• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.47-50
• /
• 2010

Various thicknesses of Al-doped ZnO (AZO) films were deposited on glass substrate using pulsed dc magnetron sputtering with a cylindrical target designed for large-area high-speed deposition. The structural, electrical, and optical properties of the films of various thicknesses were characterized. All deposited AZO films have (0002) preferred orientation with the c-axis perpendicular to the substrate. Crystal quality and surface morphology of the films changed according to the film thickness. The samples with higher surface roughness exhibited lower Hall mobility. Analysis of the measured data of the optical band gap and the carrier concentration revealed that there were no changes for all the film thicknesses. The optical transmittances were more than 85% regardless of film thickness within the visible wavelength region. The lowest resistivity, $4.13\times10^{-4}\Omega{\cdot}cm^{-1}$ was found in 750 nm films with an electron mobility $(\mu)$ of $10.6 cm^2V^{-1} s^{-1}$ and a carrier concentration (n) of $1.42\times10^{21} cm^{-3}$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1057-1061
• /
• 2007

In this study, we investigated the properties of ZnO thin films prepared by layer-by-layer method in RF magnetron sputtering system using AlAs and ZnO targets. Effects of $H_2O_2$ dip prior to thermal treatment were studied as well. Either n-type or p-type films were observed in our study depending on the annealing conditions. It thus indicates the feasibility of arbitrarily modifying the conductivity type. At the same time, it also implies the thermal instabilities of the film properties. Property measurements after stressing the films up to 144 hours showed that thermal variations of properties nay be suppressed by pre-treatment in 30% $H_2O_2$ for 1 min.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.705-711
• /
• 2000

A thin film oxide semiconductor micro gas sensor array which shows only 60 mW of power consumption at an operating temperature of $300^{\circ}C$ has been fabricated using microfabrication and micromachining techniques. Excellent thermal insulation of the membrane is achieved by the use of a double-layer structure of $0.1\mum\; thick\; Si_3N_4 \;and\; 1 \mum$ thick phosphosilicate glass (PSG) prepared by low-pressure chemical-vapor deposition (LPCVD) and atmospheric-pressure chemical-vapor deposition (APCVD), respectively. The sensor array consists of such thin film oxide semiconductor sensing materials as 1 wt.% Pd-doped $SnO_2,\; 6 wt.% A1_2O_3-doped\; ZnO,\; WO_3$/ and ZnO. Baseline resistances of the four sensing materials were found to be stable after the aging for three days at $300^{\circ}C$. The thin film oxide semiconductor micro gas sensor array exhibited resistance changes usable for subsequent data processing upon exposure to various gases and the sensitivity strongly depended on the sensing layer materials.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.2
• /
• pp.315-322
• /
• 2002

A thin film oxide semiconductor micro gas sensor array which shows only 60㎽ of power consumption at an operating temperature of 30$0^{\circ}C$ has been fabricated using microfabrication and rnicrornachining techniques. Excellent thermal insulation of the membrane is achieved by the use of a double la! or structure of 0.1${\mu}{\textrm}{m}$ thick Si$_3$N$_4$ and 1${\mu}{\textrm}{m}$ thick phosphosilicate glass(PSG) prepared by low pressure chemical vapor deposition(LPCVD) and atmospheric－pressure chemical-vapor deposition(APCVD), respectively. The sensor way consists of such thin film oxide semiconductor sensing materials as 1wt.％ Pd-doped SnO$_2$, 6wt.% AI$_2$O$_3$-doped ZnO, WO$_3$ and ZnO. The thin film oxide semiconductor micro gas sensor array exhibited resistance changes usable for subsequent data processing upon exposure to various gases and the sensitivity strongly depended on the sensing layer materials. Heater Part of the sensor structure has been modified in order to improve the process yield of the sensor, and as a result of modified heater structure improved process yield has been achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.7
• /
• pp.567-571
• /
• 2009

Polycrystalline ZnO and Ga doped ZnO (GZO) films are deposited on glass substrate by RF magnetron sputtering at room temperature. The characteristics of ZnO and GZO films are investigated with X-ray diffraction measurement, UV-VIS-NIR spectrophotometer $(250{\sim}1200nm)$ and hall measurement. The post-growth thermal treatment of these films is carried out in N2 ambient at $500^{\circ}C$ for 30 min and an hour. ZnO and GZO films have different changing behavior of structural and optical properties by annealing. To use transparent conductive films for solar cell, films should have not only high transmittance but also good electrical property. Although as deposited GZO films have electrical properties than ZnO films, GZO films have not good transmittance properties. Consequently, we succeed that the high transmittance of GZO films is improved by annealing process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.984-989
• /
• 2012

We have investigated the structural, electrical and optical properties of Ga-doped ZnO (GZO) thin films prepared by RF magnetron sputtering with laboratory-made ZnO targets containing 1, 3, 5, 7 wt% of $Ga_2O_3$ powder as a doping source. The GZO thin films show the typical crystallographic orientation with c-axis regardless of $Ga_2O_3$ content in the targets. The $3,000{\AA}$ thick GZO thin films with the lowest resistivity of $7{\times}10^{-4}{\Omega}{\cdot}cm$ are obtained by using the GZO ($Ga_2O_3$= 5 wt%) target. Optical transmittance of all films shows higher than 80% at the visible region. The optical energy band gap for GZO films increases as the carrier concentration ($n_e$) in the film increases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.145-146
• /
• 2006

The most Important research topic in the development of ZnO LED and LD is the production of p-type ZnO thin film that has minimal stress with outstanding stoichiometric ratio. In this study, Phosphorus diffused into the undoped ZnO thin films using the ampoule-tube method for the production of p-type znO thin films. The undoped ZnO thin films were deposited by RF magnetron sputtering system on $GaAs_{0.6}P_{0.4}$/GaP and Si wafers. 4N Phosphorus (P) was diffused into the undoped ZnO thin films in ampoule-tube which was performed and $630^{\circ}C$ during 3hr. We found the diffusion condition of the conductive ZnO films which had p-type properties with the highest mobility of above 532 $cm^2$/Vs compared with other studies PL spectra measured at 10K for the purpose of analyzing optical properties of p-type ZnO thin film showed strong PL intensity in the UV emission band around 365nm ~ 415nm and 365nm ~ 385nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.391-391
• /
• 2010

The stability enhancement of Znic oxide thin film transistor deposited by PLD-DBD has been reported here using the bias temperature stress test. Znic oxide (ZnO) thin films were deposited on $SiO_2$/Si (100) by pulsed laser deposition method with and without dielectric barrier discharge (DBD) method. The DBD is the efficient method to adopt the nitrogen ions into the thin films. The TFT characteristics of ZnO TFTs with and without Nirogen (N) doping show similar results with $I_{on/off}$ of $10^5{\sim}10^6$. However. the bias temperature stress (BTS) test of N-doped ZnO TFT with DBD shows higher stability than that of ZnO TFT.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2001.07a
• /
• pp.66-66
• /
• 2001

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.21-26
• /
• 1995

Highly sensitive and mechanically stable gas sensors have been fabricated using the microfabrication and micromaching techniques. The sensing material used to detect the offensive trimethylarnine ((CH$_{3}$)$_{3}$N) gas is 6 wt% $Al_{2}$O$_{3}$-doped, 1000.angs.-thick ZnO deposited by r. f. magnetron sputtering. The optimum operating temperature of the sensor is 350.deg.C and the corresponding heater power is about 85mW. Excellent thermal insulation is achieved by the use of a double-layer structure of 0.2.mu.m -thick silicon nitride and 1.4.mu.m-thick phosphosilicate glass(PSG) prepared by low pressure chemical vapor deposition(LPCVD) and atmospheric pressure chemical vapor deposition(APCVD), respectively. The sensors are mechanically stable enough to endure at least 43, 200 heat cycles between room temperature and 350.deg. C.