• Proceedings of the Membrane Society of Korea Conference
• /
• 1995.04a
• /
• pp.11-15
• /
• 1995

Polysulfone (PS) membranes were prepared by the phase inversion process using water or isopropanol as nonsolvent. The Flory-Huggins theory for a ternary system nonsolvent/solvent/polymer is applied to describe the thermodynamic equilibria of the components. The calculated ternary phase equilibria show that demixing of a PS binary solution with n-methylpyrrolidone (NMP) will be fast in a water coagulation bath and will be delayed in an isopropanol bath. The prepared membranes were characterized by SEM, gas adsorption-desorption measurement, and permeability test. The membrane, which is precipitated by fast demixing in a water bath, has nodular structures in the skin region and includes finger-like cavities in the sublayer. The membrane coagulated by isopropanol has a very dense and thick skin structure, which is formed by delayed demixing. The membrane coagulated by isopropanol showed considerably lower pore volume and surface area compared to that observed with water coagulation method. With dimethylformamide (DMF) as solvent and 2-3 wt% of water, the solution can show the liquid-liquid phase separation due to agglomation of the polymer-lean phase from the homogeneous solution. The membranes, which were coagulated near an equilibrium state, show the large (micron size) round pores in the whole membranes. The pores do not contribute the permeation characteristics.

• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.291-295
• /
• 2018

A conductive additive is prepared by dispersing multi-walled carbon nanotubes (MWCNTs) on Cu powder by mechanical milling and is distributed in epoxy to enhance its electrical conductivity. During milling, the MWCNTs are dispersed and partially embedded on the surface of the Cu powder to provide electrically conductive pathways within the epoxy-based composite. The degree of dispersion of the MWCNTs is controlled by varying the milling medium and the milling time. The MWCNTs are found to be more homogeneously dispersed when solvents (particularly, non-polar solvent, i.e., NMP) are used. MWCNTs gradually disperse on the surface of Cu powder because of the plastic deformation of the ductile Cu powder. However, long-time milling is found to destroy the molecular structure of MWCNTs, instead of effectively dispersing the MWCNTs more uniformly. Thus, the epoxy composite film fabricated in this study exhibits a higher electrical conductivity than 1.1 S/cm.

• Journal of Korea Association of Health Promotion
• /
• v.2 no.2
• /
• pp.215-230
• /
• 2004

Along with a development of medical technology, a variety of tests, such as laboratory tests, x-ray and endoscopies are being used in health screening tests. As the tests determine the quality of health screening, test items and methods should be carefully selected. This study was to get hold of the test items of major health screening programs in Korea. Most of the health screening programmes focused upon detection of risk factors and diagnosis of life-style related diseases(diabetes, hypertension, cardiovascular diseases, hypercholesterolemia, overweight, drinking, smoking, cerebrovascular diseases, osteoporosis) ,cancers(stomach, cervix, lung, breast, liver, colon, prostate, ovary, pancreas, thyroid, esophagus), infectious diseases (hepatitis, tuberculosis, sexually-transmitted diseases, parasites),chronic obstructive respiratory diseases, chronic renal diseases(bacteriuria, hematuria, proteinuria), anemia, glaucoma, hearing loss, Alzheimer disease, stress, early Psychiatric diseases. The health screening tests were basic physical examination, basic laboratory tests(CBC, urinalysis, liver function tests, lipid tests, glucose, HbAlc, uric acid, electrolytes, serological tests(HBsAg, HBs-Ab, HCV-Ab, HIV-Ab, VDRL) EKG, x-ray(chest PA, CT), endoscopy (gastroscopy, colonoscopy) , sonography(abdormen, thyroid, pelvis, breast) , cytology(cervix) ,bone density, tumor markers(NMP22, alpha-FP, CEA, CA-19-9, CA12S, PSA) and eye tests. Advanced technologies, like CT, PET, MIRI, MIRI/Angio, molecular testings) were widely usedin hospital health screening programmes. In summary, a variety of were utilized by stages or programmes, however a few subjects. tests were utilized in health screening in Korea. Those tests according to sex and age in most of health screening program used tests to excess disregarding health screening subject.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.153-153
• /
• 2008

Practical application of single-walled carbon nanotubes (SWCNTs) qualified as a promising material has been limited by either poor dispersion or their insolubility in aqueous or organic media due to formation of bundling by relatively high surface energy. Thus, major attention to overcome this issue has been paid at surface modification of CNTs by functionalization, but this introduces defects to the sidewall of CNTs, consequently perturbing the inherent electronic and optical properties. Therefore, using surfactants is a general approach to disperse SWCNTs with lower damages by which bundled nanotubes could be dispersed up to the level of individuals or small bundles. Here, we have investigated various surfactants for their efficiency in dissolving purified SWCNTs produced by arc discharge in deionized water. To compare the surfactants respectively, we have determined the least amount of each surfactant to suspend the nanotubes under optimized experimental conditions(CNT amount, sonication power, and centrifugation speed, etc.) set on the basis of the most common surfactant (sodium dodecyl sulfate, SDS) and discussed the qualitative and quantitative characterization of SWCNT dispersions by UV-Vis absorption spectroscopy. Quantitative aspect about nanotube dispersion was that in particular N-methyl-2-pyrrolidone (NMP) and sodium dodecylbenzene sulfonate (NaDDBS) were found to be effective in dispersing individual tubes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.620-623
• /
• 2013

The carbon nanotube / poly-vinylidene fluoride (CNT/PVDF) composite films for the nano-generator devices were fabricated by spray coating method using the CNT/PVDF solution, which was prepared by adding PVDF pellets into the CNT dispersed N-Methyl-2-pyrroli-done (NMP) solution. The flexible CNT/PVDF composite films were investigated by the scanning electron microscopy, which revealed that the CNTs were uniformly dispersed in the PVDF matrix and thickness of the films was approximately $20{\mu}m$. Fourier transform infra-red spectra were used to investigate crystal structure of the as-spray-coated CNT/PVDF films, and we found that they revealed extremely large portion of the ${\beta}$ phase PVDF. The capacitance of the CNT/PVDF films increased by adding CNTs into the PVDF matrix, and finally saturated. However, the resistance didn't show any saturation effect in the CNT concentration range of 0~4 wt%. Finally, the resulting nano-generator devices revealed reasonable current output after given mechanical stress.

• Elastomers and Composites
• /
• v.53 no.3
• /
• pp.141-149
• /
• 2018

A series of aromatic poly(o-hydroxyamide)s (PHAs) were synthesized by the direct polycondensation reaction of 4,4′-(2,3-quinoxalinedioxy) dibenzoic acid and/or 4,4′-(2,3-pyridinedioxy) dibenzoic acid with bis(o-aminophenol) including 2,2-bis-(amino-4-hydroxyphenyl)hexafluoropropane. The PHAs exhibited inherent viscosities in the range of 0.17-0.35 dL/g at $35^{\circ}C$ in a DMAc solution. These polymers showed low inherent viscosities and yielded brittle films. All the PHAs showed excellent solubility in aprotic solvents such as DMAc, DMSO, NMP, and DMF at room temperature and in less polar solvents such as pyridine and THF. However, all the PBOs were only partially soluble in $H_2SO_4$. The PBOs exhibited 10% weight loss at temperatures in the range of $537-551^{\circ}C$. The maximum weight loss temperature increased with an increase in the content of the quinoxaline-containing monomer. The residue of the PBOs showed a weight loss of 45.8-56.7% at $900^{\circ}C$ in a nitrogen atmosphere.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.2
• /
• pp.72-78
• /
• 2014

In a cold chain, the refrigerator is also employed for defrosting, by using an electric heater, which consumes 15% of the power for the system operation. In this study, the condensation heat of the refrigerant was suggested as the heat source of defrosting heat, instead of that from an electric defrost heater. The heat for defrosting was stored to a phase change material (PCM, NMP : $52^{\circ}C$) in thermal storage, and was periodically supplied to the evaporator by a circulation loop of brine. As a result, a defrost time by the PCM was obtained that was less than or equal to that by the electric heater. Moreover, power consumption during defrosting was saved by up to 99% of that of the electric heater.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.107-114
• /
• 2003

This study investigated the effect of 2-methoxy ethanol (2-Me) non-solvent as additive included in casting solution. Macroporous polymer membranes were prepared by using polyethersufone (PES)/N-methyl-2-pyrrolidone (NMP)/2-Me casting solution and water coagulant. The phase separation co-process of the vapor-induced phase separation (VIPS) and liquid-induced phase separation (LIPS) were used by means of membrane preparation method. The pore size and pore size distribution were controlled with additive (non-solvent), and measured with Automated Perm Porometer. By increasing additive (non-solvent) in the casting solution, the membranes produced changed from finger structure to sponge structure. That is due to the different diffusion rates. At slow diffusion process, sponge-like structure was formed and at fast diffusion process, finger-like structure was formed. Also relative humidity, evaporation time, temperature of casting solution and coagulation bath etc. had effects on the pore size distribution and the porosity of the membrane.

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.54-60
• /
• 1997

The electrical and electromagnetic shielding properties have been investigated in polyaniline free standing films with different degrees of elongation cast from N-methyl 2-pyrrolidone(NMP) solution and camphorsulfonic acid(HCSA) doped polyaniline film. The degree of crystallinity of the crosslinked films increased with increasing the draw ratio. For the case of the oriented films doped with hydrochloric acid, we have the values of conductivities up to 173 S/cm. It is considered that the physical micro-crystalline crosslinking domains act as nucleation sites for the increase of relative crystallinity during stretching. We have obtained the value of conductivity 210 S/cm in the HCSA doped polyaniline film cast from the solvent of m-cresol, which is higher than that of the crosslinking oriented films. The electromagnetic shielding efficiency of HCSA doped polyaniline film obtained 37-41 dB in the frequency range of 10MHz-1GHlz, which is higher than that of the crosslinking oriented films. The higher value of electromagnetic shielding efficiency of HCSA doped polyaniline film suggests strong possibility of electromagnetic shielding material.

• The Journal of Korea Robotics Society
• /
• v.11 no.2
• /
• pp.92-99
• /
• 2016

An electro-hydraulic actuator (EHA) is widely used in industrial motion systems and the increasing bandwidth of EHA position control is important issue. The model-inverse feedforward controller is known to extend the bandwidth of system. When the system has non-minimum phase (NMP) zeros, direct model inversion makes system unstable. To overcome this problem, an approximate model-inverse method is used. A representative approximate model inversion method is zero phase error tracking control (ZPETC). However, if zeros locate right half plane of z-plane, the approximate inverse model amplifies the high-frequency response. In this paper, to solve the problem of ZPETC, an adaptive model-inverse control is proposed. The adaptive algorithm updates feedforward term in real-time. The effectiveness of the proposed adaptive model-inverse position control strategy is verified by comparison with typical proportional-integral (PI) control and feedforward control by experiments. As a result, the proposed adaptive controller extends the bandwidth of EHA position control.