• 한국산업보건학회지
• /
• 제6권1호
• /
• pp.17-27
• /
• 1996

This study was designed to survey exposure levels of formaldehyde among workplaces in some plywood industries and to compare three sampling methods including the impinger method(IM, NIOSH method No. 3500), the solid sorbent tube method(SS, NIOSH method No. 2541), and the passive bubbler monitor method(PB, SKC). The survey was conducted in seven particle board manufacturing factories, two resin manufacturing factories and two plywood manufacturing factories in Incheon area during the period from March 6 to April 20, 1995. The workplaces included were the hot/cold press, the roller/spreader, the soaking/drying, and the reaction/mixing areas. The results were as follows; 1. The average(GM, GSD) concentrations of formaldehyde by sampling methods were 0.11(4.43) ppm by IM, 0.27(2.03) ppm by SS, and 0.29(2.04) ppm by PB, respectively. The concentrations by 1M method were statistically very significantly lower than those of SS and PB methods, particularly at low air borne concentrations of formaldehyde (p<0.001). 2. The area average concentrations of formaldehyde by workplaces measured with PB bubblers were 0.23(2.08) ppm from the press, 0.23(1.77) ppm from the spreader, 0.24(1.51) ppm from the soaking, and 0.46(1.96) ppm from the reaction areas, respectively. The personal average concentrations of formaldehyde by workplaces measured with PB bubblers were 0.30(1.77) ppm from the press, 0.33(1.54) ppm from the spreader, 0.36(1.46) ppm from the soaking, and 0.84(1.19) ppm from the reaction areas, respectively. 3. No statistically significant differences of formaldehyde concentrations among workplaces except the reaction area(p<0.001) were found. 4. Formaldehyde concentrations from personal samples were higher than those of from area sam pies in all workplaces studied. But no statistically significant differences of formaldehyde concentrations both area and personal samples were found. In conclusion, this study found that although formaldehyde concentrations in some plywood industries in Incheon area were below the regulatory limit of 1 ppm, they were over the limits recommended by NIOSH and ACGIH. This study also suggests that the impinger method may underestimate true formaldehyde concentrations. It implies that there will be more workplaces not meeting current regulatory limit if either the solid sorbent or passive bubbler methods were used instead of the impinger method. It is suggested that passive monitors will be a reasonable alternative for area and personal sampling of formaldehyde if the accuracy and validity of passive monitors be verified before use.

• 반도체디스플레이기술학회지
• /
• 제21권2호
• /
• pp.117-122
• /
• 2022

This paper proposes a method for evaluating the work of manufacturing workers using MediaPipe as a risk factor for musculoskeletal diseases. Recently, musculoskeletal disorders (MSDs) caused by repeated working attitudes in industrial sites have emerged as one of the biggest problems in the industrial health field while increasing public interest. The Korea Occupational Safety and Health Agency presents tools such as NIOSH Lifting Equations (NIOSH), OWAS (Ovako Working-posture Analysis System), Rapid Upper Limb Assessment (RULA), and Rapid Entertainment Assessment (REBA) as ways to quantitatively calculate the risk of musculoskeletal diseases that can occur due to workers' repeated working attitudes. To compensate for these shortcomings, the system proposed in this study obtains the position of the joint by estimating the posture of the worker using the posture estimation learning model of MediaPipe. The position of the joint is calculated using inverse kinetics to obtain an angle and substitute it into the REBA equation to calculate the load level of the working posture. The calculated result was compared to the expert's image-based REBA evaluation result, and if there was a result with a large error, feedback was conducted with the expert again.

• 지역사회간호학회지
• /
• 제15권2호
• /
• pp.289-297
• /
• 2004

Purpose: This study was conducted to determine factors affecting workers' physiological somatic complain using the Job Stress Model proposed by the National Institute for Occupational Safety and Health (NIOSH). Method: Data were collected from the 1st to the 30th of December 1999. The subjects were 2.123 workers employed at 155 work sites. Collected date were analyzed through SAS/PC program. Result: According to individual characteristics, younger and women groups showed significantly higher physiological somatic complaint than elder men groups. By work condition, groups with higher physiological somatic complaint included workers of irregular shift work. Dark lighting, improper temperature in winter, improper ventilation, inappropriate humidity, unpleasant work environment and crowded work place were significantly related with physiological somatic complaint. By work-related factor, physiological somatic complaint was high in those with higher variance in work load, quantitative work load, role conflict, job burden, role ambiguity and future ambiguity. On the other hand, physiological somatic complaint was low in those with little underutilization of ability. As for the relationships between physiological somatic complaint and non-work related factors, physiological somatic complaint was high in workers who had a side job, were bringing up infants alone, cleaned the house alone, cared for the elderly and disabled persons, were studying, were volunteering at another organization, and were spending 5-10 hours in religious activities per week. Physiological somatic complain was in significantly negative correlations with overall social support, supervisory support and family support, but in significantly positive correlations with co-worker support. Conclusion: The main predictors of physiological somatic complain were gender, shift work pattern, overtime work, ventilation, role ambiguity, role conflict, future ambiguity, job control, variance in work load, overall social support, worker with side job, worker who cleans the house alone, worker who is studying. These predictors explained 19.10% of the total variance of physiological somatic complain.

• 한국산업보건학회지
• /
• 제9권2호
• /
• pp.135-144
• /
• 1999

The purposes of this study were to survey types of pretreatment methods adopted by industrial hygiene laboratories in Korea for extracting heavy metals in welding fume samples and to compare performances of two pretreatment methods, the acid extraction and the microwave digestion, in extracting heavy metals contained in the real workplace samples from various welding jobs including arc, argon, and carbon dioxide. A total of 25 analytical chemists in the industrial hygiene laboratories participating the quality control program directed by the Korea Industrial Safety Corporation were interviewed by telephone. For the purpose of comparing performance of extracting heavy metals from real workplace samples, a total of 53 welders from 21 workplaces located in Anyang, Uiwang, and Kunpo areas were sampled from the period of March 22, 1999 to April 20, 1999. It was found that the most frequently adopted method for samples from the quality control program was the acid extraction method(40%) followed by the NIOSH 7300 method(36%). The NIOSH method, however, was the dominant method(36%) for samples from workplace followed by the acid extraction method(28%). In this study, two extraction methods, the acid extraction and the microwave digestion, were compared in terms of recovery rate, accuracy, and precision for both manganese and chromium. Both methods produced comparable results for the samples prepared for the quality control program. In contrast, concentrations of two heavy metals determined from real workplace samples pretreated with the microwave digestion method were statis tically significantly higher, manganese(166%) and chromium (200%), than those of utilizing the acid extraction method. These findings were consistent regardless of types of welding techniques used. The results of this study clearly show the importance of verifying the analytical performances of extraction methods for heavy metals not only for the samples from the quality control program but also from the real world samples collected from welding jobs.

• 한국산업보건학회지
• /
• 제11권1호
• /
• pp.48-55
• /
• 2001

The purpose of this study was to evaluate the analytical accuracy and precision of microwave oven digestion/atomi absorption spectrophotometry (AAS) for analyzing airborne chromium collected on mixed cellulose ester membrane (M filter from the work environment, and to compare the accuracy and the precision with those of the National Institute for Occupational Safety and Health (NIOSH) Method #7024 hot plate digestion/AAS method. For this study, field air sample pairs were collected from a electroplating process, and spiked samples in a laboratory were prepared and using these samples. Two digestion methods were comp; and evaluated in terms of recovery rate and bias as indices of accuracy and coefficient of variation as a index of precision. The results and conclusions are as follows. In spiked samples, the accuracies (% mean recoveries) of hot plate/AAS and microwave oven/AAS method were 97.19%, 97.1%, respectively, and the precisions (pooled respectively, and the precisions (pooled coefficient of variance, $CV_{pooled}$) 6.93% and 3.88%, respectively. The biases of hot plate ani microwave oven methods were 4.56 - 14.7% and 2.22 - 7.42% respectively. There was no statistically significant difference between hot plate and microwave oven methods recovery rates of spiked samples (p>0,05). Also, no statistically significant difference was shown among the concentrations of air samples determined by two method (p>0.05). In conclusion, microwave oven/AAS method h excellent accuracy and precision, and advantages such as time-saving and simple procedure in comparison with the classical NIOSH method. Therefore, this method can be use widely to analyze airborne chromium collected on MCE filter from the work environments.

• 한국산업보건학회지
• /
• 제26권3호
• /
• pp.307-316
• /
• 2016

Objectives: In general, NIOSH method 5506 is most widely used for the occupational exposure measurement of PAHs, but 2-4 ring PAHs have poor desorption efficiency, especially for a filter. The purpose of this study was to determine a method to increase the desorption efficiency of 16-PAHs using an ultrasonic extraction procedure. Methods: Test samples prepared spiked XAD-2 tubes and PTFE filters in the range of $0.01-1.0{\mu}g/mL$ for desorption efficiency study. Four different extraction solvents, acetonitrile, acetone, tetrahydrofuran and dichloromethane, were tested in order to select the most suitable solvent for the extraction of the 16 PAHs. The addition of dimethyl sulfoxide and sonication time were considered in order to determine the method with the highest extraction efficiency. All samples were made in three sets and analysis was replicated seven times by HPLC. Results: Acetonitrile and acetone were the optimized as an extraction solvent and desorption efficiency of 2-ring PAHs such as naphthalene, acenaphthylene were increased 3~19% with dimethyl sulfoxide for XAD-2. Acetone was the best extraction solvent for PTFE filter and the desorption efficiency was increased 3~13% for 2- to 4-ring PAHs. The optimum sonication time was 60 minutes and desorption efficiency increased with extraction time. Conclusions: As a result, the best extraction solvent was acetone with dimethyl sulfoxide for ultrasonic extraction procedure and the desorption efficiency of this method was better than NIOSH 5506's. This study could be applied as a method for occupational exposure measurement of PAHs.

• 한국산업보건학회지
• /
• 제11권3호
• /
• pp.241-248
• /
• 2001

The main factors of breakthrough are known to sampling time, flow rate, concentration of the sample, temperature, humidity, and the physical characteristics of the solid sorbent tube. However, no study has been reported the effect of temperature and sampling volume on the breakthrough of acharcoal tube during vinyl chloride monomer (VCM) sampling. The objective of this study is to suggest the optimal sampling condition during VCM sampling based on National Institute for Occupational Safety and Health (NIOSH) method. To evaluate adequate sampling volume for VCM without breakthrough, volume of 1, 2, 3, 4, and 5 L each from VCM of 1, 5, 10, 15, and 20ppm at flow rate of 0.05 L/min were sampled in $22^{\circ}C$ and $40^{\circ}C$. At $22^{\circ}C$, in the case of 1, 5, 10, and 15ppm, VCM was adsorbed completely in first section of charcoal tube regardless of sampling volume. But in 20ppm, detection rates are 99.56% in first section and 0.44% in second section. At $40^{\circ}C$ of 1ppm, VCM was adsorbed completely in first section. In 10, 15, and 20ppm, detection rates of second, third, and forth sections were decreased significantly by reduction of sampling volume. In determination of breakthrough based on NIOSH method, no breakthrough was occurred in 20ppm at $22^{\circ}C$. At $40^{\circ}C$, breakthrough was occurred in 10, 15, and 20ppm when sampling volume was 5L. Although no breakthrough was occurred when sampling volume was 3L. Finally, in environment of temperature around $22^{\circ}C$, breakthrough may not occurred up to 20ppm during sampling for VCM. During sampling for VCM in environment of temperature around $40^{\circ}C$, no breakthrough occurred in 1-5ppm and 10-20ppm when sampling volume is 5L and 3L respectively. This result suggests that the sampling volume should be considered when VCM sampling under hot conditions (> $22^{\circ}C$) by the NIOSH method No. 1007.

• 한국산업보건학회지
• /
• 제25권1호
• /
• pp.89-94
• /
• 2015

Objectives: The objective of this study was to determine characteristics of workers' exposures to airborne total and hexavalent chromium by job title in electroplating processes. Methods: Total Cr was determined through a modified method based on NIOSH Method 7024. Airborne hexavalent Cr, Cr(VI), was sampled and extracted according to NIOSH Method 7600 and analyzed at 520 nm using an ion chromatograph/visible detector. Results: The geometric mean(GM) of total Cr concentrations from all factories was $11.2{\mu}g/m^3$(GSD=4.9). The GM of Cr(VI) concentrations from all factories was $2.84{\mu}g/m$ (GSD=5.2), and the concentrations among factories were significantly different (p<0.05). The Cr(VI) levels were lower than total Cr levels. Total Cr exposure levels were highest among buffing workers ($21.6{\mu}g/m^3$), but Cr(VI) levels were highest among plating workers($4.15{\mu}g/m^3$). The concentrations of Cr(VI) and total Cr from plating tasks was highly correlated(r=0.91). Conclusions: In the electroplating industry, plating workers were mainly exposed to Cr(VI), but others were not. Oxidation-reduction states of Cr and job titles should be considered in the exposure or risk assessments of chrome electroplating factories.

• 한국직업건강간호학회지
• /
• 제15권1호
• /
• pp.14-29
• /
• 2006

Purpose: The purposes of this study were to survey the extent of pain and discomfort in the musculoskeletal system among visiting housekeepers, above all concerning neck, shoulder, back, wrist, knee, and arm pain and to find possible relations between symptoms and various working conditions. Method: A questionnaire was answered by 174 woman visiting housekeepers living in Kyeonggi-do and Seoul from December 1, 2003 to February 30, 2004. The symptoms of musculoskeletal system were coded by the pain index which illustrates the extent of the symptoms, and analyzed in view of NIOSH guideline and Kim, et. al.'s notion. Result: 1. As to the complaint rate of subjective musculoskeletal symptoms by body region, the figure was the highest for shoulder with 78.2%, followed by back with 66.7%, knee 53.6%, neck 56.3%, wrist 40.2%, and arm 29.2%, respectively. The logistic analysis showed shoulder pain and arm pain have no relation with working and health conditions, and back pain was significantly related to current health condition. In same way, knee pain and wrist pain were found to be mainly related to marital status. 2. Following the NIOSH guideline, the positive rate of subjective musculoskeletal symptoms was found out in following order: shoulder 69.5%, back 59.2%, knee 54%, neck 46%, wrist 32.8%, and arm 25.3%. To investigate the main cause of each disease, the symptoms were classified by pain index, where the value of more than 3 comes to the NIOSH case, and analyzed in term of complaint rate using discrete logistical method : shoulder pain was highly related to the housekeeping time after work, back pain was to current health condition and the heavy weight carrying and neck, wrist, arm pain were commonly related to the ordinary health condition. For knee pain, working speed was a main cause. 3. In view of Kim et. al.'s standard, where the pain index is over 7, the positive rate was showed in order slightly different from previous analyses : shoulder 33.3%. knee 29.9%, back 28.2%, neck 17.2%, wrist 17.2%, and 16.7%. From the logistical analysis, insufficient rest was shown as the main cause of shoulder, back, arm and wrist pain. For neck pain, ordinary health condition was mainly related. In case of knee pain, any apparent relation is not found. Conclusion: According to the logistic regression analysis of musculoskeletal system, there was strong suggestion that the less insufficient physical rest, the more significant disorder complaint. This means that the most musculoskeletal symptom among the visiting housekeepers can be prevented and cured by sufficient physical resting.

• 한국산업보건학회지
• /
• 제24권4호
• /
• pp.484-491
• /
• 2014

Objectives: An image processing program for asbestos fibers analyzing the gradient components and partial linearity was developed in order to accurately segment fibers. The objectives were to increase the accuracy of counting through the formulation of the size and shape of fibers and to guarantee robust fiber detection in noisy backgrounds. Methods: We utilized samples mixed with sand and sepiolite, which has a similar structure to asbestos. Sample concentrations of 0.01%, 0.05%, 0.1%, 0.5%, 1%, 2%, and 3%(w/w) were prepared. The sand used was homogenized after being sieved to less than $180{\mu}m$. Airborne samples were collected on MCE filters by utilizing a personal pump with 2 L/min flow rate for 30 minutes. We used the NIOSH 7400 method for pre-treating and counting the fibers on the filters. The results of the NIOSH 7400 method were compared with those of the image processing program. Results: The performance of the developed algorithm, when compared with the target images acquired by PCM, showed that the detection rate was on average 88.67%. The main causes of non-detection were missing fibers with a low degree of contrast and overlapping of faint and thin fibers. Also, some duplicate countings occurred for fibers with breaks in the middle due to overlapping particles. Conclusions: An image detection algorithm that could increase the accuracy of fiber counting was developed by considering the direction of the edge to extract images of fibers. It showed comparable results to PCM analysis and could be used to count fibers through real-time tracking by modeling a branch point to graph. This algorithm can be utilized to measure the concentrations of asbestos in real-time if a suitable optical design is developed.