• Clean Technology
• /
• v.19 no.3
• /
• pp.313-319
• /
• 2013

To produce biodiesel efficiently from fish oil containing 4% free fatty acid, esterification and trans-esterification were carried out with Vietnam catfish oil, which was kindly provided from GS-bio company. Heterogeneous solid acid catalysts such as Amberlyst-15 and Amberlyst BD-20 and sulfuric acid as homogeneous acid catalyst were used for the esterification of free fatty acids in the fish oil. Sulfuric acid showed the highest removal efficiency of free fatty acid and the shortest reaction time among three acid catalysts. The base catalysts for trans-esterification such as KOH, $NaOCH_3$ and NaOH were compared with each other and KOH was determined to be the best transesterification catalyst. Some solid material, which assumed to be saponified product from glycerol and biodiesel, were observed to form in the fish oil biodiesel when using $NaOCH_3$ and NaOH as the transesterification catalyst. The initial acid value of fish oil was proven to have a negative effect on biodiesel conversion. Of the three catalysts, KOH catalyst transesterification was shown to have high content of FAME and the optimal ratio of methanol/oil ratio was identified to be 9:1.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.302-310
• /
• 2001

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless Cu plated layer and polyester (PET) film, the effect of pretreatment conditions such as etching method and mixed catalyst composition, and accelerator was investigated. Compared to NaOH etching medium, PET film was more finely etched by HCl solution, resulting in an improvement in adhesion between Cu layer and PET film. However, there were no significant differences in electromagnetic interference shielding effectiveness as a function of etching medium. The surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$ : SnCl$_2$ from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, the adhesion and the shielding effectiveness of Cu plated PET film were increased. Furthermore, HCl was turned out to be a better accelerator than NaOH in order to enhance the activity of the mixed PdCl$_2$/SnCl$_2$ catalyst, which facilitated the formation of more uniform copper deposit on the PET film.

• Journal of Hydrogen and New Energy
• /
• v.17 no.4
• /
• pp.448-453
• /
• 2006

Porous Co-P catalysts electroplated on Cu in chloride based solution with an addition of $NaH_2PO_2$ and glycine were developed for hydrogen generation from alkaline $NaBH_4$ solution. The microstructures of the Co-P catalysts and their hydrogen generation properties were analyzed as a function of cathodic current density and plating time during the electrodeposition. Amorphous Co-P electrodeposits with porous structure was formed on Cu at cathodic current density of $0.05\;A/cm^2$, and showed very high hydrogen generation rate in alkaline $NaBH_4$ solution due to an increase in the surface area of the catalyst as well as the catalytic activity. The Co-P catalyst, which was obtained at cathodic current density of $0.05\;A/cm^2$ for 5 min, exhibited the best hydrogen generation rate of 2290 ml/min.g-catalyst in 1 wt. % NaOH+10 wt. % $NaBH_4$ solution at $30^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.163-169
• /
• 2020

Synthesis of Fe-Co/meso-HZSM5 catalyst, intended to be applied in Fischer-Tropsch (FT) reaction was investigated. The study emphasized the effect of desilication agents, NaOH and KOH, on the catalyst materials properties. Impregnation composition of active metal (Fe and Co) was also examined. HZSM-5, converted from ammonium ZSM-5 through calcination, was treated with NaOH and KOH for desilication, followed by impregnation with 10% metal loading. Fe composition in the initial mixture was varied at 10-50% from total composition. After impregnation, reduction was applied by flowing hydrogen gas at 400 ℃ for 10 hours. The use of KOH solution induced greater mesoporous volumes; however, it had a detrimental effect on zeolite crystal structure. NaOH solutions, on the other hand, increased mesopore area as high as 100%, indicated from surface area increase from 266.28 m²/g of HZSM-5, to 526.03 m²/g of NaOH-desilicated HZSM-5. In addition, the application of NaOH solution increased pore volume from 0.14 cc/g to 0.486 cc/g. Further, more Fe-Co alloys and less oxide of iron (Fe₂O₃) as well cobalt (Co₃O₄) had been commonly observed in the produced catalysts. The largest Fe-Co alloys could be found in 50Fe-50Co/HZSM-5

• Journal of the Korean Ceramic Society
• /
• v.44 no.6 s.301
• /
• pp.325-330
• /
• 2007

High porous AlO(OH) gel is used in precursor of ceramic material, coating material and porous catalyst. For use of these, not only physiochemical control for particle morphology, pore characteristic and peptization but also studies of synthetic method for preparation of high porous AlO(OH) gel were required. In this study, high porous AlO(OH) gel was prepared through the aging and filtration process of aluminum hydroxides gel precipitated by the hydrolysis reaction of $Na_2CO_3$ solution and $Al_2(SO_4)_3$ and $Na_2SO_4$ mixed solution. In this process, optimum synthetic condition of AlO(OH) gel having excellent pore volume as studying the effect of hydrolysis pH on gel precipitates has been studied. Hydrolysis pH brought about numerous changes on crystal morphology, surface area, pore volume and pore size. Physiochemical properties of gel were investigated as using XRD, TEM, TG/DTA, FT-IR and $N_2$ BET method.

• Resources Recycling
• /
• v.11 no.2
• /
• pp.14-19
• /
• 2002

PVC sheet was treated in O~10M NaOH solutions at $80~150^{\circ}C$ for O~7 hour, in order to study the leaching phenomena of plasticizer. The yield of phthalic acid produced by hydrolysis of DOP was increased greatly with increasing temperature and NaOH concentration by accelerating of alkali catalyst. The yield of phthalic acid was reached ca. 100% in 10M NaOH at $150^{\circ}C$ over 3 hours. Therefore, the plasticizer containing 30% in PVC sheet could be hydrolyzed in alkali solutions before the occurrence of dehydrochlorination. Besides, in the thermal reaction, the pores were produced in the PVCsheet by the hydrolysis of DOP.

• Journal of Hydrogen and New Energy
• /
• v.23 no.6
• /
• pp.654-659
• /
• 2012

The interest in water gas shift (WGS) reaction has grown significantly, as a result of the recent advances in fuel cell technology and the need to develop small-scale fuel processors. Recently, researchers have tried to overcome the disadvantages of the commercial WGS catalysts. As a consequence, supported Pt catalysts have attracted a lot of researchers due to high activity and stability for WGS at low temperatures. In this study, $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts with various Ce/Zr ratio have been applied to WGS at a gas hourly space velocity (GHSV) of $45,515h^{-1}$. According to TPR patterns of $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts, the reducibility increases with decreasing the $ZrO_2$ content. As a result, Cubic structure $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts exhibited higher CO conversion than tetragonal structure $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts. Expecially, Pt-Na/$CeO_2$ exhibited the highest CO conversion as well as 100% selectivity to $CO_2$. Moreover, Pt-Na/$CeO_2$ catalyst showed relatively stable activity with time on stream. The high activity of cubic structure Pt-Na/$CeO_2$ catalyst was correlated to its higher oxygen storage capacity (OSC) of $CeO_2$ and easier reducibility of Pt/$CeO_2$.

• Advances in Energy Research
• /
• v.4 no.3
• /
• pp.189-202
• /
• 2016

This work emphasized optimum production of biodiesel using non-edible Prunus armeniaca (Bitter Apricot) oil via transesterification collected from the high altitude areas of Himachal Pradesh, India. In this study the author produced biodiesel through the process of transesterification by using an alkali catalyst with alcohol (methanol and ethanol), under the varying molar ratio (1:6, 1:9, 1:12), variable catalyst percentage (1% and 2%) and temperature ($70^{\circ}C$, $75^{\circ}C$, $80^{\circ}C$, $85^{\circ}C$). Furthermore, a few strong base catalysts were used that includes sodium hydroxide, potassium hydroxide, sodium metal and freshly prepared sodium methoxide. After screening the catalyst, response surface methodology (RSM) in connection with the central composite design (CCD) was used to statistically evaluate and optimize the biodiesel production operation using NaOH as catalyst. It was found that the production of biodiesel achieved an optimum level biodiesel yield with 97.30% FAME conversion under the following reaction conditions: 1) Methanol/oil molar ratio: 1:6, 2) Reaction time: 3h, 3) Catalyst amount: NaOH 2 wt. %, and 4) Reaction temperature: $85^{\circ}C$. The experimental results showed that the optimum production and conversion of biodiesel through the process of transesterification could be achieved under an optimal set of reaction conditions. The biodiesel obtained showed appropriate fuel properties as specified in ASTM, BIS and En- standards.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.2
• /
• pp.179-185
• /
• 2009

The esterification of the reactants of Jatropha oil and methanol added by propyleneglycol was done using p-TSA catalyst. And then the emulsification of triglyceride and methanol was conduced by 1.0vol% GMS. The emulsified reactants were transesterified at $65^{\circ}C$ using TMAH and mixed catalyst (50wt%-TMAH+50wt%-NaOH) respectively. The esterification conversion at the 1:8 molar ratio of free fatty acid to methanol using 8.0wt% p-TSA was 94.7% within 80min. The overall conversion at the 1:8 molar ratio of mixed fat(50wt% Beef Tallow) to methanol and $65^{\circ}C$ using mixed catalyst was 95.4% The cloud point of Biodiesel decreased with the addition of petroleum diesel.

• Resources Recycling
• /
• v.26 no.6
• /
• pp.91-96
• /
• 2017

Tungsten (W) recovery from tungsten carbide (WC) was researched by alkali melt followed by water leaching. The experiments of alkali melt were carried out with the change of the sort of alkali material, heating temperature, and the heating duration. Water leaching of W was performed in the fixed conditions ($25^{\circ}C$, 2 hr., slurry density: 10 g/L). From the mixture of WC and sodium nitrate ($NaNO_3$) in the molar ratio of 1:2, treated at $400^{\circ}C$ for 6 hours, only 63.3% of W might be leached by water leaching. With the increase of sodium hydroxide (NaOH) as a melting additive, the leachability increased. Finally it reached to 97.8 % with the melted mixture of ($WC:NaNO_3:NaOH$) in the ratio of (1:2:2). This imply that NaOH may play a role as a reaction catalyst by lowering Gibb's free energy for alkali melt reaction for WC.