• Corrosion Science and Technology
• /
• 제20권2호
• /
• pp.77-84
• /
• 2021

This study aims to optimize the DL-EPR test solution for duplex stainless steel S31083 using the Taguchi design. The test solution parameters applied to the Taguchi design are H₂SO₄, NaCl, KSCN concentration, and temperature. In the experimental design, an orthogonal array of 4 levels 4 factor L₁₆(4⁴) was used. Output values for the orthogonal array were used for resolution (degree of sensitization) and selective etch (I_a) values. The optimal test solution conditions were selected by comparing the normalized S/N ratio for the two reaction properties. As a result, the H₂SO₄ and NaCl were identified as the main factors influencing the sensitivity measurement, but the delta statistics showed that the KSCN concentration and temperature had relatively low influence. The optimal condition was identified as 1.5 M H₂SO₄+0.03 M KSCN+1.5M NaCl at 30 ℃. The degree of sensitization presented a tendency to depend on the heat treatment temperature and time in the optimal test solution. This investigation confirmed the possibility of optimizing the experiment solution for the DL-EPR test of stainless steel using the Taguchi technique.

• 한국광물학회지
• /
• 제13권4호
• /
• pp.171-185
• /
• 2000

Siliceous mudstones are embedded on a large scale in the Tertiary formations of Pohang area. Some useful zeolites such as NsP, (Na, TMA)P, analcime and hydroxysodalite were synthesized from the siliceous mudstones by treating with the variety of solution, i.e ., NaOH, NaOH+NaCl, NaOH, NaOH+$NaAlO_2$and NaOH+TMAOH at the low-temperature hydrothermal system ranging 60~12$0^{\circ}C$. Major precursor of zeolites is found as opal-CT in the zeolite-forming reaction. Smectite, which is included in considerable amounts in the mudstone, appears to play a major role of Al-source in the zeolite synthesis. In comparison, chalcedonic quartz and mica are rather insoluble in alkaline solution, and thus, these are observed as major impurities in the reaction products. An addition of $NaAlO_2$to NaOH solution is effective for eliminating these impurities in the reaction procedure, through these are partly dissolved when elevating the reaction temperature, concentration, and time. Phase change from NaP to hydroxysodalite takes place at the NaOH concentrations of 3.0~4.0 M, and the reaction is not sensitive to the temperature shift. NaP is more stable at lower NaOH concentration and higher activity of $Na_{+}$ whereas analcime is sensitive to the temperature change and stable at higher than $100^{\circ}C$ and 2.0~4.0 M in NaOH concentration. For the pure NaP synthesis without any other products, the treatment of mudstones with 1:1 solution of NaOH and $NaAlO _2$ turns out to be quite effective. NaP was successfully synthesized together with analcime at $100^{\circ}C$ as well as lower concentrations of NaOH+NaCl solution. In addition, the organic type, (Na, TMA)P was formed together with smectite in the 1:1 solution of NaOH and TMAOH.

• 한국전기전자재료학회논문지
• /
• 제23권12호
• /
• pp.1002-1006
• /
• 2010

In this study, magnesium (Mg), zinc (Zn) and aluminium (Al) as anode electrode and the solution of NaCl dissolved with 2~20 wt% as electrolytes were used for the metal-air cell. The open circuit voltage, short circuit current and I-V characteristics upon different kinds of anode electrode and electrolyte concentration were investigated. The open circuit voltage, initially about 1.45 V, rises to 1.6 V during the first 10 minutes indicating the necessity of an induction time to activate the catalyst on the air cathode. The short circuit current increases with an increased concentration of NaCl, causes an increase in the conductivity of the electrolyte solution, but the open circuit voltage did not under undergo influence of electrolyte. From NaCl 20 wt% electrolyte, the maximum output power of the magnesium electrode materials was measured with 177mW. It is found that the power characteristics of metal-air cell could be improved by using magnesium electrode materials in the NaCl electrolyte.

• 한국토양비료학회지
• /
• 제16권4호
• /
• pp.318-324
• /
• 1983

이온흡착, 전위차적정, 전기이동법 등을 이용 하여 kaolinite 현탄액의 전기 화학적 성질을 연구하였다. 0.001M 또는 0.1M NaCl 용액중에서 kaolinite로부터 용해되어 나온 알루미늄 이온이 $Na^+$ 및 $Cl^-$과 같이 지시이온으로서 kaolinite 표면에 흡착되는 것을 고려할 때 kaolinite는 pH independent + 및 -전하와 pH dependent + 및 -전하를 모두 가지고 있었다. 증류수와 0.001M NaCl 용액중에서 kaolinite 입자의 전기이동은 전기 이동셀(cell)에서 측정이 시작된 후 시간경과(전기이동 측정시간)에 관계없이 일정한 이동성을 나타냈으나 0.1M NaCl 용액중에서 kaolinite 입자는 등전점 (pH 4.7) 이상에서는 측정시간이 경과함에 따라 전하가 -에서 +로 변화하였다. 즉 최초 10초 동안에는 -전하를 가지며 그 후에는 +전하를 띠면서 전기이동 속도가 단계적으로 증가하게 되는데 약 10분 후에는 일정하게 되었다. 이것은 아마도 제일 바깥쪽 Octahedral layer 표면의 aluminol group의 부분들이 높은 이온 강도의 전해질 용액중에서 분해되어 복잡한 전기이중층(electric double layer)을 이루고 이것이 전기장 내에서 이동할 때 표면으로부터 counter이온들이 점차 떨어져 나가는 과정에서 전하(net charge)의 변화가 생기는 것으로 생각된다.

• 한국식품과학회지
• /
• 제22권3호
• /
• pp.343-349
• /
• 1990

pH를 달리한 수용액 및 농도를 달리한 염류수용액에서 들깨종실의 단백질과 phytate의 용해도를 측정하여 단백질로부터 phytate를 제거할 수 있는 조건을 검토하였다. 들깨종실단백질의 용해도는 pH4.0에서 가장 낮은 9.5%로 등전점을 보였고, 그보다 산성 또는 알칼리성쪽으로 갈수록 증가되었다. 반면에 phytate의 용해도는 pH5.0에서 가장 높았으며 그보다 산성 또는 알칼리성쪽으로 갈수록 감소되었다. NaCl 수용액을 처리하였을 때 단백질의 용해도는 pH $3.0{\sim}4.0$ 범위에서 가장 낮았고 pH 6.0 이상에서는 현저히 증가되었다. Phytate의 용해도는 pH$2.0{\sim}5.0$ 범위에서는 약 90%내외로 높았으나 pH6.0 이상에서는 급격히 감소되었다. $Na_2SO_3$ 수용액처리에서는 단백질 용해도가 $pH2.0{\sim}3.0$ 범위에서 가장 낮았고 phytate의 용해도는 $pH5.0{\sim}6.0$에서 최대치를 보였고, 3%의 경우는 전 pH 구간에 걸쳐서 낮았으나 5%와 7%에서는 전 구간에서 높았다. $CaCl_2$ 수용액처리에서는 단백질 용해도가 3% 수용액에서는 전 pH 구간에서 낮았으나 5%와 7%에서는 $pH5.0{\sim}10.0$에서 높은 값을 보였으며 phytate의 용해도는 $pH2.0{\sim}3.0$ 사이에서 최대값을 나타내고 pH4.0이상에서는 급격히 감소하였다. 이상의 결과에서 3% NaCl 용액을 사용하여 pH9.0에서 단백질을 추출하고 pH4.0에서 침전시켰을 때 단백질 수율이 좋고 phytate 잔존량이 가장 적어, 저(低)phytate 분리단백질을 만드는 가장 좋은 조건이었다..

• Corrosion Science and Technology
• /
• 제8권5호
• /
• pp.193-196
• /
• 2009

For the estimation of uncertainty in potentiodynamic polarization resistance measurement, the type A uncertainty was measured using type 316 stainless steel in an acidified NaCl solution. Sensitivity coefficients were determined for measurand such as scan rate of potential, temperature of solution, concentration of NaCl, concentration of HCl, surface roughness of specimen and flow rate of purging gas. Sensitivity coefficients were large for the measurand such as the scan rate of potential, temperature of solution and roughness of specimen. However, the sensitivity coefficients were not the major factors influencing the combined standard uncertainty of polarization resistance due to the low values of uncertainty in measurements of the measurands. A major influencing factor was the concentration of NaCl. The value of type A uncertainty was 1.1 times the value of type B uncertainty, and the combined standard uncertainty was 10.5 % of the average value of polarization resistance.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.201-206
• /
• 2002

The purpose of this study is to improve the anti-corrosive properties of coated reinforcing bar using polymer cement slurry. Poymer cement slurry are prepared with three types of polymer dispersions and corrosion inhibiting admixture. And tested for corrosion accelerating tests such as immersion in NaCl 10% solution NaCl 10% solution spray, high temperature and pressure steam in condition of 8cycles, carbonation before and after, penetration of NaCl solution. From the test results, it is concluded that the anti-corrosive properties are considerably improved by coating using polymer cement slurry at surface of reinforcing bar. And this trend is marked by adding of corrosion inhibiting admixture. The difference of the anti-corrosive properties is hardly recognized according to types of polymer dispersions. The anti-corrosive properties of coated reinforcing bar using polymer foment slurry are improved to a great extent compared to those of plain reinforcing bar accordiy to increasing content of chloride ion in cement concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.119-120
• /
• 2023

Corrosion of the steel rebar in coastal environment caused huge economical loss of the globe. Therefore, coating on the steel rebar being used to mitigate the corrosion. In the present study, we have applied epoxy coating on arc thermal sprayed Al coating (a dual metal/polymeric coating) vis-à-vis compared with as coated one (Al coating). The corrosion studies were performed in simulated concrete pore solution with 3.5 wt. % NaCl solution. The morphology of the dual epoxy/Al coating is smooth while Al coating shows rankle and defects. Due to defects, Al coating is susceptible to corrosion while dual epoxy/Al coating has performed excellent compared to as coated one at extended period of immersion.

• Corrosion Science and Technology
• /
• 제12권5호
• /
• pp.220-226
• /
• 2013

The uncertainty in statistical noise resistance measurement was evaluated for a type 316 stainless steel in NaCl solutions at room temperature. Sensitivity coefficients were determined for measurands or variables such as NaCl concentration, pH, solution temperature, surface roughness, inert gas flow rate and bias potential amplitude. The coefficients were larger for the variables such as NaCl concentration, pH, inert gas flow rate and solution temperature, and they were the major factors increasing the combined standard uncertainty of noise resistance. However, the contribution to the uncertainty in noise resistance measurement from the above variables was remarkably low compared to that from repeated measurements of noise resistance, and thus, it is difficult to lower the uncertainty in noise resistance measurement significantly by lowering the uncertainties related with NaCl concentration, pH, inert gas flow rate and solution temperature. In addition, the uncertainty in noise resistance measurement was high amounting to 17.3 % of the mean, indicating that the reliability in measurement of noise resistance is low.

• Corrosion Science and Technology
• /
• 제12권1호
• /
• pp.34-39
• /
• 2013

In this study, the effect of niobium addition on the passivation behavior of Ti alloys in NaCl solution was investigated using various electrochemical methods. An ${\alpha}$-phase in Ti alloy was transformed into a ${\beta}$-phase and martensite structure decreased as Nb content increased. The corrosion and passivation current density($+300mV_{SCE}$) decreased as Nb content increased, and thereby a stable passive film was formed on the Ti alloy. Potential of Ti-xNb alloy in the passive region increased, whereas, current density decreased with time from results of potentiostatic and galvanostatic tests. Also, the corrosion morphology showed the smaller pits as Nb content increased. Consequently, Ti alloy contained high Nb content showed a good resistance to pitting corrosion in 0.9% NaCl solution.