities of 134.8 mAh/g at 0.1C and 118.6 mAh/g at 5.0C. Differently, the nano-sized $LiCoO_2$ exhibits the discharge capacities of 137.2 mAh/g at 0.1C and 131.7 mAh/g at 5.0C.

• 대한금속재료학회지
• /
• 제49권4호
• /
• pp.342-347
• /
• 2011

We fabricated the silicon nanodots using the low pressure chemical vapor deposition technique to investigate their electron field emission characteristics. Atomic force microscope measurements performed for the silicon nanodot samples having various process parameters, such as, deposition time and deposition pressure, revealed that the silicon nanodots with an average size of 20 nm, height of 5 nm, and density of $1.3\;{\times}\;10^{11}\;cm^{-2}$ were easily formed. Electron field emission measurements were performed with the silicon nanodot layer as the cathode electrode. The current-voltage curves revealed that the threshold electric field was as low as $8.3\;V/{\mu}m$ and the field enhancement factor reached as large as 698, which is compatible with the silicon cathode tips fabricated by other techniques. These electron field emission results point to the possibility of using a silicon-based light source for display devices.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1107-1108
• /
• 2006

The coating of conductive polypyrrole (Ppy) on nonconductive ceramic substrates was performed by polymerization of pyrrole (Py) in an aqueous solution. The Ppy film was characterized by scanning electron microscopy and conductivity measurements. Electrophoretic deposition of bimodal alumina suspension prepared with a phosphate ester was performed using Ppy film as a cathode. Fabrication of alumina ceramics with irregular shapes or complicated patterns were also attempted by sintering the deposits together with the Ppy coated substrates in air.