• 한국정밀공학회지
• /
• 제29권4호
• /
• pp.395-408
• /
• 2012

An experimental investigation with 2.8kW Nd:YAG laser system was carried out to study the effects of different laser process parameters on the microstructure and hardness of STD11. The optical lens with the elliptical profile are designed to obtain a wide surface hardening area with uniform hardness. The Laser beam is allowed to scan on the surface of the work piece varying the power (1600, 1800 and 1900kW) and traverse speed (200, 400, 600, 800 and 1000mm/min) at three different F-numbers of lens. After laser surface treatment three zones, In the microstructure have been observed : melted zone(decarburization), heat affected zone(martensite), and the substrate.

• Journal of Welding and Joining
• /
• 제18권3호
• /
• pp.83-88
• /
• 2000

Laser cladding processing allows rapid transfer of heat to the material being processed with minimum conduction into base metal, resulting in low total heat input. The effects of Nd:YAG laser cladding with wire feeding on the mechanical properties of Inconel alloy were investigated. inconel alloy is used as the material of nuclear steam generator tubing because of its mechanical properties and corrosion resistance properties. The device for Nd:YAG laser cladding with wire feeding was designed. It consists of the wire feeding system, the wire cladding system and the shielding gas system which prevents the clad layer from being oxidized. Experimental as results indicated that the wire feeding direction and position were important for laser cladding with wire feeding. The wire feeding speed should be adapted according to cladding speed for good shaping of clad layer. The effect of heat on the HAZ size can be limited and the growth of grain size of HAZ size was not serious. The hardness of clad layer and heat affected zone increased with increasing of cladding speed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.286-291
• /
• 2004

The objective of this research work is to investigate the influence of process parameters, such as power of laser, travel speed of laser and material thickness, on roughness and striation of the cut surface for the case of cutting of CSP 1N sheet using high power Nd:YAG laser with continuous wave(CW). In order to find the practical cutting region and the relationship between process parameters on the roughness and the striation, several laser cutting experiments are carried out. From the results of experiments, the allowable cutting region and an optimal cutting speed for each cutting condition have been obtained to improve the quality of the cut surface. In addition, it has been shown that the surface roughness is related to the number of striation and depth of valley of the cut surface.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2107-2109
• /
• 2000

A pulsed Nd:YAG laser is used widely for materials processing and medical instrument. It's very important to control the laser energy density in those fields using a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this paper, the alternating charge and discharge system was designed to adjust a pulse repetition rate This system is controlled by microprocessor and allows to replace an expensive condenser for high frequency to cheap one for low frequency. In addition, The microcontroller monitors the flow of cooling water, short circuit. and miss firing and so on. We designed Nd:YAG laser firmware with smart microcontroller, and want to explain general matters about the firmware from now.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.162-165
• /
• 2005

The objective of this research work is to investigate into the three-dimensional temperature distribution using quasi steady-state heat transfer analysis fur the case of the laser cutting of CSP 1N sheet using high power CW Nd:YAG laser. The laser heat source is assumed as a volumetric heat source with a gaussian heat distribution in a plane. Through the comparison of the results of analyses with those of the experiments, the optimal finite element model is obtained. Finally, characteristics of the three-dimensional heat transfer and temperature distribution have been estimated by the optimal finite element model.

• 한국광학회지
• /
• 제20권5호
• /
• pp.276-280
• /
• 2009

Cr:YAG 결정을 포화흡수체로 사용하여 수동형 Q-스위치시킨 다이오드 레이저 여기 Nd:$YVO_4$ 레이저를 제작하였다. Cr:YAG 결정의 한 면에 여기 빛 파장(808 nm)에 대해 고반사 코팅을 한 후, Nd:$YVO_4$ 결정과 접촉시켜 공진기를 구성하였다. Cr:YAG의 한 면에 여기 다이오드 레이저를 반사시키는 코팅을 입혀 공진기의 광변환 효율을 높임과 동시에, 여기빔에 의한 포화흡수체의 표백현상을 방지하여 안정된 출력이 나오게 하였다. 레이저 이득 매질 및 포화흡수체의 온도는 열전 냉각기와 냉각수를 사용하여 안정화 시켰다. 온도안정화를 시킨 상태에서 발진되는 펄스의 첨두 출력 요동(peak to peak)은 4%였다. 다이오드 레이저의 출력이 1 W일 때, 출력 펄스의 반복률은 평균 9 KHz 였으며, 최소 펄스폭은 7.11 ns, 최고 출력은 16.27 mW였다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.25-26
• /
• 2005

This study suggested the occurrence source of weld-defects and its solution methods in a welding of Electrolyte injection hole by pulsed Nd:YAG laser. In experiment, the ramp down was used in order that solidification crack was removed. Furthermore, shrinkage stress and heat input were reduced by changing of weld trajectory and defocused distance. As a results of a experiment, a sound weld bead shape and crack-free weld bead can be obtained.

• 한국자기학회지
• /
• 제15권6호
• /
• pp.320-324
• /
• 2005

[ $3\%$ ] 규소강판에 대한 코어손실 특성은 규소장판에 포함된 실리콘 함유량, 불순물의 농도, 투자율, 자구의 구조 등에 의존한다. 자구 미세화는 고 투자율을 갖는 규소강판의 코어손실을 감소시키는 좋은 방법이다. 본 연구에서는 펄스형 Nd : YAG 레이저를 규소강판에 조사함으로써 규소강판의 자구를 미세화 하여 코어손실을 최소화 할 수 있는 최적조건을 분석하였다. 조사된 레이저빔의 spot 크기는 $100{\mu}m$, 펄스 당 에너지는 10${\~}$35mJ, 스크라이빙 줄 간격은 5mm로 결정하였으며 펄스폭이 30ns인 Nd:YAG 레이저를 사용하여 규소강판의 코어손실을 최대 $17\%$까지 개선하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.213-215
• /
• 2006

Application for laser welding have increased steadily in recent years due to its benefits such as high speed, high productivity and high density energy heat source. In this article these advantages of the laser welding has been considered for Nd:YAG laser stitch welding as a substitute for spot welding of lightweight car body plates. Optimized parameters for Nd:YAG laser stitch welding have been determined comparing the economical and mechanical characteristics to match with the currently used spot welding characteristics.

• 대한기계학회논문집A
• /
• 제31권8호
• /
• pp.839-846
• /
• 2007

Nd:YAG pulse laser fillet welding of stainless steel plate was simulated to find welding condition by using commercial finite element code MARC. Full model of AISI 304 stainless steel plate was considered and user subroutines were applied to boundary condition for the heat transfer. Material properties such as conductivity, specific heat, mass density and latent heat were given as a function of temperature. As results, Three dimensional heat source model for pulse laser beam conditions of fillet welding has been designed by the comparison between the finite element analysis results and experimental data on AISI 304 stainless steel plate. Nd:YAG laser welding for AISI 304 stainless steel was successfully simulated and it should be useful to determine optimal welding condition.