• Korean Journal of Materials Research
• /
• v.29 no.10
• /
• pp.586-591
• /
• 2019

This study describes the doping effect of $Yb_2O_3$ on microstructure, electrical and dielectric properties of $ZnO-V_2O_5-MnO_2-Nb_2O_5$ (ZVMN) ceramic semiconductors sintered at a temperature as low as $900^{\circ}C$. As the doping content of $Yb_2O_3$ increases, the ceramic density slightly increases from 5.50 to $5.54g/cm^3$; also, the average ZnO grain size is in the range of $5.3-5.6{\mu}m$. The switching voltage increases from 4,874 to 5,494 V/cm when the doping content of $Yb_2O_3$ is less than 0.1 mol%, whereas further doping decreases this value. The ZVMN ceramic semiconductors doped with 0.1 mol% $Yb_2O_3$ reveal an excellent nonohmic coefficient as high as 70. The donor density of ZnO gain increases in the range of $2.46-7.41{\times}10^{17}cm^{-3}$ with increasing doping content of $Yb_2O_3$ and the potential barrier height and surface state density at the grain boundaries exhibits a maximum value (1.25 eV) at 0.1 mol%. The dielectric constant (at 1 kHz) decreases from 592.7 to 501.4 until the doping content of $Yb_2O_3$ reaches 0.1 mol%, whereas further doping increases it. The value of $tan{\delta}$ increases from 0.209 to 0.268 with the doping content of $Yb_2O_3$.

• The Korean Journal of Mycology
• /
• v.41 no.4
• /
• pp.268-273
• /
• 2013

Bacillus amyloliquefaciens M27 was isolated from the cotton-waste compost for cultivation of oyster mushroom (Pleurotus ostreatus). B. amyloliquefaciens M27 is a biocontrol agent with antagonistic activities against a wide range of fungal pathogens. The aim of this work was to evaluate the possibility of exploiting antagonistic bacteria, B. amyloliquefaciens M27, in the biological control of the cucumber powdery mildew fungus, Podosphaera fusca. In greenhouse tests, the isolate was found to be very effective to control powdery mildew on cucumber leaves showing 4.0% diseased area, whereas diseased area in the control was 80.5%. The filtrate of the isolate cultured on MH and LB media were more effective for control of the disease than those cultured on TSB, NB, and KB media. When two, five, ten, 20, 50 and 100-fold diluted culture broth of isolate on LB media were treated, disease areas were 0%, 0%, 0%, 1.3%, 3.1% and 5.0%, respectively, whereas diseased area in the control was 60.0%. The filtrate of the isolate cultured on LB media was treated to cucumber plants on July, October and December just before the outbreak of the powdery mildew occurred. When 10-fold diluted filtrate of the isolate was treated, control efficacy was 88.9~98.9% in the treated seasons. The results showed that the culture filtrate of B. amyloliquefaciens M27 was very effective to control powdery mildew of cucumber.

• Journal of Life Science
• /
• v.15 no.1 s.68
• /
• pp.55-60
• /
• 2005

The murine dopamine receptor regulating factor (DRRF) gene is transcribed from a TATA-less promoter that has several putative Sp1 binding sites. The present investigation identifies functional transcription factors that modulate the expression of this gene, In the $D_2-expressing$ NB41A3 cells, Spl potently activates transcription from the DRRF promoter in pCAT-DRRF-1153/+17, but DRRF effectively inhibits it. Deletion of the 31 bp fragment between -1153 and -1122 decreased transcription down to about $60\%$. This fragment contains a functional API binding site. In addition, deletion of the 129 bp region between -901 and -772 further decreased transcription. The latter region has a functional AP2 binding site. Using a DRRF_AP1 (bases -1153 to -1121) probe, a specific retarded band was observed, and the unlabeled AP1 consensus competitor could effectively compete away this retarded band. In addition, using a DRRF_AP2 (bases -873 to -846), a specific retarded band was observed, and the unlabeled AP2 consensus competitor could effectively compete away this retarded band. The present observations suggest that Spl and DRRF regulate the DRRF promoter and that both API and AP2 also modulate this gene.

• Journal of the Korea Convergence Society
• /
• v.13 no.3
• /
• pp.33-41
• /
• 2022

In this article, we proposed to predict natural gas (NG) leakage levels through feature selection based on a factor analysis (FA) of the integrating the Korean Meteorological Agency data and natural gas leakage data for considering complex factors. The paper has been divided into three modules. First, we filled missing data based on the linear interpolation method on the integrated data set, and selected essential features using FA with OrdinalEncoder (OE)-based normalization. The dataset is labeled by K-means clustering. The final module uses four algorithms, K-nearest neighbors (KNN), decision tree (DT), random forest (RF), Naive Bayes (NB), to predict gas leakage levels. The proposed method is evaluated by the accuracy, area under the ROC curve (AUC), and mean standard error (MSE). The test results indicate that the OrdinalEncoder-Factor analysis (OE-F)-based classification method has improved successfully. Moreover, OE-F-based KNN (OE-F-KNN) showed the best performance by giving 95.20% accuracy, an AUC of 96.13%, and an MSE of 0.031.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.3
• /
• pp.41-45
• /
• 2007

This paper presents transport current non-uniformity in a joint for superconducting multistage cable-in-conduit conductor (CICC) and relaxation in the CICC. The joint is considered to have a current loop linked to an external magnetic field so that it becomes an emf voltage source. It is numerically analyzed using an electrical transmission line model. The inductive current in a resistive joint is compared to that of a non-resistive joint when the ramping field is applied vertically to the joints. Regarding the parameter values of the model. a full scale $Nb_3Sn$ CICC and a strand-to-strand (STS) joint for the toroidal field magnet of the KSTAR (Korea Superconducting Tokamak Advanced Research) device are referenced to. It is found that the resistive joint prevents the current from rising too much and enhances decaying the current when the ramping stops. The 'flattop' current is found to be proportional to the ramp rate of the field (dB/dt). The relaxation length, which is defined as the length within which the maximum induced current falls by 1/e. is found to saturate within 0.27m.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.1
• /
• pp.13-19
• /
• 2009

A 440MHz wireless and passive surface acoustic wave (SAW) based chemical sensor was developed on a $41^{\circ}YX\;LiNbO_3$ piezoelectric substrate for simultaneous measurement of $CO_2$ gas and relative humidity (RH) using a reflective delay line pattern as the sensor element. The reflective delay line is composed of an interdigital transducer (IDT) and several shorted grating reflectors. A Teflon AF 2400 and a hydrophilic $SiO_2$ layer were used as $CO_2$ and water vapor sensitive films. The coupling of mode (COM) modeling was conducted to determine optimal device parameters prior to fabrication. According to simulation results, the device was fabricated and then wirelessly measured using the network analyzer. The measured reflective coefficient $S_{11}$ in the time domain showed high signal/noise (S/N) ratio, small signal attenuation, and few spurious peaks. In the $CO_2$ and humidity testing, high sensitivity ($2^{\circ}/ppm$ for $CO_2$ detection and $7.45^{\circ}/%$RH for humidity sensing), good linearity and repeatability were observed in the $CO_2$ concentration ranges of $75{\sim}375ppm$ and humidity levels of $20{\sim}80%$RH. Temperature and humidity compensations were also investigated during the sensitivity evaluation process.

• The Korean Journal of Mycology
• /
• v.41 no.4
• /
• pp.261-267
• /
• 2013

In order to select antagonists for biological control of downy mildew of cucumber, 126 bacteria were isolated from cucumber plants collected from several locations in Korea. Among them, Five isolates were selected as potential biocontrol agents of cucumber downy mildew using a leaf disc bioassay method. In preventive and curative effect tests, the isolate CC110 was found to be effective to control downy mildew on cucumber showing diseased area by 0% whereas that of control was 15.0~18.0%. A bacterium isolate CC110 was identified as Bacillus amyloliquefaciens subsp. plantarum based on phylogenetic analysis using gyrB gene sequence. The culture liquid of isolate CC110 in TSB media were more effective for the control of the disease than those cultured in LB, NB, and KB media in leaf disk bioassay. when undiluted liquid, two-fold, five-fold diluted culture broth, and undiluted liquid, two-fold, five-fold diluted filtrate of isolate CC110 in TSB media were treated, diseased area of cucumber powdery mildew were 0%, 3.0%, 8.0%, 0%, 4.0% and 7.0%, respectively, whereas diseased area in the control was 21.0%. In the cucumber seedling tests, when the culture broth of isolate CC110 in TSB media was treated, diseased area were 35.0%, whereas that of control was 82.0%. When B. amyloliquefaciens CC110 was treated four times at five-day interval in the vinylhouse test, the control effect of cucumber downy mildew was higher than that treated three at seven-day interval.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.68-69
• /
• 2005

Low temperature ($\leq900^{\circ}C$) sintering piezoelectric ceramics $0.01Pb(Mg_{1/2}W_{1/2})O_3$-0.41Pb$(Ni_{1/3}Nb_{2/3})O_3-0.35PbTiO_3-0.23PbZrO_3+0.1wt%Y_2O_3+xwt%ZnO$ $(0{\leq}x{\leq}2.5)$ have been developed and investigated. The electromechanical coupling coefficient ($k_p$), piezoelectric constant ($d_{33}$), and mechanical quality factor ($Q_m$) have been measured to characterize the piezoelectric materials system. When 2.0 wt% ZnO is added, the properties of the system, $d_{33}$ = 559 pC/N, $k_p$ = 55.0 % and $Q_m$ = 73.4 are obtained which are very suitable for piezoelectric actuators. A bending mode multilayer actuator has been also developed using the materials which size is $27(L)\times9(W)\times1.07(t)mm^3$. The actuators are fabricated by multilayer ceramic (MLC) process and consist of24 layers and each layer thickness is $35{\mu}m$. At this time, the displacement of actuator was $100{\mu}m$ at 28V.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.3 s.36
• /
• pp.267-274
• /
• 2005

This paper presents the fabrication of surface acoustic wave (SAW)-based pressure sensor for long-term stable mechanical compression force measurement. SAW pressure sensor has many attractive features for practical pressure measurement: no battery requirement, wireless pressure detection especially at hazardous environments, and easy other functionality integrations such as temperature, humidity, and RFID. A $41^{\circ}$ YX $LiNbO_3$ piezoelectric substrate was used because of its high SAW propagation velocity and large values of electromechanical coupling factors $K^2$. A silicon substrate with $\~200{\mu}m$ deep cavity was bonded to the diaphragm with epoxy, in which gold was covered all over the inner cavity in order to confine electromagnetic energy inside the sensor, and provide good isolation of the device from its environment. The reflection coefficient $S_{11}$ was measured using network analyzer. High S/N ratio, sharp reflected peaks, and clear separation between the peaks were observed. As a mechanical compression force was applied to the diaphragm from top with extremely sharp object, the diaphragm was bended, resulting in the phase shifts of the reflected peaks. The phase shifts were modulated depending on the amount of applied mechanical compression force. The measured $S_{11}$ results showed a good agreement with simulated results obtained from equivalent admittance circuit modeling.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.8
• /
• pp.858-868
• /
• 1992

0.085Ba(LaS11/2TNbS11/2T)OS13T-0.915Pb(ZrS1yTTiS11-yT)OS13T (0.45$\leq$y$\leq$0.65) transparent electrooptic ceramics were fabricated by two-stage sintering method. The structural, ferroelectric and electrooptic properties were investigated varying composition and second sintering time. Also the possibility of application to electrooptic device was studied. If we increase the PbZrOS13T contents, dielectric constants were increased and Curie temperature was decreased. In the composition of 0.55[mol] PbZrOS13T, electromechanical coupling factor and piezoelectric charge constant were the highest values of 43[%] and 173x10S0-12T[C/N], respectively. Mechanical quality factors were decreased with the increasing PbZrOS13T contents. Light transmittance was increased with wavelength when measured from 300[nm] to 900[nm], and with PbZrOS13T contents in the range of 0.50[mol]-0.65[mol], and had the highest value of 67[%] in the composition of 0.65[mol] PbZrOS13T. From the results of ferroelectric hysteresis loop and transmitted light intensity with electric field, the specimens with compositions of 0.65,0.60,0.55[mol] PbZrOS13T were applicable to electrooptic memory device and those with compositions of 0.50,0.45[mol] PbZrOS13T were applicable to linear electrooptic device.