• 한국해양공학회지
• /
• 제3권2호
• /
• pp.108-117
• /
• 1989

This paper deals with a fatigue life prediction of a surface crack based on the experimentally obtained relationship between surface crack length ratio $a/a_{f}$ and cycle ratio $N/N_{f}$ using micro computer. Firstly $a/a_{f}$-$N/N_{f}$ curves obtained from experimental tests, were assumed as three curves UC(the upper limit curve), LC(the lower limit curve) and MC(the middle curve), and these were utilized to predict the fatigue life. Comparing the calculated values which represent the characteristics of crack growth behaviors from the three assumed curves with the experimental ones, it has been found that in the stable crack growth region, they coincide reasonably well each other. And the differences between the fatigue lives obtained from the assumed curves and the experimental fatigue life did not exceed 20%. Using the characteristics of $a/a_{f}$-$N/N_{f}$ curves, it is possible to predict the da/dN-Kmax curves and the S-$N_{f}$ curves.

• 대한자기공명의과학회:학술대회논문집
• /
• 대한자기공명의과학회 2001년도 제6차 학술대회 초록집
• /
• pp.108-108
• /
• 2001

Purpose： To correlate the histological differentiation of hepatocellular carcinomas (HCCs) with finding on triple contrast-enhanced MR imaging using gadolinium-chelates, superparamganetic ire oxides (SPIO), and mangafodipir trisodium. Method： Ten patients with proven HCC underwent triple contrast-enhanced MRI befo surgical resection. Subjective ratings of the enhancement pattern and degree were compare with the histological grades determined on surgical specimen. Quantitative measurements signal-to-noise ratio (S/N) of the lesion and the lesion-to-liver contrast-to-noise ratio C/N on the enhanced MR images, and the degree of S/N and C/N changes between the unenhanced and enhanced images were also correlated with the histological grades.

• 한국공작기계학회논문집
• /
• 제12권6호
• /
• pp.36-43
• /
• 2003

In machining of ceramic materials, they are very difficult-to cut materials because of there high strength and hardness. Machining of ceramics are characterized by cracking and brittle fracture. Generally, ceramics are machined using conventional method such as finding and polishing. However these processes are generally costly and have low MRR(material removal rate). This paper focuses on determining the optimal levels of process parameters for products with CNC machining center. For this purpose, the optimization of cutting parameters is performed based on experimental design method. A design and analysis of experiments is conducted to study the effects of these parameters on the surface roughness by using the S/N ratio, analysis of ANOVA and F-test. Cutting parameters, namely, cutting speed, feed and depth of cut are optimized with consideration of the surface roughness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.278-282
• /
• 1996

Electrical properties of acrylic acid and n-butyl acrylate grafted polyethylene were investicated. Charge accumulation characterist-ics of acrylic acid grafted PE are changed by graft ratio, but it remains not changed in n-butyl acrylate grafted PE. It was also observed that anti-treeing and AC breakdown strength of grafted PE were increased due to the graft ratio. The change of electrical properties of grafted PE were attributed to the polar group introduced by the graft reaction.

• 폴리머
• /
• 제24권4호
• /
• pp.445-452
• /
• 2000

다양한 종류의 메탈로센 촉매와 공촉매인 개질-MAO (MMAO)을 이용한 에틸렌 (E)과 노르보르넨 (N)의 공중합에서 중합조건이 촉매 활성 및 공중합체의 구조와 성질 등에 미치는 영향을 조사하였다. 즉 $C_2$-대칭구조를 가지는 rac-Et(Ind)$_2$ZrC $l_2$, $M_2$Si(Ind)$_2$ZrC $l_2$, M $e_2$Si-(Cp)$_2$ZrC $l_2$ 및 $C_{s}$-대칭구조를 가지는 iPr(FluCp)ZrC $l_2$, 그리고 constrained geometry catalyst (CGC)와 이중다리 (di-bridged) 지르코노센 둥의 다양한 메탈로센 촉매를 사용하여 [N]/[E] 공급비에 따른 촉매 활성, 공중합체 (COC)의 열적 성질 및 N 함량을 조사하였다. rac-Et(Ind)$_2$ZrC $l_2$를 촉매로 사용한 경우에 공촉매의 몰비, 중합 온도 및 공촉매 종류 등의 중합조건을 조사한 결과 [Al]/[Zr]=3000, 4$0^{\circ}C$, MMAO 공촉매 등이 적합하였다. [N]/[E] 공급비가 증가됨에 따라 COC내의 N 함량이 증가하는 일반적인 경향을 보였으나, 촉매 활성은 사용된 메탈로센 촉매의 구조에 따라 달랐다. 즉 [N]/[E]가 증가할수록 $C_2$-대칭구조의 촉매 활성은 감소하였으나 $C_{s}$-대칭구조의 경우에는 증가하였다. 촉매활성과 N함량 등을 고려해 보면 rac-Et(Ind)$_2$ZrC $l_2$/MMAO계에서 비교적 높은 촉매 활성과 COC의 $T_{g}$제어가 용이한 결과를 얻을 수 있었다. 촉매종류에 따른 단량체의 반응성비를 Helen-Tudos 방법으로 구하였다.하였다.

• 열처리공학회지
• /
• 제22권5호
• /
• pp.267-274
• /
• 2009

Titanium Chromium Nitrided (TiCrN) coatings were deposited on stainless steel 316 L and Si (100) wafer by inductively coupled plasma assisted D.C. magnetron sputtering at the various sputtering power on Cr target and $N_2/Ar$ gas ratio. Increasing the sputtering power of Cr target, XRD patterns were changed from TiCrN to nitride $Cr_2Ti$. The maximum hardness was $Hk_{3g}$ 3900 at $0.3\;N_2/Ar$ gas ratio. The thickness of the TiCrN films increased as the Cr target power increased, and it showed over $Hk_{5g}3100$ hardness at 100 W, 150 W. TiCrN films were deposited by the ICP assisted DC magnetron sputtering shown good wear resistance as the $N_2/Ar$ gas ratio was 0.1, 0.3.

• 한국표면공학회지
• /
• 제39권2호
• /
• pp.70-75
• /
• 2006

As technology advances, there is a demand for development of hard, solid lubricant coating. (Ti,Cr)N-$MoS_2$, films were deposited on SKD 11 tool steel substrate by co-deposition of $MoS_2$, with (Ti,Cr)N using a D.C. magnetron sputtering process. The influence of the $N_2/Ar$ gas ratio, the deposition temperature, the amount of $MoS_2$ in the films, and the bias voltage on the mechanical and the structural properties of the films were investigated. Wear tests were performed on the films deposited in various conditions.

• 열처리공학회지
• /
• 제8권4호
• /
• pp.255-265
• /
• 1995

Stainless steel type 304L has been nitrided in the low pressure (600Pa) and high nitrogen (80% $N_2$+20% $H_2$) environment for 5 hours by the square-wave-pulsed-d.c. plasma as a function of temperature $400{\sim}550^{\circ}C$ and pulsation. At the lower temperature range of $400{\sim}500^{\circ}C$ and at the relatively high ratio of pulse duration to pulse period. "S-phase" has been developed in the form of thin nitrided surface layer which has many cracks, leading to be nearly impossible for the industrial anti-wear and anti-corrosion applications. At the higher temperature up to $550^{\circ}C$ with the increasing ratio of the pulse duration to pulse period up to $50{\mu}s/100{\mu}s$, the nitrided layer, whose growth rate has increased also, has been composed mainly of CrN and $Fe_4N$ phases and has become thick, uniform and nearly crack-free.

• 대한금속재료학회지
• /
• 제49권10호
• /
• pp.774-779
• /
• 2011

S-N fatigue behavior of cast 304 stainless steel was studied at 25, -50 and $-196^{\circ}C$ and at a stress ratio of -1 in uniaxial and bending loading condition. It was found that the resistance to S-N fatigue was greatly improved with decreasing testing temperature. The normalized S-N fatigue curves by tensile strength at three different testing temperatures matched each other, suggesting that tensile strength determines the S-N fatigue resistance of cast 304 stainless steel at low temperatures. The effects of different loading on the resistance to S-N fatigue of cast 304 stainless steel were quantified. The S-N fatigue curves at 25, -50 and $-196^{\circ}C$ were described by using Basquin's law the relationship between the S-N fatigue curve and the testing temperature was obtained by using a simple regression method.

• Steel and Composite Structures
• /
• 제21권1호
• /
• pp.57-72
• /
• 2016

The Poisson ratio reduction of symmetric hygrothermal aged $[{\theta}_m/90_n]_s$ composite laminates containing a transverse cracking in mid-layer is predicted by using a modified shear-lag model. Good agreement is obtained by comparing the prediction models and experimental data published by Joffe et al. (2001). The material properties of the composite are affected by the variation of temperature and transient moisture concentration distribution in desorption case, and are based on a micro-mechanical model of laminates. The transient and non-uniform moisture concentration distribution give rise to the transient Poisson ratio reduction. The obtained results represent well the dependence of the Poisson ratio degradation on the cracks density, fibre orientation angle of the outer layers and transient environmental conditions. Through the presented study, we hope to contribute to the understanding of the hygrothermal behaviour of cracked composite laminate.