• Korean Journal of Optics and Photonics
• /
• v.8 no.5
• /
• pp.357-361
• /
• 1997

We report the operation of a self-starting phase conjugate laser(PCL) oscillator which compensates intracavity phase distortion. The self-starting PCL in the population inverted Nd:YAG gain media produced an output energy of 200 mJ in a 20 ns single-longitudinal-mode pulse at 10Hz. And it showed well-defined Gaussian spatial profile.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.146-153
• /
• 1993

Thd specimens were melited in high frequency induction furnace. The samples for measurements were prepared by machining cylinder of 9.5mm diameter and 15mm height. These samples were then hot-pressed according to strain rate ( .epsilon. ). These samples were decanned and cut out, and subsequently heat treated at 1000 .deg. C for 4hours. These were investigated for the change of microstructure, domain pattern, X-ray diffraction and magnetic properties. The stress distributions in the specimens during compressing process were calculated by a finite element method program(SPID). The calculated stresses were effective stress( .sigma. $_{eff}$), compressive direction stress( .sigma. $_{z}$), and shear stress( .tau. $_{rz}$ ). These stresses were compared with the experimental data.a.a.

• Journal of Welding and Joining
• /
• v.19 no.3
• /
• pp.317-324
• /
• 2001

This study deals with high power Nd:YAG laser welding of thin steels for small pressure vessels. Full penetration welding at the overlap joint was performed so as to assure sufficient weld strength. Results showed that mid-depth weld size reduced drastically with increasing the travel speed. Position of focus had little effect on the bead formation even though short focal system was used. However, the shape factor and the bead width had closely related with the position of focus. Based on the microstructural inspection, acceptable weld was obtained when the overlap clearance was controlled up to 20% of the base metal thickness. In the case that the joint contained more clearance than the critical value, both the tensile shear strength and the tear strength were reduced. Results also demonstrated that shielding gases were proved to play a key role as far as the bead formation characteristics was taken into consideration. Blowing dry air through 5mm in diameter nozzle produced narrower bead cross-section than that of argon or nitrogen shielding.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1900-1902
• /
• 1997

In order to obtain various waveforms of current pulse applied at the flashlamp, we have fabricated a Pulsed Nd:YAG laser by PFN with multiple-mesh formed LC network. we have obtained various waveforms of current pulse by adjusting the values of L and C, compared these waveforms of current pulse with laser beam, and then analyzed the laser output energy. We have got relations for $E_{TH}$ and $E_L$ at each mesh which supplies energy with flashlamp and found that output of Pulsed Nd:YAG Laser for 2-mesh, 5-mesh coincided with computer's simulation, PSPICE.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.1
• /
• pp.1-4
• /
• 2008

The growth of composite-structured Nd:$GdVO_4$ single crystal rods by the double die EFG method is reported. Two crucibles are combined with an outer and inner die for ascending of different melt. The composite-structured Nd:$GdVO_4$ single crystal rods with a length of 50 mm and an outer diameter of 5 mm including of inner Nd-doped core region with diameter 3 mm were grown successfully. Nd distribution in the, radial direction has graded profile from result of EPMA. Absorption coefficient in the core region at 808 nm was $42cm^{-1}$. Finally, we demonstrated the laser oscillation using our composite crystal and 2-W output was obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.481-488
• /
• 2004

Laser chemical vapor deposition can be used as a new approach for a rapid prototyping technique. The purpose of the study is to fabricate several 3-dimensional objects that are relatively simple as well as to find the characteristics of SiC rod growth that is the first step in developing a new rapid prototyping technique with laser chemical vapor deposition. In the study, SiC rods were generated with varying precursor pressure for 5 minutes. Deposition rates with varying precursor pressure, shapes of rods, surface roughness and component organization were investigated, in particular. Finally, several simple objects like a branch or a propeller were successfully fabricated using laser chemical vapor deposition.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.606-610
• /
• 2006

We investigated the output characteristics of Nd:YAG lasers at wavelength of 1444 nm, which were pumped by 450 Xe-flashlamp, 700 torr Xe-flashlamp and 700 torr Kr-flashlamp. With a Xe-flashlamp of 700 torr of gas pressure, the pulse energy of 0.738 J was obtained with repetition rate of 9.16 Hz and pumping pulse width of 400 ms. In case pumping pulse width of 5 ms and repetition rate of 1 Hz, 700 torr Kr-flashlamp showed the highest pulse energy of 1.44 J.

• Journal of Powder Materials
• /
• v.19 no.1
• /
• pp.1-5
• /
• 2012

In order to improve the remanence of (Nd, Dy)-Fe-B sintered magnets, we investigated the influence of compaction conditions such as packing density, applied field and green density on the magnetic properties. While the remanence decreased with increasing the packing density and green density, it increased with the increase of the applied field. In addition, XRD analysis revealed that the remanence was enhanced as the degree of powder alignment was improved. The green density was more influential on the remanence than the packing density and applied field.

• Proceedings of the Optical Society of Korea Conference
• /
• 1997.08a
• /
• pp.85-85
• /
• 1997

Czochralski 방법에 의해 육성된 Nd:YAG 단결정으로부터 CW mode의 1064nm laser를 발진시켰다. 육성된 단결정은 직경 50mm, 길이 120mm 이었으며, Nd 이온 농도는 O.2~0.9at% 이었다. 육성된 단결정 boule로 부터 결정학적 결함부위인 core 및 facet가 없는 양질의 단결정 부위를 Twyman-Green interferometer로 선빌하였다. 추출핀 부위는 절단, 가공, 연마공정 및 코팅 공정을 통해 직경 6.35mm, 길이 lOOmm의 laser rod를 제작하였다. 절단은 core drill, 또는 원통 연삭기를 사용하여 rod 형태로 가공하였으며, 상$\cdot$하면 polishing은 평행도 10", 직각도 5', 평활도 $\lambda$/10 수준까지 실험실에서 자체 가공하여 일반적인 laser 발진용 rod의 spec.을 만족시킬 수 있었다.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.20-25
• /
• 1989

The nonlinear, time dependent photon transport equations of Frantz and Nodvik, which describe the amplification of an optical pulse in an active medium, are modified to a simpler equation which describes only the amplification of energy. with this equation, the output energy of the high power YLF(Nd3+)-Phosphate Glass(Nd3+) Laser System is calculated. When the stored energy density Est is 0.10J/㎤, 0.16J/㎤, 0.228J/㎤, and 0.50J/㎤, and with the assumption of uniform population inversion density, the final output energy of this laser system is 5.38J, 176J, 317J, and 283J, respectively. The gain saturation causes distortion of the output beam. This phenomenon is described in detail at the first three rod amplifier systems in the case of E=0.228J/㎤. The peak current and decay time constant of the flashlamps, which are used to obtain population inversion in the active medium, are investigated. The flashlamp driving circuit which has optimum operational performance should have {{{{ SQRT { LC} }} time about 100$\mu$sec.