• Nuclear Engineering and Technology
• /
• v.42 no.3
• /
• pp.319-328
• /
• 2010

Bonded tendons have been used in reactor buildings at some operating nuclear power plants in Korea. Assessing prestress force on these bonded tendons has become an important pending problem in efforts to assure continued operation beyond their design life. The System Identification (SI) technique was thus developed to improve upon the existing indirect assessment technique for bonded tendons. As a first step, this study analyzed the sensitivity of the key parameters to prestress force, and then determined the optimal parameters for the SI technique. A total of six scaled post-tensioned concrete beams with bonded tendons were manufactured. In order to investigate the correlation of the natural frequency and the displacement to prestress force, an impact test, a Single Input Multiple Output (SIMO) sine sweep test, and a bending test using an optical fiber sensor and compact displacement transducer were carried out. These tests found that both the natural frequency and the displacement show a good correlation with prestress force and that both parameters are available for the SI technique to predict prestress force. However, displacements by the optical fiber sensor and compact displacement transducer were shown to be more sensitive than the natural frequency to prestress force. Such displacements are more useful than the natural frequency as an input parameter for the SI technique.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.141-142
• /
• 2009

This study discusses attempt of utilizing the natural frequencies to evaluate the effective stress of post-tensioned, external tendon in field. This type of structure has distinct advantage of good accessibility of tendon, which is considered to be one of essential elements in entire bridge. Six tendons in single span of PSC bridge were applied. They were excited using an impact hammer and corresponding vibrations were measured using multiple accelerometers. The stiff string model in idealized conditions was used to evaluate the effective stress in tendons.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.392-397
• /
• 1997

In this paper, design and analysis of anchorage zone in prestressed concrete structure using nonlinear strut and tie model is presented. Nonlinear strut and tie model is an analysis and design model which constructs strut and tie model based on nonlinear analysis considering the nonlinear behavior of concrete. Based on the nonlinear strut and tie model, the analysis and design are performed for the anchorage zone having singular concentric tendons, singular eccentric tendons and multiple tendons, respectively. For verification of the model, comparisons are made with experimental results as well as results by linear strut and tie models. from the comparisons, it is shown that the design of the anchorage zone by the nonlinear model is still economical without loosing the degree of safety and the prediction of the ultimate load by the nonlinear model gives better accuracy than by the linear one.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.2
• /
• pp.159-166
• /
• 2000

The development of external prestressing methods has been one of the major trends in the concrete bridge constructions over the past decades. One of the promising methods to enhance the flexural strength of a externally prestressed girder is to place the tendons with large eccentricities. The analysis and design of composite girders prestressed by external tendons involve difficulties related mainly to the position of anchorages and the construction sequences. This study was conducted on the concrete bridges reinforced by the continuous girders and the external prestressing. The test results in this study showed that the external prestressing of a composite girder increased the range of the elastic behavior, reduced deflections, increased ultimate strength, and added to the redundancy by providing the multiple stress paths.

• Clinics in Shoulder and Elbow
• /
• v.10 no.2
• /
• pp.160-166
• /
• 2007

Purpose: The current study assessed the factors affecting outcomes of primary repair procedures in tears of multiple rotator cuff tendons. Materials and Methods: Among the cases of rotator cuff tears involving two or more tendons receiving operations between 1997 and 2003, The clinical results of 19 cases with more than 2 years follow-up were evaluated by the UCLA score. We evaluated the correlation of trauma, active motion, acromiohumeral distance, tear size, and surface area with the UCLA score using Pearson's linear correlation coefficient (PLCC). Results: UCLA scores increased significantly in all cases, from 9 to 26.1 on average. However, the results were good in 53%, and poor in 47% according to Ellman's criteria. Trauma, active elevation, acromiohumeral distance, and tear size did not correlate with the UCLA score, but the tear surface area was inversely correlated with the score (PLCC=-0.696). Cases with degeneration of the infraspinatus muscle above Goutallier grade III on MRI showed worse results than cases with less degeneration. Conclusion: The clinical results of primary repair of rotator cuff tears involving multiple tendons were satisfactory in 53% of patients. Large tear surface area and severe degeneration of the infraspinatus were poor prognostic factors.

• Journal of Mechanical Science and Technology
• /
• v.17 no.8
• /
• pp.1164-1170
• /
• 2003

The objectives of this work here focus on the differences in responses to multiple cyclic tests of different sections along the length of the same tendon. Tendon specimens were obtained from the hindlimbs of canines and frozen to -70$^{\circ}C$. After thawing, specimens were mounted in the immersion bath at room temperature (22$^{\circ}C$) , preloaded to 0.13 N and then subjected to 3% or 4% of the initial length at a strain rate of 5%/sec. It was found that different sections of the same long tendons had different resistances to deformation. In general, the bone end sections were stiffer and carried greater loads for a given strain than the muscle end sections, and the mid-portions were the least stiff and carried the smallest loads for a given strain. The results of this study offer new information about the mechanical responses of collagenous tissues. We know more about their responses to multiple cyclic extensions and how their responses are different from the positions along the length of the tendon specimen. The nature and causes of these differences in the stiffness are not fully known. However, it is clear that differences in the mechanical response of tendons and other connective tissues are significant to musculoskeletal performance.

• The Academic Congress of Korean Shoulder and Elbow Society
• /
• 2009.03a
• /
• pp.90-90
• /
• 2009

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.33-41
• /
• 2011

This study presents modeling technologies applicable to an unbonded post-tension system using a finite element software package. In this study, both direct modeling method and multiple spring method were used. The direct modeling method adopts tube-to-tube contact elements to represent the physical feature of a post-tension system. The multiple spring method uses virtual tendons attached to the real tendons using a number of rigid axial springs that freely rotate at the ends. Both modeling technologies provide accurate predictions. However, only the multiple spring method provides numerically stable and reliable responses with a consideration of concrete tension stiffening effects. Therefore, the multiple spring method turned out to be a generally applicable modeling technology for the unbonded post-tension system. Comparisons were made for the analytical and experimental results for the verification of the selected method, and parameter studies were carried out to confirm the appropriateness of the modeling assumptions and parameters adopted in the analysis.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.681-684
• /
• 1999

The development of external prestressing methods has been one of the major trends in the concrete bridge constructions over the past decades. One of the promising methods to enhance the flexural strength of a externally prestressed girder is to place the tendons with large eccentricities. The test results in this study showed that the external prestressing of a composite girder increased the range of the elastic behavior, reduced deflections, increased ultimate strength, and added to the redundancy by providing the multiple stress paths. This study was conducted on the concrete bridges reinforced by the continuous girders and the external prestressing.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.6
• /
• pp.1329-1339
• /
• 1994

The purpose of present study is to explore the mechanical behavior of anchorage zones in prestressed concrete members with single and closely-spaced multiple tendon anchorages. The cracking loads and local stress distributions at these anchorage zones are studied. To this end, a series of experiments have been conducted. From this study, it is found that the failure of anchorage zones of the closely-spaced multiple tendon members is initiated by cracking along the tendon path and that the tensile stresses arising in the vicinity of anchorage zone of the first tendon are reduced due to additional compression of the second tendon. This results in the increase of cracking capacity of the member. The effects of multiple tendons are presented in the form of strain distribution and cracking load comparisons.