• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2326-2333
• /
• 2000

Creep tests for type 316L(N) stainless steel were carried out using constant-load creep machines at 55$0^{\circ}C$, 575$^{\circ}C$ and $600^{\circ}C$. Material constants necessary to predict creep rupture time were obtained from the experimental creep data. And the applicability of Monkman-Grant(M-G) and modified M-G relationships was discussed. The log-log plot of M-G relationship between the rupture time($t_r$,) and the minimum creep rate ($ $\varepsilon$ _m$) was dependent on test temperatures. The slope of m was 1,05 at 55$0^{\circ}C$ and m was 1.30 at $600^{\circ}C$. On the other hand, the log-log plot of modified M-G relationship between $t_r/$\varepsilon$_r$, and $ $\varepsilon$ _m$ was independent on stresses and temperatures. That is, the slope of m＇ was approximately 1.35 in all the data. Thus, modified M-G relationship for creep life prediction could be utilized more reasonably than that of M-G relationship for type 316L(N) stainless steel. It was analyzed that the constant slopes regardless of temperatures or applied stresses in the modified relationship were due to an intergranular fracture grown by wedge-type cavities.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.1
• /
• pp.58-67
• /
• 2016

The corrosion behavior of duplex stainless steel AISI 2205 was investigated in ethylene glycol-water mixture in the presence of 50 W/V % LiBr at different concentrations and different temperatures. Cyclic polarization, impedance measurements and Mott-Schottky analysis were used to study the corrosion behavior the semi conductive properties of the passive films. The results showed that with increasing in the ethylene glycol concentration to 10 V/V%, the corrosion rate of the steel alloy substrate increased. In higher concentrations of ethylene glycol, corrosion current of steel decreased. The results of scanning electron microscopy of electrode surface confirmed the electrochemical tests. Electrochemical experiment showed that duplex steel was stable for pitting corrosion in this environment. The increase in the ethylene glycol concentration led to increasing the susceptibility to pitting corrosion. The corrosion current increased as the temperature rise and also pitting potentials and repassivation potentials shifted towards the less positive values as the temperature increased. According to Mott-Schottky analysis, passive films of stainless steel at the different temperatures showed both n-type and p-type semiconductor behavior in different potential.

• Korean Journal of Materials Research
• /
• v.17 no.12
• /
• pp.654-659
• /
• 2007

Austenite precipitation behavior was studied with solidification rates and alloying contents, N and Cr, in duplex stainless steels by directional solidification. Directional solidification experiments were carried out with solidification rates, $1{\sim}100mm/s$, and N and Cr contents, $0{\sim}0.27wt.%,\;25{\sim}28wt.%$ respectively, in a duplex stainless steel, CD4MCU. As the solidification rate increases, the dendrite spacing reduced and the austenite phase in the ferrite matrix became finer. The volume fraction of austenite phase increased and its shape went to be round with increasing nitrogen contents in duplex stainless alloys. The Cr alloying element, even though it is a ferrite former, showed to enhance the nitrogen solubility in the alloy and caused the austenite round and finer. Also, Cr was supposed to decrease the austenite volume fraction, but it increased the austenite slightly due to increasing nitrogen solubility during solidification.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.3
• /
• pp.197-203
• /
• 1982

The fatigue crack propagation behavior or non-heat-treatment and thermally aged type 304 stainless steel was investigated on the basis of linear elastic fracture mechanics. This Study was concentrated on the relations between the crack propagation rate and the stress intensity factor range. The following results are obtained : The precision measurement and observation of fatigue crack propagation behavior is studied with moire grating. The effect of thermally aged type 304 stainless steel is investigated under small load. In the equation da/dN=c(.DELTA. k)/SUP m/, factor m of thermally aged steel is a little higher than non-heat-treatmented steel and its limit is m=1.35-4.2.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.2
• /
• pp.73-80
• /
• 1998

The aim of this study is to develop sintered stainless steels (SSS) with good mechanical strength, wear resistance, and corrosion resistance by nitrogen ion implantation on the Culated SSS surface. Stainless steel compacts containg Cu (2-10 wt%) were prepared by electroless Cu-pating method which results in the increased3 homogenization in alloying powder. Nitrogen ion implantation was carried out by using N2 gas as the ion source. Nitrogen ions were embedded by an acceleratol of 130keV with doese $3.0\times10^{17}\;ions/\textrm{cm}^2$ on the SSS at $25^{\circ}C$ in$2\times10^{-6}$ torr vacuum. The nitrogen ion implanted SSS obtained from anodic ploarization curves revealed higher corrosion potential than that of nitrogen ion unimplante one. And nitrogen ion implanted 316LSSS had good resistance to pitting corrosion due to the synergistic effect of Mo and N, and the inhibition of $NH_4\;^+$<\TEX>, against $CI^-$<\TEX>.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.4
• /
• pp.149-154
• /
• 2011

Martensitic stainless steel STS 431 has been nitrided by active screen ion nitriding under the various temperature and time. The thickness of diffusion layer, case depth, hardness and composition phases were investigated using field emission scanning electron microscopy (FE-SEM), micro-Vickers hardness tester, X-ray diffraction (XRD) and glow discharge spectroscopy (GDS). It was observed that the thickness of diffusion layer depends strongly on the treatment temperature and time. A sample, which was nitrided at $450^{\circ}C$ for 8hours, was a maximum hardness of Hv0.01 1558 and nitride layer of $70{\mu}m$. As shown in XRD patterns, $\varepsilon(Fe_{2-3}N)$ and expanded martensite (${\alpha}_N$) phases which was saturated with nitrogen solid solution were in the nitrided layer treated at $450^{\circ}C$ for 2 hours. Composition phases of $\varepsilon$ $(Fe_{2-3}N)$ and ${\gamma}'$ ($Fe_4N$) were observed after active screen nitriding at $450^{\circ}C$ for 8 hours.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.1
• /
• pp.54-62
• /
• 1998

In this study, the behaviorof ion nitriding of AISI 304 stainless steel was investigated using plasma ion nitriding system. The characteristics of ion nitriding, and their micsoctrucyures, and physical properties were investigated as a function of process parmeteds. important conclusions can be summarzied as follows. Firstly, it was found that growth of nitride layer in ion nitriding are mainly affected by N2 partial pressures and nitriding temperatures for AISI 304 stainless steel. The $N_2$<\TEX> partial pressure plays on important role in ion nitriding since it determiness the incoming flux of nitrogen species onto specimen surface. Nitriding thmprrature is also important besauseit determines the diffusion rates of nitrogen through nitride layers. While both parameters affects the characteristics rateding are controlled by nitridingen diffusion nitration profiles of N and alloying elements such as Cr and Ni are observed through niride layers. Secondly, nitride layer consists of the upper white laywe having various nitride phases and the underneath diffusion layers. The thickness of white layer increases with $N_2$<\TEX> partial pressures and nitriding temperatures. The thinkness of diffusion layer is increasting nitriding temperatures. Finally, nitriding of stainless steels steel show slighly low their corrsionce prorerties. However, passivation properties, which is normally observed in stainless steels, were still observed aftre ion nitriding.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.157-158
• /
• 2007

AISI316L강의 내식성과 표면경도를 동시에 향상시키기 위한방법으로 저온 플라즈마 침탄과 저온 플라즈마 질화를 동일한 로 내에서 연속적으로 실시하였다. 여러 가지 공정인자 중 저온 플라즈마 질화 시 $N_2$가스가 표면에 미치는 영향을 조사 하였다. 모든 시편의 표면에 N에 의해 확장된 오스테나이트 (${\gamma}_N$)가 형성되었으며, 형성된 ${\gamma}_N$로 인하여 표면경도가 약 $3{\sim}4$배 증가하였다. $N_2$가스가 증가할수록 ${\gamma}_N$층의 두께가 증가 하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.10a
• /
• pp.265.1-265
• /
• 2001

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.289-290
• /
• 2015

In this experiment, nitriding treatment has been performed at $400^{\circ}C$ with various $N_2$ content and with changing processing time on AISI 420 martensitic stainless steel to investigate the expanded martensite layer (${\alpha}^{\prime}_N$ layer) formation behavior. Nitriding was implemented with changing $N_2$ content from 10% to 25% for 15 hrs and processing time was changed from 4hr to 15hr at 25% $N_2$ content. After treatment, the behavior of the ${\alpha}^{\prime}_N$ layer was investigated by optical microscopy, X-ray diffraction, and micro-hardness testing. Potentiodynamic polarization test was also used to evaluate the corrosion resistance of the samples. It was found that the surface hardness and ${\alpha}^{\prime}_N$ layer thickness increases with increasing $N_2$ percentage and processing time. Although their corrosion behaviors are worse than the bare sample.